Search Results

The present production General Motors 2-Mode Hybrid system for full-size SUVs and pickup trucks integrates truck utility functions with a full hybrid system. The 2-mode hybrid system incorporates two electro-mechanical power-split operating modes with four fixed-gear ratios. The combination provides fuel savings from electric assist, regenerative braking and low-speed electric vehicle operation. The combination of two power-split modes reduces the amount of mechanical power that is converted to electric power for continuously variable transmission operation, meeting the utility required for SUVs and trucks. This paper describes how fuel economy functionality was blended with full-size truck utility functions. Truck functions described include: Manual Range Select, Cruise Control, 4WD-Low and continuous high load operation.

A detailed description of a numerical method for computing unsteady flows in engine intake and exhaust systems is given. The calculations include the effects of heat transfer and friction. The inclusion of such calculations in a mathematically simulated engine cycle is discussed and results shown for several systems. In particular, the effects of bell-mouth versus plain pipe terminations and the effects of a finite surge tank are calculated. Experimental data on the effect of heat transfer from the back of the intake valve on wave damping are given and show the effect to be negligible. Experimental data on wave damping during the valve closed period and on the temperature rise of the air near the valve are also given.

The ratio of two temperature gradients across the combustion-chamber wall in a diesel engine is used to provide a heat flow ratio showing the radiant heat transfer as a per cent of local total heat transfer. The temperature gradients were obtained with a thermocouple junction on each side of the combustion-chamber wall. The first temperature gradient was obtained by covering the thermocouple at the cylinder gas-wall interface with a thin sapphire window, while the second was obtained without the window. Results show that the time-average radiant heat transfer is of significant magnitude in a diesel engine, and is probably even more significant in heat transfer during combustion and expansion.

The objective of this research was to investigate the effect of injection pressure on air entrainment into transient diesel sprays. The main application of interest was the direct injection diesel engine. Particle Image Velocimetry was used to make measurements of the air entrainment velocities into a spray plume as a function of time and space. A hydraulically actuated, electronically controlled unit injector (HEUI) system was used to supply the fuel into a pressurized spray chamber. The gas chamber density was maintained at 27 kg/m3. The injection pressures that were studied in this current research project were 117.6 MPa and 132.3 MPa. For different injection pressures, during the initial two-thirds of the spray plume there was little difference in the velocities normal to the spray surface. For the last third of the spray plume, the normal velocities were 125% higher for the high injection pressure case.

Distracted driving remains a serious risk to motorists in the US and worldwide. Over 3,000 people were killed in 2013 in the US because of distracted driving; and over 420,000 people were injured. A system that can accurately detect distracted driving would potentially be able to alert drivers, bringing their attention back to the primary driving task and potentially saving lives. This paper documents an effort to develop an algorithm that can detect visual distraction using vehicle-based sensor signals such as steering wheel inputs and lane position. Additionally, the vehicle-based algorithm is compared with a version that includes driving-based signals in the form of head tracking data. The algorithms were developed using machine learning techniques and combine a Random Forest model for instantaneous detection with a Hidden Markov model for time series predictions.

Sound power can be determined using a variety of methods, but precision methods require the volume of the noise source to be less than 1% of the chamber volume leading to relatively large test chambers. Automotive torque converter performance and noise testing is completed in an enclosed metallic test fixture which inhibits the use of precision methods due to volume and space limitations. This paper describes a new method developed to accurately determine sound power of an automotive torque converter in a relatively small enclosure through characterization of the test environment. The test environment was characterized using two reference noise sources designed to represent torque converter noise output and physical geometry. Sound pressure levels of the sources were measured at multiple microphone locations and at three source amplitude levels to characterize the environment.

This paper describes how distributive computing along with statistical subsystem simulation can be applied to produce near production ready embedded vehicle software and calibrations. Coupling distributive computing and statistical simulation was first employed over a decade ago at General Motors to design and analyze propulsion subsystem hardware. Recently this method of simulation has been enhanced extending its capabilities to both test embedded vehicle code as well as develop calibrations. A primary advantage of this simulation technique is its ability to generate data from a statistically significant population of subsystems. The result is the acquisition of an optimal data set enabling the development of a robust design now including both embedded code and calibrations. Additionally it has been shown that there are significant economic advantages in terms of time and cost associated with this type of development when compared to traditional method.

