Search Results

The feasibility of using experimentally determined flow fields at intake valve closing, IVC, as initial conditions for computing the in-cylinder flow dynamics during the compression stroke is demonstrated by means of a computer simulation of the overall approach. A commercial CFD code, STAR-CD, was used for this purpose. The study involved two steps. First, in order to establish a basis for comparison, the in-cylinder flow field throughout the intake and compression strokes, from intake valve opening, IVO, to top dead center, TDC, was computed for a simple engine geometry. Second, experimental initial conditions were simulated by randomly selecting and perturbing a set of velocity vectors from the computed flow field at IVC.

Gas carburized and quenched low alloy steels typically produce surface microstructures which contain martensite, retained austenite and often NMTP's (non-martensitic transformation products). The NMTP's are caused by a reduction of surface hardenability in the carburizing process from loss of alloying elements to oxidation. Gas carburized low alloy steels such as SAE 8620 with NMTP's on the surface have been shown to have inferior bending fatigue properties when compared to more highly alloyed steels which do not form NMTP's, such as SAE 4615M. One method of minimizing the formation of oxides and eliminating NMTP formation during carburizing and quenching is to use plasma carburizing instead of conventional gas carburizing. In this study the microstructures and bending fatigue performance of plasma carburized SAE 8620 and SAE 4615M is compared to the same alloys conventionally gas carburized and quenched.

Compositional and microstructural variations in a casting can often result in rather significant variations in the response to a given aging treatment, leading to location dependent mechanical properties. The objective of this study is to determine the effect of copper content and solidification rate on the aging behavior of a type 319 cast aluminum alloy. The nominal composition of the alloy is Al-7% Si-3.5% Cu-0.25% Mg, however, typical secondary 319 aluminum specifications allow copper levels to vary from 3-4%. Solidification rates throughout a casting can vary greatly due to, among other factors, differences in section size. To determine the effect of copper level and solidification rate on the aging response, aging curves were experimentally developed for this alloy. Three different copper levels (3, 3.5, 4%) and two solidification rates were used for this study. Aging temperatures ranged from 150-290°C with nine aging times at each temperature.

APPLICATIONS of nuclear energy in automotive manufacture have been made principally in the field of radioactivity. These are grouped under the following categories: radiography, nondestructive testing, gaging and control, tracer techniques, and static neutralizers. Radioactivity techniques are being used in foundry operations to check stock and metal levels in cupolas and distribution of element additives. In steel operations, these techniques are being used to check assimilation of ore-concentrate fines and thickness of rolled sheet steel. Other applications include measurement of pipe and wall thickness in pressure lines and engines, and inspection of castings and welds for internal faults. Radioactive techniques for improving processes, quality, and materials have potentially universal application. Greater industrial access to reactors will permit broader study and speed the development of new applications of radio-activity in industry.

Increased use of powder-forged connecting rods in the automotive industry prompted an investigation into the suitability of powders from different suppliers for this application. Specifications developed by North American users call for ultra clean powders to enhance machinability and fatigue life. Powders from four manufacturers were each blended with graphite and lubricant, then pressed, sintered and forged to full density. Metallographic samples were prepared and evaluated for inclusion content. In addition, the powders were mixed to the composition of connecting rods, (C - 0.5%, Cu - 2% and MnS - 0.3%), and were similarly pressed, sintered and forged. Test bars were machined from the forged discs. Uniaxial fatigue tests were performed in the tension-compression mode and strain-life curves were developed. It was determined that all powders examined were very clean and were comparable in their inclusion content.

AMONG the many outstanding advantages of the shell molding process of casting crankshafts, as described here, are the following: 1. Manner in which entire process responds to a high degree of automation. 2. Close tolerances that can be maintained from casting to casting. 3. Raw sand requirements are reduced from 125 lb (previous method) to 20 lb. 4. Results in 70% reduction in weight of chips produced. 5. Resulting crankshafts have highest wear resistance and exceptional endurance. 6. Gives additional design leeway: Allowing the most efficient distribution of weight. Contributing to engine compactness by varying the casting contour to prevent potential interferences.

