Search Results

Further improvements of internal combustion engines to reduce fuel consumption and to face future legislation constraints are strictly related to the study of mixture formation. The reason for that is the desire to supply the engine with homogeneous charge, towards the direction of a global stoichiometric blend in the combustion chamber. Fuel evaporation and thus mixture quality mostly depend on injector atomization features and charge motion within the cylinder. 3D-CFD simulations offer great potential to study not only injector atomization quality but also the evaporation behavior. Nevertheless coupling optical measurements and simulations for injector analysis is an open discussion because of the large number of influencing parameters and interactions affecting the fuel injection’s reproducibility. For this purpose, detailed numerical investigations are used to describe the injection phenomena.

This paper presents a quasi-dimensional emission model for calculating the transient nitric oxide emissions of a diesel engine. Using conventional and high-speed measurement technology, steady-state and transient emissions of a V6 diesel engine were examined. Based on measured load steps and steady-state measurements a direct influence of the combustion chamber wall temperature on the nitric oxide emissions was found. Load steps to and from, as well as steady-state measurements down to almost stoichiometric global combustion air ratios were used to examine the behavior of nitric oxide formation under these operating conditions. An existing emission model was expanded in order to represent the direct influence of the combustion chamber wall temperature on the nitric oxide emissions as well as enabling the forecasting of nitric oxide emissions at low global combustion air ratios: Both particularly important aspects for the simulation of transient emissions.

As the late combustion phase in SI engines is of high importance for a further reduction of fuel consumption and especially emissions, the impacts of unburnt mass, located in a small volume with a relatively large surface near the wall and in the top land volume, is of high relevance throughout the range of operation. To investigate and quantify the respective interactions, a state of the art Mercedes-Benz single cylinder research SI-engine was equipped with extensive measurement technology. To detect the axial and radial temperature distribution, several surface thermocouples were applied in two layers around the top land volume. As an additional reference, multiple surface thermocouples in the cylinder head complement the highly dynamic temperature measurements in the boundary zones of the combustion chamber.

For long haul transport, diesel engine due to its low fuel consumption and low operating costs will remain dominant over a long term. In order to achieve CO2 neutrality, the use of electricity-based, synthetic fuels (e-fuels) provides a solution. Especially the group of oxymethylene ethers (OME) is given much attention because of its soot-free combustion. However, the new fuel properties and the changed combustion characteristics place new demands on engine design. Meanwhile, the use of new fuels also creates new degrees of freedom to operate diesel engines. In this work, the application of dimethoxymethane (OME1) is investigated by means of 1D simulation at three operating points in a truck diesel engine. The subsystems of fuel injection, air path and exhaust gas are sequentially adjusted for the purpose of low emissions, especially for low nitrogen oxides (NOx).

More than 20 years after the first presentation of the heat transfer equation according to Bargende [1,2], it is time to introduce some useful additions and enhancements, with respect to new and advanced combustion principles like diesel- and gasoline- homogeneous charge compression ignition (HCCI). In the existing heat transfer equation according to Bargende the calculation of the actual combustion chamber surface area is formulated in accordance with the work of Hohenberg. Hohenberg found experimentally that in the piston top land only about 20-30% of the wall heat flux values from the combustion chamber are transferred to the liner and piston wall. Hohenberg explained this phenomenon that is caused by lower gas temperature and convection level in charge within the piston top land volume. The formulation just adds the existing piston top land surface area multiplied by a specified factor to the surface of the combustion chamber.

Two combustion models are presented: A quasi-dimensional approach, based on the injection shape and an empirical model. Both models have computation times of less than one second per cycle. The quasi-dimensional approach for CI combustion discretizes the injection jet in slices. Pilot-injections are modeled as separate zones. The forecast capability and the limitations of the model are discussed on the basis of measurements. Mentioned above the base of the quasi-dimensional model is the injection rate. Often it is difficult to obtain these data. There is therefore another empirical approach for combustion, which does not need the injection rate as input. Both models have to be calibrated. This can be done by an automatic calibration tool on the basis of the advanced Powell method. The differences and advantages compared with other optimization methods are shown. Emission-simulation models are highly important in simulating CI engines.

A new phenomenological CI combustion model was developed. Within this model the given injection rate may contain an arbitrary number of injections during one cycle. Another target was a short computation time of one second per cycle on average. The new approach should also have the ability to simulate a wide engine spectrum from passenger-car engines through to marine engines. The ignition delay is calculated separately for each single injection. In this way the model depicts the influence of pilot injections on the ignition delay of proximate injections. Each pilot injection is modeled as a single air-fuel mixture cloud with air entrainment. The burn rate of the pilot injection is modeled as a function of flame propagation and of the current local excess air ratio. If the local excess air ratio becomes too lean the pilot combustion stops or does not start at all. Main and post-injections are calculated by means of a slice approach.

