Search Results

With the proliferation of electric vehicles in the market, it has become important for Automotive OEMs (Original Equipment Manufacturers) to focus on delivering a higher driving range while also maximizing performance. One approach OEMs are actively considering in meeting this goal is to include a secondary drive axle disconnect into the powertrain which has the potential to improve the overall driving range by about 6-8.3% [4]. This paper outlines the need for a novel controls architecture to make the Powertrain controls software modular and to reduce the development time needed to provide robust powertrain control software. To do this, the electrified powertrain torque controls at STELLANTIS NV takes a decentralized controls architecture approach, by separating the axle disconnect controls subsystem (ADCS) from the primary path of torque controls. The ADCS takes in information such as the desired axle state and controls the axle disconnect actuators to achieve that state.

Warranty forecasting of repairable systems is very important for manufacturers of mass produced systems. It is desired to predict the Expected Number of Failures (ENF) after a censoring time using collected failure data before the censoring time. Moreover, systems may be produced with a defective component resulting in extensive warranty costs even after the defective component is detected and replaced with a new design. In this paper, we present a forecasting method to predict the ENF of a repairable system using observed data which is used to calibrate a Generalized Renewal Processes (GRP) model. Manufacturing of products may exhibit different production patterns with different failure statistics through time. For example, vehicles produced in different months may have different failure intensities because of supply chain differences or different skills of production workers, for example.

For the designing of world class vehicles, ride comfort is one of the criteria that vehicle manufacturers are constantly trying to improve. The automotive seating system is an important sub-system in a vehicle that contributes to the ride comfort of the vehicle occupants. Seat vibrations are perceived by the occupants and make them feel uncomfortable during driving conditions. These vibrations are majorly transferred from engine and road excitation loads. For road excitation loads, the road testing may not be accurately repeatable, and measurements based on four post shakers are used to assess the discomfort. The major challenges for the vehicle manufactures is the availability of physical prototypes at an early stage of vehicle development and any changes in the design due to test validation leads to huge cost and time.

Use of parametric approach to optimize CAE models for various objectives is a common practice these days. In addition to load members, the connection entities such as welds and adhesives play an important role in overall performance matrix. Hence adding the connection entities to the pool of design variables during an optimization exercise provide additional opportunity for design exploration. The method presented in this paper offers a unique approach to parameterize adhesive lines by evaluating the possibility of using structural adhesives as intermittent patches rather than continuous lines. The paper discusses two optimization studies 1) structural adhesive patches along with spot weld pitch as design variables, and 2) structural adhesive patches with gage variables. These studies include the Body in White (BiW) and Trimmed Body in White (TBiW) assessments.

The advanced Optimization techniques help us in exploring the light weight architecture. This paper explains the process of designing a lightweight track bar bracket, which satisfies all durability performance targets. The mounting locations and load paths are critical factors that define the performance and help in the development of weight efficient structure. The process is to identify the appropriate bolt location through Design of Experiment (DOE) and topology based studies; followed by section and shape optimization that help to distribute material in a weight efficient manner across the structure. Load path study using topology optimization is performed to identify the load path for durability load cases. Further shape optimization is done using hyper study to determine the exact thickness of the webs and ribs. A significant weight reduction from the baseline structure is observed. This process may be applicable for all casting components.

Material formability is a very important aspect in the automotive stamping, which must be tested for the success of manufacturing. One of the most important sheet metal formability parameters for the stamping is the edge tear-ability. In this paper, a novel test method has been present to test the aluminum sheet edge tear-ability with 3D digital image correlation (DIC) system. The newly developed test specimen and fixture design are also presented. In order to capture the edge deformation and strain, sample's edge surface has been sprayed with artificial speckle. A standard MTS tensile machine was used to record the tearing load and displacement. Through the data processing and evaluation of sequence image, testing results are found valid and reliable. The results show that the 3D DIC system with double CCD can effectively carry out sheet edge tear deformation. The edge tearing test method is found to be a simple, reliable, high precision, and able to provide useful results.

Draw beads are widely used in the binder of a draw die for regulating the restraining force and control the draw-in of a metal blank. Different sheet materials and local panel geometry request different local draw bead configurations. Even the majority of draw bead is single draw bead, the alternative double draw bead does have its advantages, such as less bending damage may be brought to the sheet material and more bead geometry features available to work on. In this paper, to measure the pulling force when a piece of sheet metal passing through a draw bead on an inclined binder, the AA5XXX and AA6XXX materials were tested and its strain were measured with a digital image correlation (DIC) system. Five different types of double bead configurations were tested. The beads are installed in a Stretch-Bend-Draw-System (SBDS) test device. The clearance between a male and a female bead is 10% thicker than the sheet material. A tensile machine was used to record the pulling force.