A detailed mathematical model of the thermodynamic events of a crankcase scavenged, two-stroke, SI engine is described. The engine is divided into three thermodynamic systems: the cylinder gases, the crankcase gases, and the inlet system gases. Energy balances, mass continuity equations, the ideal gas law, and thermodynamic property relationships are combined to give a set of coupled ordinary differential equations which describe the thermodynamic states encountered by the systems of the engine during one cycle of operation. A computer program is used to integrate the equations, starting with estimated initial thermodynamic conditions and estimated metal surface temperatures. The program iterates the cycle, adjusting the initial estimates, until the final conditions agree with the beginning conditions, that is, until a cycle results.

This work reports a CFD study on a 2-stroke (2-S) opposed piston high speed direct injection (HSDI) Diesel engine. The engine main features (bore, stroke, port timings, et cetera) are defined in a previous stage of the project, while the current analysis is focused on the assembly made up of scavenge ports, manifold and cylinder. The first step of the study consists in the construction of a parametric mesh on a simplified geometry. Two geometric parameters and three different operating conditions are considered. A CFD-3D simulation by using a customized version of the KIVA-4 code is performed on a set of 243 different cases, sweeping all the most interesting combinations of geometric parameters and operating conditions. The post-processing of this huge amount of data allow us to define the most effective geometric configuration, named baseline.

The purpose of this paper is to present the origins and the technology of the different types of non-manual transmissions systems currently available and the wide potential to incorporate such technologies to the vehicles made in Brazil. The Brazilian market is experiencing a huge increase in automated and automatic transmissions vehicles share, and the OEMs are adopting different strategies to offer competitive products with affordable prices to enter in this segment. Many different alternatives are available, and there is no obvious winner. This paper will describe the concepts, the architecture and the operations of such systems and point out the pros and cons of each one.

Highly time resolved measurements of cylinder pressure acquired simultaneously from three transducers were used to investigate the nature of knocking combustion and to identify biases that the pressure measurements induce. It was shown by investigating the magnitude squared coherence (MSC) between the transducer signals that frequency content above approximately 40 kHz does not originate from a common source, i.e., it originates from noise sources. The major source of noise at higher frequency is the natural frequency of the transducer that is excited by the impulsive knock event; even if the natural frequency is above the sampling frequency it can affect the measurements by aliasing. The MSC analysis suggests that 40 kHz is the appropriate cutoff frequency for low-pass filtering the pressure signal. Knowing this, one can isolate the knock event from noise more accurately.

To meet future world energy demands, the engineer’s task will be to develop, through research, means of supplying new sources of energy. Though nuclear processes and solar energy will provide future energy, they are not readily adaptable to portable power systems due to inherent shortcomings. Energy can be supplied to portable power systems by energy storage systems using chemical, mechanical, or electrical forms, or it may be supplied through energy-in-transit systems. Technical discussion of various systems is presented. To develop suitable energy storage systems, thought must be given to problems of construction, operation, maintenance, and economics. Research is necessary to determine which chemical fuels are most adaptable for internal combustion engines.

Low Voltage Electric Drives are becoming very attractive for various applications in the Turf, Construction and Agricultural products being engineered today. Determining what the Customer Support Requirements are for Maintenance and Repair for the Life Cycle of the products is critical to the initial design process. Presenter Russell Christ

With the ability of modern high pressure diesel injectors to deliver accurate, closely coupled multiple pulse injections, it is possible to minimize engine combustion noise without negative effect on exhaust emissions. Literature shows that, splitting the cycle heat release into several parts helps to lower peak heat release rate and combustion noise. The charge cooling caused by fuel vaporization can be effectively used to influence ignition delay and achieve lower noise, emissions and fuel consumption. With the traditional pilot-main injection scheme, researchers have shown that, the injection dwell time between the pilot and main is primarily responsible for noise reduction. The current objective is to analytically explore the fundamental physics behind the experimentally observed noise reduction phenomena with multiple injections. This computational study was conducted at a key part-load operation (2000RPM and 5Bar BMEP) with five injection pulses.