In order to meet increasingly stringent exhaust emission regulations, new engine concepts need to be developed. Lean combustion systems for stationary running large gas engines can reduce raw NOx-emissions to a very low level and enable the compliance with the exhaust emission standards without using a cost-intensive SCR-aftertreatment system. Experimental investigations in the past have already confirmed that a strong reduction of the charge air temperature even below ambient conditions by using an absorption chiller can significantly reduce NOx emissions. However, test bench operation of large gas engines is costly and time-consuming. To increase the efficiency of the engine development process, the possibility to use 0D/1D engine simulation prior to test bench studies of new concepts is investigated using the example of low temperature charge air cooling. In this context, a reliable prediction of engine efficiency and NOx-emissions is important.

The target of the upcoming automotive emission regulations is to promote a fast transition to near-zero emission vehicles. As such, the range of ambient and operating conditions tested in the homologation cycles is broadening. In this context, the proposed work aims to thoroughly investigate the potential of post-oxidation phenomena in reducing the light-off time of a conventional three-way catalyst. The study is carried out on a turbocharged four-cylinder gasoline engine by means of experimental and numerical activities. Post oxidation is achieved through the oxidation of unburned fuel in the exhaust line, exploiting a rich combustion and a secondary air injection dedicated strategy. The CFD methodology consists of two different approaches: the former relies on a full-engine mesh, the latter on a detailed analysis of the chemical reactions occurring in the exhaust line.

CNG direct injection is a promising technology to promote the acceptance of natural gas engines. Among the beneficial properties of CNG, like reduced pollutants and CO2 emissions, the direct injection contributes to a higher volumetric efficiency and thus to a better driveability, one of the most limiting drawbacks of today’s CNG vehicles. But such a combustion concept increases the demands on the injection system and mixture formation. Among other things it requires a much higher flow rate at low injection pressure. This can be only provided by an outward-opening nozzle due to its large cross-section. Nevertheless its hollow cone jet with a specific propagation behavior leads to an adverse fuel-air distribution especially at higher loads under scavenging conditions. This paper covers numerical and experimental analysis of CNG direct injection to understand its mixture formation.

Due to increasingly strict emission regulations, lean combustion concept has become an essential direction of internal combustion engine development to reduce engine emissions. However, lean combustion will lead high combustion instability and unpredictive engine emissions. The combustion instability is represented as the high cycle-to-cycle variation. Therefore, understanding the mechanism of cycle-to-cycle variation is crucial for the internal combustion engine design. This paper investigates the cause-and-effect chain of cycle-to-cycle variation of spark ignition engines using 3D CFD simulations with CONVERGE v3.0. The cyclic variations were simulated through Large Eddy Simulations, and the simulations based on Reynolds-averaged Navier–Stokes were used as supplements. The analysis focuses on two key factors that determine the combustion process: the turbulent intensity and the homogeneity of the air/fuel mixture.

The European Union has defined legally binding CO2-fleet targets for new cars until 2030. Therefore, improvement of fuel economy and carbon dioxide emission reduction is becoming one of the most important issues for the car manufacturers. Today’s conventional car powertrain systems are reaching their technical limits and will not be able to meet future CO2 targets without further improvement in combustion efficiency, using low carbon fuels (LCF), and at least mild electrification. This paper demonstrates a highly efficient and performant combustion engine concept with a passive pre-chamber spark plug, operating at stoichiometric conditions and powered with liquefied petroleum gas (LPG). Even from fossil origin, LPG features many advantages such as low carbon/hydrogen ratio, low price and broad availability. In future, it can be produced from renewables and it is in liquid state under relatively low pressures, allowing the use of conventional injection and fuel supply components.

Pilot injection gas engines are commonly used as large stationary engines. Often, the combustion is implemented as a dual-fuel strategy, which allows both mixed and diesel-only operation, based on a diesel engine architecture. The current research project focuses on the application of pilot injection in an engine based on gasoline components of the passenger car segment, which are more cost-effective than diesel components. The investigated strategy does not aim for a diesel-only combustion, hence only small liquid quantities are used for the main purpose of providing a strong, reliable ignition source for the natural gas charge. This approach is mainly driven to provide a reliable alternative to the high spark ignition energies required for high cylinder charge densities. When using such small liquid quantities, a standard common-rail diesel nozzle will apparently not be ideal regarding some general specifications.