Light-weighting vehicles cause an increase in Aluminum Alloy stamping processes in the Automotive Industry. Surface finish and lubricants of aluminum alloy (AA) sheet play an important role in the deep drawing processes as they can affect the friction condition between the die and the sheet. This paper aims to develop a reliable and practical laboratory test method to experimentally investigate the influence of surface finish, lubricant conditions, draw-bead clearances and pulling speed on the frictional sliding behavior of AA 6XXX sheet metal. A new double-beads draw-bead-simulator (DBS) system was used to conduct the simulated test to determine the frictional behavior of an aluminium alloy with three surface lubricant conditions: mill finish (MF) with oil lube, electric discharge texture (EDT) finish with oil lube and mill finish (MF) with dry lube (DL).

Bendability is one of the most important formability characteristics in sheet metal forming, so it has to be understood for robust aluminum stamping process designs. Crack is one of the major failure modes in aluminum sheet bending. In this study, a new “incremental bending” method is proposed to reduce the risk of bending failure. A novel laboratory test methodology is conducted to test the 5xxx series aluminum sheet bendability with 3D digital image correlation (DIC) measurement system. The designs of test apparatus and test procedure are introduced in this paper. Through the data processing and evaluation of a sequence image acquisition, the major strain histories within the zone of the through thickness crack of test samples are measured. Testing results show that incremental bending is capable of reducing peak strain on the outer surface obviously compared with traditional non-incremental bending. The more step, more movement, the more peak strain reduction.

This research studies the transformation kinetics of austempered ductile iron (ADI) with and without nickel as the main alloying element. ADI has improved mechanical properties compared to ductile iron due to its ausferrite microstructure. Not only can austempered ductile iron be produced with high strength, high toughness and high wear resistance, the ductility of ADI can also be increased due to high carbon content austenite. Many factors influence the transformation of phases in ADI. In the present work, the addition of nickel was investigated based on transformation kinetics and metallography observation. The transformation fractions were determined by Rockwell hardness variations of ADI specimens. The calculation of transformation kinetics and activation energy using the “Avrami Equation” and “Arrhenius Equation” is done to describe effects of nickel alloy for phase reactions.

Vehicle suspension parts are subjected to variable road loads, manufacturing process variation and high installation loads in assembly process. These parts must be robust to usage conditions to function properly in the field. Design for Six Sigma (DFSS) tools and Taguchi Method were used to optimize initial rear suspension trailing arm design. Project identified key control factor/design parameters, to improve part robustness at the lowest cost. Optimized design performs well under higher road loads and meets stringent durability requirements. This paper evokes use of Taguchi Method to design robust rear suspension trailing arm and study effect of selected design parameters on robustness, stress level/durability and part cost.

Threaded fasteners or bolted joints are used extensively in automotive assemblies. There are standard procedures to evaluate joint performance under block cycles or road loads. The deciding load case for such joint design is slippage analysis of the joint. There are studies done to evaluate the theoretical and experimental behavior of these joints. There are different ways of understanding the interaction between the bolt and the nut under different loading scenarios. However, none have provided a satisfactory method of quantifying bolt loosening or loss of clamp load under cyclic loading, where no slippage is observed. Under varying loads, initial relaxation of the joint is followed by a loss of clamping load. Below a critical value, complete loss of clamping load progresses very rapidly and this results in a loose joint.

Damages (fracture) in metals are caused by material degradation due to crack initiation and growth due to fatigue or dynamic loadings. The accurate and realistic modeling of an inelastic behavior of metals is essential for the solution of various problems occurring in engineering fields. Currently, various theories and failure models are available to predict the damage initiation and the growth in metals. In this paper, the failure of aluminum alloy is studied using progressive damage and failure material model using Abaqus explicit solver. This material model has the capability to predict the damage initiation due to the ductile and shear failure. After damage initiation, the material stiffness is degraded progressively according to the specified damage evolution response. The progressive damage models allow a smooth degradation of the material stiffness, in both quasi-static and dynamic situations.

