Search Results

Technological progress opens the door for the development of new tools to be used for the development of vehicles and engines. This offers the opportunity for an optimization of the entire workflow on one hand, and an improvement of single tasks on the other hand. This paper describes the actual status of the development process, describes new directions of tool evolvement and finally gives an outlook into the future. Redline ADAPT-SIM is a tool for driver- and vehicle simulation, which was developed primarily for ECU application, but can also be used for other dynamic testing tasks. The introduction of this tool leads to better controllability and therefore also repeatability of tests.

This paper describes the rapid development of the Ford GT transmission, from concept phase to production, where the technical challenges involved are implicit in the specifications provided. It presents the steps taken at a project management level to expedite development, as well as the tools used to design and rate components at the design stage. Examples of concurrent engineering are given as well as management techniques used to predict and address key risks. In addition, details of analysis and test procedures are given, underlining their contribution to the rapid introduction of the transmission to the market place.

Software has becoae an inherent and critical component of electronic automotive instrumentation products. The demand for new software development has been increasing at alarming rates, To meet this demand and still provide quality software, the philosophies and methodologies of software engineering must be understood and utilized. This paper discusses the basic concepts of software engineering, the software development life cycle and software development tools and techniques. It also addresses unique points οf interest that are applicable to software engineering in the electronic automotive instrumentation environment.

The Service Bay Diagnostic System (SBDS) will be designed to assist the dealership technician in diagnosing and repairing Ford Motor vehicles. The system hardware will be configured around a Service Bay Computer with mass storage capability and auxiliary service equipment. Major system features include: guided service writer/customer interaction, interactive vehicle diagnostics, information management. capabilities, and an additional aid to identifying intermittent failures through the use of a portable over-the-road data acquisition device. In order to assist the technician in properly diagnosing the causal factor, the Service Bay Computer System will also be enhanced through the use of an expert system knowledge base.

This paper describes the steps utilized in the development of the Flex Fuel program by the Ford South America Product Development team to implement a reliability plan. A reliability plan, understood as series of tools to avoid failure mode occurrence, is particularly important when introducing a new technology. Robustness, as the ability of a system to perform its intended function in the presence of variable operational conditions, is contained in the reliability concept and is a key aspect of this plan. Several factors that could affect the vehicle performance were listed, classified and prioritized in order to establish a preventive action plan. The tools were used first at the vehicle level, and then cascaded down to subsystem and component level. Also, with the results of this analysis, design verification methods were enhanced to capture real world usage conditions.

This article describes both a computer-aided engineering tool - a computer model - utilized in accelerating design tasks and also the process of building a powertrain design knowledge. The computer model, which integrates engineering and analysis phases into the design process, has been developed to enable rapid evaluation of new powertrain concepts. The model determines the basic geometry of engine and transmission subsystems and components, and allows automation of the engineering and analysis processes. Examples of application of the tool in evaluation of powertrain concepts and the design of components and subsystems are also given.

Calculating the bearing reliability and behavior is one of the primary tasks which have to be performed to define the main dimensions of the cranktrain of an internal combustion engine. Since the bearing results are essential for the pre-layout of the cranktrain, the conclusion on the bearing safety should be met as early as possible. Therefore detailed simulations like T-EHD or EHD analysis may not be applied to define the dimensions in such an early development phase. In the frame of this study a prediction methodology, based on a HD bearing approach, for bearing reliability of inline-4 crankshafts of passenger cars is proposed. In this way not only the design phase is shortened but also achieving the optimal solution is simplified. Moreover the requirement of a CAD model is eliminated for the preliminary design phase. The influencing parameters on the bearing behavior are first selected and divided into two groups: geometry and loading.

Rapid Prototyping, Fabrication and Tooling is a process that blends a series of technologies (machines, tools, and methods) capable of generating physical objects directly from a CAD database. The process dramatically reduces the time spent during product development by allowing for fast visualization, verification, iteration, optimization, and fabrication of parts and tools. Many new techniques of tooling have been and are being developed by using rapid fabricated parts. These are having a dramatic impact on both timing and costs throughout the automotive industry. One area that these methods can be utilized to their full potential is motorsports. Of particular interest is the growing use of bridge tooling to provide first article through production intent parts that promote cost effective changes.

ONE plastic model is worth 40 lb of blueprints and 40 hr of the explaining that goes along with the prints, according to engineers who have worked with the new plastic “toys” which can serve as perfectly scaled miniatures for virtually every phase of automobile design and manufacture. The extensive benefits occasioned by this revolution in methods may be summarized thus: 1. Shortens design development time by providing a third-dimension evolvement of structure and form. 2. Used in advance discussions for compromising engineering and manufacturing problems, showing construction so clearly that troublesome problems are foreseen; thus enabling clear-cut, reliable decisions with a minimized chance of encountering major revisions. 3. Show in one minute what could not be found on prints for hours, saving time over any other methods, while generating valuable counterproposals reducing costs, operations, man-hours, and so forth. 4.