The effects of imaging system resolution and laser sheet thickness on the measurement of the Batchelor scale were investigated in a single-cylinder optical engine. The Batchelor scale was determined by fitting a model spectrum to the dissipation spectrum that was obtained from fuel tracer planar laser-induced fluorescence (PLIF) images of the in-cylinder scalar field. The imaging system resolution was quantified by measuring the step-response function; the scanning knife edge technique was used to measure the 10-90% clip width of the laser sheet. In these experiments, the spatial resolution varied from a native resolution of 32.0 μm to 137.4 μm, and the laser sheet thickness ranged from 108 μm to 707 μm. Thus, the overall resolution of the imaging system was made to vary by approximately a factor of four in the in-plane dimension and a factor of six in the out-of-plane dimension.

A computational, three-dimensional approach to investigate the behavior of diesel soot particles in the micro-channels of wall-flow Diesel Particulate Filters is presented. The KIVA3V CFD code, already extended to solve the 2D conservation equations for porous media materials [1], has been enhanced to solve in 2-D and 3-D the governing equations for reacting and compressible flows through porous media in non axes-symmetric geometries. With respect to previous work [1], a different mathematical approach has been followed in the implementation of the numerical solver for porous media, in order to achieve a faster convergency as source terms were added to the governing equations. The Darcy pressure drop has been included in the Navier-Stokes equations and the energy equation has been extended to account for the thermal exchange between the gas flow and the porous wall.

3-D Computational Fluid Dynamics (CFD) simulations have been performed to study particulate formation in a Spark-Ignition (SI) engine under premixed conditions. A semi-detailed soot model and a chemical kinetic model, including poly-aromatic hydrocarbon (PAH) formation, were coupled with a spark ignition model and the G equation flame propagation model for SI engine simulations and for predictions of soot mass and particulate number density. The simulation results for in-cylinder pressure and particle size distribution (PSDs) are compared to available experimental studies of equivalence ratio effects during premixed operation. Good predictions are observed with regard to cylinder pressure, combustion phasing and engine load. Qualitative agreements of in-cylinder particle distributions were also obtained and the results are helpful to understand particulate formation processes.

Using a clutch to disconnect and shut-off the engine when engine power is not required, the single-motor strong hybrid has the potential for significant fuel economy improvement with reduced costs and less system complexity. However, it is a challenge for the single-motor strong hybrid to maintain acceptable drivability at engine start since it requires diverting motor torque through a slipping clutch to start the engine. In this study, dynamic simulations of the hybrid transmission driveline with hydraulic and motor controls have been employed to assess the feasibility of the single-motor strong hybrid, to address drivability issues specific to this hybrid architecture at engine start, and to develop control methods to manage driveline disturbances to an acceptable level.

High interest is expressed in using analytical models to eliminate costly driveline tests used to determine the stresses produced in the driveshaft and driveline during resonant operating conditions. This paper discusses an analytical model to simulate the driveline-bending integrity, test procedure. Three major subsystems are modeled in this analytical approach, namely powertrain, rear axle, and driveshaft. Imbalance masses were added on the driveshaft to induce the whirl motion of the driveshaft. The combination of nonlinear Multi-body System Simulation (MSS) and linear Finite Element Analysis (FEA) in the time domain was employed for the evaluation of the dynamic interaction between several parts.

This paper reports the mass-burning rate in a rotary combustion engine. The mass-burning rate is calculated through an iterative constituent and energy constraints during the combustion process. First approximation is obtained through the firing and motoring-pressure trace as recorded by an image-retaining oscilloscope and recorded subsequently by a polaroid camera. Effect of engine load, engine speed, relative (A/F) on the mass-burning rate and maximum heat release rate were studied. Three different type of fuels were used in the experimental test runs.