In recent years, there has been renewed attention focused on open jet correction methods, in particular on the two-measurement method of E. Mercker, K. Cooper, and co-workers. This method accounts for blockage and static pressure gradient effects in automotive wind tunnels and has been shown by both computations and experiments to appropriately adjust drag coefficients towards an on-road condition, thus allowing results from different wind tunnels to be compared on a more equitable basis. However, most wind tunnels have yet to adopt the method as standard practice due to difficulties in practical application. In particular, it is necessary to measure the aerodynamic forces on every vehicle configuration in two different static pressure gradients to capture that portion of the correction. Building on earlier proof-of-concept work, this paper demonstrates a practical method for implementing the two-measurement procedure and demonstrates how it can be used for production testing.

Vehicle suspension parts are subjected to variable road loads, manufacturing process variation and high installation loads in assembly process. Seam welding can be considered as such process to connect more components and parts. Typical in a Mc Pherson suspension system stabilizer bar link is connected to the strut assembly through ball stud and clamped to a bracket welded to the outer strut tube. Cracks have been observed in the stabilizer bar link bracket welds of vehicles in the field, effecting the functionality of the suspension system. During preliminary phase of product development CAE assessment of the seam weld is carried out against road load data, if the design does not meet the targets enabler studies are carried out in an iterative approach. Various design variables (control factors) can be considered to carry out the iterations.

A vehicle’s exterior fit and finish, in general, is the first system to attract customers. Automotive exterior engineers were motivated in the past few years to increase their focus on how to optimize the vehicle’s exterior panels split lines quality and how to minimize variation in fit and finish addressing customer and market required quality standards. The design engineering’s focus is to control the deviation from nominal build objective and minimize it. The fitting process follows an optimization model with the exterior panel’s location and orientation factors as independent variables. This research focuses on addressing the source of variation “contributed factors” that will impact the quality of the fit and finish. These critical factors could be resulted from the design process, product process, or an assembly process. An empirical analysis will be used to minimize the fit and finish deviation.

The crashworthiness of body-in-white (BIW) plays a vital role in full vehicle crash performance. The structural integrity of BIW is controlled via strength of the spot welds and adhesives that are the primary entities to join sheet metal. The number of welds and amount of adhesives in the entire BIW directly affects the cost and the cycle time of the BIW; which makes them a good candidate for optimization. However optimization of the welds and/or adhesives not only reduces the number of connections but also provides the opportunity to improve the structural performance and mass saving by placing them optimally for the structural responses. This paper discusses the optimization of full vehicle structural performance for the small overlap crash event using the length of adhesives in the BIW as parameters. Included in the study were length of the adhesives and gage variables, defined in the front-end structure of the vehicle.

Currently the On-Board Diagnostics (OBD) requirements enforced by government agencies do not cover electric vehicles. Although the California Air Resources Board (CARB) mandates all light and medium duty vehicles and heavy duty engine dynamometer certified engines equipped with fossil fuel-powered engines, including all hybrid vehicles, must follow the OBD requirements in California Code of Regulation (CCR) 1968.2 and 1971.1, Battery Electric vehicles (BEVs), are exempted from OBD requirements. The legislators, such as CARB, have started to make proposals for on-board systems to monitor electric propulsion system health. In addition, there may be customer needs to obtain standard vehicle service information and the Original Equipment Manufacturers (OEMs) may also have the desire for common diagnostic strategies across different vehicle applications to lower the development costs.

In the light duty diesel segment, the need persists for an advanced control system to monitor the health of an aftertreatment system throughout a vehicle’s life in order to maintain compliance with ever tightening emissions levels. In on-board diagnostics (OBD), every diagnostic is validated during development stages to detect when a system under monitoring of that diagnostic has failed. This necessitates the need to create parts which represent a failure that would be observed on the vehicle. These failed parts, referred to as limit or threshold parts, are developed through a limit part creation process. Although there are commonalities amongst Original Equipment Manufacturers (OEM), each OEM has their own detection logic which will require a unique and specific limit part. Various methods exist for creating these limit parts, and each method produces a different combination of ability to detect the failure and its associated tailpipe emissions.

Twist spring-back would interfere with stamping or assembling procedures for advanced high strength steel. A “homeopathic” resolution for controlling the twist spring-back is proposed using unbalanced post-stretching configuration. Finite element forming simulation is applied to evaluate and compare the performance for each set of unbalanced post-stretching setup. The post-stretching is effectuated by stake bead application. The beads are separated into multiple independent segments, the height and radii of which can be adjusted individually and asymmetrically. Simulation results indicate that the twist spring-back can be effectively controlled by reducing the post-stretching proximate to the asymmetric part area. Its mechanism is qualitatively revealed by stress analyses, that an additional but acceptable cross-sectional spring-back re-balances the sprung asymmetrical geometry to counter the twist effect.