QFD, FMEA, Process Improvement, Taguchi, Simultaneous Engineering, PDP, Project Management, DVP, DOE, …and the list goes on. Today's automotive product design engineers face a myriad of “tools” (methodologies, techniques, procedures) that are expected to be mastered and used in the course of performing their job. The list continually grows with new tools being added to the existing ones. And each new tool has an associated acronym to add to the confusion. New and inexperienced engineers are often confused by these tools being tossed at them …school did not cover all this ! The experienced engineer is often skeptical. After all, “if I have been a successful engineer for 20 years, why do I need to start doing these things now?” Nevertheless, most of these tools are truly needed by engineers today in order to be competitive in the increasingly complex and sophisticated world of automotive product design.

Lookup tables and functions are widely used in real-time embedded automotive applications to conserve scarce processor resources. To minimize the resource utilization, these lookup tables (LUTs) commonly use custom data structures. The lookup function code is optimized to process these custom data structures. The legacy routines for these lookup functions are very efficient and have been in production for many years. These lookup functions and the corresponding data structures are typically used for calibration tables. The third-party calibration tools are specifically tailored to support these custom data structures. These tools assist the calibrators in optimizing the control algorithm performance for the targeted environment for production. Application software typically contains a mix of both automatically generated software and manually developed code. Some of the same calibration tables may be used in both auto generated and hand-code [ 1 ] [ 2 ].

Over the last decades, the use of computers has become an integral part of the engine development process. Computer-based tools are increasingly used in the design process, and especially the layout of the various subsystems is conducted by means of simulation models. Computer-aided engineering plays a central role e.g. in the design of the combustion process as well as with regards to work performed in the area of engine mechanics, where CFD, FEM, and MBS are applied. As a parallel trend, it can be observed that various engine performance characteristics such as e.g. the specific power output and the power-to-weight ratio have undergone an enormous increase, a trend which to some extent counteracts the increase in safety against malfunction and failure. As yet, due to the constant need for further optimization, mechanical testing and verification processes have not become redundant, and it is assumed that they will remain indispensable for the foreseeable future.

Work has been performed to study side glass vibrations of a typical automobile using a scanning laser vibrometer. The objective of this work was to achieve better understanding of the source and path mechanisms for aeroacoustically generated wind noise. As a tool for measuring aeroacoustically generated vibrations, the laser vibrometer presents many advantages over traditional methods. These advantages, discussed in this paper, include rapid setup, full field imaging, high spacial resolution, non-contact operation, and wide dynamic and frequency ranges.

We report measurements of interior automotive cabin forced acoustical response (SPL) as a function of frequency from 1 Hz to 200 Hz. The acoustical response was measured at eight positions in the vehicle tested, approximating the positions of passengers and points in between passengers. Variances in experimental data arising from the manner in which measuring equipment is setup in a particular vehicle are reported, and variations in data taken in similarly equipped vehicles are also reported. The purpose of these tests is to determine the measurement variability of a typical vehicle acoustic test.

The emerging global economy and global competition is having a significant impact on the management of businesses around the world. Customer satisfaction is essential. Quality of products and services and their reliability over time play a major role in satisfying the customer. A change in the mindset of organizations is required to meet these challenges. The focus of reliability efforts must shift from prediction to continuous improvement. Process oriented thinking along with the concept of the internal customer must permeate the entire organization. Mechanisms like a reliability operating process must be in place to capture lessons learned from prior failures and prevent their recurrence. Reliability disciplines - not reliability engineers - need to be deployed throughout the organization. An environment must be created which empowers self managed teams to apply these disciplines throughout the product planning, design, development, manufacturing, assembly and service processes.

Computer simulations of vehicle dynamics can be a useful investigative tool in drive-ability and NVH studies. As the present work demonstrates, oscillations of the drive-train under steady-state and transient conditions are amenable to mathematical analysis, especially in the torsional mode. Simulations of such a system with a lock-up torque converter are shown with emphasis on tip-in response, transmissibility of engine firing pulsations and self-excited oscillations. In particular, the method of interactive simulation is shown to be an effective design-aid tool in the investigation of drivetrain vibrations.

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

The LDH (Limiting Dome Height Test) is widely used at Ford Motor Co. stamping plants laboratories to monitor the formability of incoming sheet materials. Although the LDH test is very easy to implement and interpret, variability of the results and poor reproducibility between laboratories limit its acceptance. In this investigation, some of the causes of variability and differences between plant laboratories are discussed. Much of the experimental work was done at plant laboratories and the results are directly applicable to quality control (QC) machines. It was found that the binder force and the binder shape have a big influence on the results, and they should be carefully controlled. The binder cleaning procedure is also relevant to the test variability. Punch temperature has a much greater influence on QC machines than on research machines and a method for controlling the punch temperature in QC machines is presented.

The Bag Mini-diluter (BMD) is a proportional exhaust sampling system that is being studied as an improved measurement system for ultra-low level vehicle exhaust emissions. The traditional method for sampling vehicle exhaust has been the constant volume sampler (CVS) technique. This method dilutes the entire exhaust output from the vehicle, meters the mixture, and then takes a proportional sample for measurement. In contrast, the Mini-diluter sampling method meters a small sample of raw exhaust, and then dilutes this sample to a fixed dilution ratio. This approach offers new opportunities to improve the quality of the sample measurement at very low levels, which will be crucial for accurate vehicle exhaust emission measurements on vehicles that meet the ULEV and SULEV standards. A number of test programs have compared the performance of the Mini-diluter to the CVS on vehicles certified to Tier 1 and LEV standards, and the results demonstrated favorable correlation.