There is a clearly demonstrated need to develop “real-time” methods for the measurement of diesel vehicle particulate emissions. Optical techniques provide One alternative for such methodology because of the rapid data acquisition times involved and the relatively simple sampling methods that can be used. This report describes two different approaches to this problem. The first, the spectrophone, measures light absorption by the diluted exhaust plume using photoacoustic spectroscopy, and the second, the long pathlength smokemeter, determines total light extinction across the diluted exhaust plume. For the measurement of total mass emissions, both techniques show estimated errors of ±15% for specific vehicles, while for a multi-vehicle diesel fleet the estimated errors are ±20% and ±30% for the long pathlength smokemeter and the spectrophone, respectively.

Rapid Prototyping, Fabrication and Tooling is a process that blends a series of technologies (machines, tools, and methods) capable of generating physical objects directly from a CAD database. The process dramatically reduces the time spent during product development by allowing for fast visualization, verification, iteration, optimization, and fabrication of parts and tools. Many new techniques of tooling have been and are being developed by using rapid fabricated parts. These are having a dramatic impact on both timing and costs throughout the automotive industry. One area that these methods can be utilized to their full potential is motorsports. Of particular interest is the growing use of bridge tooling to provide first article through production intent parts that promote cost effective changes.

Under a new program of quality control in the field of powder metallurgy automotive parts called quality assurance, the supplier is made a closer partner with the buyer to get a more dependable part that consistently meets all requirements and specifications. The quality assurance program consists of review of potential suppliers, contract negotiations, initial quality assurance surveys, and routine quality assurance surveys.

The constant challenge for automotive engineers to design vehicles with greater reliability at lower cost has brought powder metallurgy (P/M) to the foreground. This technology provides parts to or near net shape and results in savings of material, energy, capital equipment and floor space. This paper is an extension of SAE reports 850458 and 870133 and describes automotive powder metal components not previously identified. It should help engineers find cost effective applications early in the design stage so that P/M technology can be efficiently adopted. In addition, recent important technological developments in the P/M field applicable to automotive parts are highlighted. In particular, increased reliability achieved through SPC is stressed. A novel blending process is described whereby the alloying ingredients are “glued” to iron powder particles resulting in an increase in P/M quality through improved homogeneity.

The trend to production of near net shape components in the automotive industry and the constant crusade for cost reduction has brought powder metallurgy technology to the foreground. Savings of material, energy, manufacturing cost and the avoidance of capital expenditure are some of the principal benefits of this process. This paper is an extension of the previously published report. SAE 850458, which describes P/M components in the automobile. It also includes a new family of parts recently identified by the authors, i.e., sensors used in conjunction with electronics and microcomputers. In addition, progress made in recent years in P/M technology is summarized. This article is written for automotive design engineers to show various new applications of P/M and allow them to take advantage of the potential savings this technology offers.

In line with the present trend to make structural parts at or near net shape, the powder metallurgy process is being studied more and more by automotive design and materials engineers who are finding an increased application for this energy and cost saving process. Many new applications, besides some older ones, of P/M by domestic and overseas automotive manufacturers are presented outlining material specifications and service conditions for engine, transmission and chassis parts. In addition to conventional porous P/M parts, examples of high tensile fully dense precision hot formed P/M parts are presented which give superior service life and lighter weight than conventional wrought steel. Despite the decreased size and weight of future automobiles, an increased number of applications of powder metal is likely to result in a greater usage of P/M materials per vehicle.

Creep-resistant magnesium alloys for automotive powertrain applications offer significant potential for vehicle weight reduction. In this study permanent mold casting, microstructure and creep behavior have been investigated for a series of ternary magnesium alloys (Mg-4Al-4X (X: Ca, Ce, La, Sr) wt%) and AXJ530 (Mg-5Al-3Ca-0.15Sr, wt%). A permanent mold was instrumented with twelve thermocouples and mold temperature was monitored during the casting process. Average mold temperature increased from 200°C to 400°C during a typical alloy casting series (fifteen to twenty castings). The cast microstructure for all alloys consists of primary α-Mg globular phase surrounded by eutectic structure which is composed of intermetallic(s) and α-Mg magnesium phases. The primary cell size of the AXJ530 increased from 18 to 24 μm with increasing mold temperature and a similar trend is expected for all alloys.