For scavenging the combustion chamber during the gas exchange, a temporary positive pressure gradient between the intake and the exhaust is required. On a single-scroll turbocharged four cylinder engine, the positive pressure gradient is not realized by the spatial separation of the exhaust manifold (twin-scroll), but by the use of suitable short exhaust valve opening times. In order to avoid any influence of the following firing cylinder onto the ongoing scavenging process, the valve opening time has to be shorter than 180 °CA. Such a short valve opening time has both, a strong influence on the gas exchange at the low-end torque and at the maximum engine power. This paper analyzes a phenomenon, which occurs due to short exhaust valve opening durations and late valve timings: A repeated compression of the burned cylinder charge after the bottom dead center, referred to as “recompression” in this paper.

The engine development process has been enhanced significantly by virtual engineering methods during the last decades. In terms of in-cylinder flow field, charge flow and combustion modelling, 3D-CFD (three dimensional) simulations enable detailed analysis and extended investigations in order to gain additional knowledge about design parameters. However, the computational time of the 3D-CFD is an obvious drawback that prevents a reasonable application for extensive analysis with varying speed, load and transient conditions. State-of-the-art 0D (zero dimensional) approaches close the gap between the demand of high computational efficiency and a satisfying accordance with experimental data. Recent improvements of phenomenological combustion approaches for gasoline spark ignition engines deal with the consideration of detailed flow parameters, the accuracy of the laminar flame speed calculation and the prediction of the knock limit.

Methane as an alternative fuel in motorsports? Actually this solution is well known for the reduction of CO₂ emissions but apparently it does not really awake race feelings. At the 2009 edition of the 24-hour endurance race on the Nürburgring the Volkswagen Motorsport GmbH, in addition to vehicles powered by gasoline engines, introduced two vehicles powered by innovative turbo-charged CNG engines for the first time. The aim was to prove, that also an "environment-friendly" concept is able to provide the required efficiency, dynamic and reliability for a successful participation in motorsports. After the success in the 2009 edition the engagement has been continued also in 2010, this time exclusively with CNG vehicles. Focusing on the CO₂ emission, reclusively the higher hydrogen content of methane which represents the main component of NG leads to a CO₂ reduction during the combustion of about 20% compared to gasoline.

There is a growing need for low-emissions concepts due to stricter emission regulations, more stringent homologation cycles, and the possibility of a ban on new engines by 2035. Of particular concern are the conditions during a cold start, when the Three-Way Catalyst is not yet heated to its light-off temperature. During this period, the catalyst remains inactive, thereby failing to convert pollutants. Reducing the time needed to reach this temperature is crucial to comply with the more stringent emissions standards. The post oxidation by means of secondary air injection, illustrated in this work, is a possible solution to reduce the time needed to reach the above-mentioned temperature. The strategy consists of injecting air into the exhaust manifold via secondary air injectors to oxidize unburned fuel that comes from a rich combustion within the cylinder.

The race towards zero carbon emissions is ongoing with the need to reduce the consumption of fossil energy resources. This demands immediate and reliable developments regarding technical environmentally friendly solutions for the power and transportation sectors. An alternative way to achieve a carbon-free powertrain is the use of green hydrogen for internal combustion engines. In this work the self-designed Fraunhofer single-cylinder engine with a displacement volume of 430 mm3 developed for extreme lean combustion and passive pre-chamber ignition was adapted for hydrogen engine operation. With hydrogen combustion, the customized cooling system resulting in low metal temperatures is simulated and optimized to avoid hot spots in the combustion chamber. The investigated single-cylinder engine is characterized by a compression ratio of 12.2, port fuel injection and a conventional spark plug.

As a promising concept to improve fuel efficiency of a long-haul heavy duty truck with diesel engine, organic Rankine cycle (ORC) based waste heat recovery system (WHR) by utilizing the exhaust gas from internal combustion engine has continuously drawn attention from industry in recent years. The greatest achievable global efficiency may be, however, restricted by the engine. On one hand, engine operating conditions have direct impact on the temperature and the mass flow of exhaust gas, which is the waste heat source, on the other hand, the engine cooling system limits the heat rejection from the condenser of the WHR system. This paper aims to evaluate the impacts of the varied engine applications considering the effects of the WHR system on the global efficiency and engine emissions.

Knocking is one of today’s main limitations in the ongoing efforts to increase efficiency and reduce emissions of spark-ignition engines. Especially for synthetic fuels or any alternative fuel type in general with a much steeper increase of the knock frequency at the KLSA, such as hydrogen, precise knock prediction is crucial to exploit their full potential. This paper therefore proposes a post-processing tool enabling further investigations to continuously gain better understanding of the knocking phenomenon. In this context, evaluation of local auto-ignitions preceding knock is crucial to improve knowledge about the stochastic occurrence of knock but also identify critical engine design to further optimize the geometry. In contrast to 0D simulations, 3D CFD simulations provide the possibility to investigate local parameters in the cylinder during the combustion.