Design optimization techniques are widely used to drive designs toward a global or a near global optimal solution. However, the achieved optimal solution often appears to be the only choice that an engineer/designer can select as the final design. This is caused by either problem topology or by the nature of optimization algorithms to converge quickly in local/global optimal or both. Problem topology can be unimodal or multimodal with many local and/or global optimal solutions. For multimodal problems, most global algorithms tend to exploit the global optimal solution quickly but at the same time leaving the engineer with only one choice of design. The paper explores the application of genetic algorithms (GA), simulated annealing (SA), and mixed integer problem sequential quadratic programming (MIPSQP) to find multiple local and global solutions using single objective optimization formulation.

The use of Shadowgraph and Schlieren optical systems is a simple method to determine flow patterns of heated air external to the vehicle at idle. In particular, the method can be used to visualize natural convective air flow patterns at the underbody to aid in heat shielding design. Moreover, air recirculation patterns around the front end of the vehicle can be visualized without the use of smoke. The optical equipment is described and recommendations proposed for setting up the equipment. A video tape of some results is also presented.

This paper benchmarks some methods of nondestructive testing for zero and high mileage spot weld quality/integrity and degradation evaluation (pin holes, voids, cracks, fatigue, corrosion, etc.). The methods include X-ray radiography, ultrasonic imaging, ultrasonic pulse/ echo, pulsed infrared or thermography, and laser/TV holographic interferometry imaging. The advantages and limitations of each method are provided with descriptive principles and real test examples. It is found that X-ray radiography combined with ultrasonic echo technique is the most favorable one considering time and cost for the current zero and high mileage spot weld evaluation.

This book draws upon a variety of the author's experiences during more than 25 years in automotive safety. It gives an introduction to plain film radiographs (x-rays), computed tomograms (CTs), and magnetic resonance images (MRIs) such that vehicle safety professionals can use these techniques to help piece together the puzzle and provide a better understanding of the relationship between vehicle crash scenarios and occupant injury. For those with a primarily vehicle background, Neck Injury provides an overview of how x-rays, CTs, and MRIs may be used as a source of information to help analyze vehicle crashes and the associated injuries. For those with a clinical background, the book provides insight into how injuries relate to the vehicle crash. Chapters cover: Anatomy Imaging Injuries and Injury Mechanisms

NODULAR cast iron, so called because the graphite is present as finely dispersed, well-rounded particles, is made in two stages: The first stage consists of the addition of magnesium or other carbide formers, which promote the formation of white iron in one normally solidifying gray. In the second stage a ferrosilicon type of inoculant overcomes the tendency toward white iron and causes the graphite to precipitate out in the form of small spherulites. The methods of making nodular iron, the effect of composition on physical properties, economic factors involved, and potential applications are discussed in this paper.

In modeling of engine fuel-air mixing, it is desired to be able to predict fuel spray atomization under different injection and ambient conditions. In this work, a previously developed sheet atomization model was studied for this purpose. For sprays from a pressure-swirl injector, it is assumed in the model that the fuel flows out the injector forming a conical liquid film (sheet), and the sprays are formed due to the disintegration of the sheet. Modified formulations are proposed to estimate sheet parameters including sheet thickness and velocity at the nozzle exit. It was found that the fuel flow rate of a swirl injector satisfied the correlation well. Computations of correlation well. Computations of the sprays injected in an engine with a side-mounted injector were performed for conditions that duplicated a set of experiments performed in an optical engine. The computed results were compared with the spray images obtained from the optical engine using elastic (Mie) scattering.

Magnesium alloy extrusions offer potentially more mass saving compared to magnesium castings. One of the tasks in the United States Automotive Materials Partnership (USAMP) ?Magnesium Front End Research and Development? (MFERD) project is to evaluate magnesium extrusion alloys AM30, AZ31 and AZ61 for automotive body applications. Solid and hollow sections were made by lowcost direct extrusion process. Mechanical properties in tension and compression were tested in extrusion, transverse and 45 degree directions. The tensile properties of the extrusion alloys in the extrusion direction are generally higher than those of conventional die cast alloys. However, significant tension-compression asymmetry and plastic anisotropy need to be understood and captured in the component design.