Search Results

The concept of product or system function is considered as described in the Taguchi System of Quality Engineering. The importance of transfer functions is also discussed and a review of conventional value analysis techniques is given. This paper proposes a combination of the principles of robust design and value methodology to enable on-target functionality and direct cost allocation early in the product development process. The discussion on integration of value analysis principles in robust design methodology is provided considering the six sigma environment.

Since 1985, the Body Division of the Automotive Corrosion and Prevention Committee of SAE (ACAP) has conducted biannual surveys of automotive body corrosion in the Detroit area. The purpose of these surveys is to track industry wide corrosion protection improvements and to make this information available for public consumption. The survey consists of a closed car parking lot survey checking for perforations, blisters, and surface rust. This paper reports the results of the five surveys conducted to date.

Future automobiles are required to support an increasing number of complex, distributed functions such as active safety and X-by-wire. Because of safety concerns and the need to deliver correct designs in a short time, system properties should be verified in advance on function models, by simulation or model checking. To ensure that the properties still hold for the final deployed system, the implementation of the models into tasks and communication messages should preserve properties of the model, or in general, its semantics. FlexRay offers the possibility of deterministic communication and can be used to define distributed implementations that are provably equivalent to synchronous reactive models like those created from Simulink. However, the low level communication layers and the FlexRay schedule must be carefully designed to ensure the preservation of communication flows and functional outputs.

For the assessment of vehicle acoustics in the early design stages of a vehicle program, the use of full vehicle SEA models is becoming the standard analysis method in the US automotive industry. One benefit is that OEM's and Tier 1 suppliers are able to cascade lower level acoustic performance targets for NVH systems and components. Detailed SEA system level models can be used to assess the performance of systems such as dash panels, floors and doors, however, the results will be questionable until test data Is available. Correlation can be accomplished with buck testing, which is a common practice in the automotive industry for assessing the STL (sound transmission loss) of vehicle level components. The opportunity to conduct buck testing can be limited by the availability of representative bodies to be cut into bucks and the availability of a transmission loss suite with a suitably large opening.

This paper deals with a conceptual aircraft cargo loader “that can do everything” commonly referred to as The Super Loader. The Super Loader is intended for use at air terminals to transport loads such as palletized cargo, containers, wheeled vehicles, shelters, and airdrop platforms from the storage docks to the military and civil aircraft, and vice versa. The loader may be described as a self-propelled, air transportable (in a C-141, C-17, C-5) 60,000 lb lifting capacity, adjustable height vehicle that will load/off load all transport aircraft from a C-130 whose cargo deck is only 3 feet, 3 inches high to a B-747 whose main deck upper limit is about 18 feet high. The Super Loader must also service the lower lobes of wide-bodies and main decks of narrow-bodied aircraft like the DC-8 and B-707. In brief, this loader will be required to interface with both civil and military cargo systems, present and future.

A brief overview of the history and scope of the SAE Oil Labeling Assessment Program is presented. Then, the results of analyses on 893 samples of engine oil purchased in the retail market over the first three years of the program, are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API “C” category designation. Additionally, 43 engine oil samples found to be questionably labeled, were repurchased and analyzed; these results are included.

The results of analyses on 300 samples of engine oil purchased in the retail market in 1990 are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API C category designation. Also, 17 oils previously found to be questionably labeled, from the 1989 set, were repurchased and analyzed. These results are included.

Relative velocity detection thresholds of drivers are one factor that determines their ability to avoid rear-end crashes. Laboratory, simulator and driving studies show that drivers could scale relative velocity when it exceeded the threshold of about 0.003 rad/sec. Studies using accident reconstruction have suggested that the threshold may be about ten times larger. This paper discusses this divergence and suggests reasons for it and concludes that the lower value should be used as a true measure of the psychological threshold for detection of relative velocity.

A new form of SAE Transactions has been developed which allows for considerable flexibility in format, content, and distribution. A key volume includes abstracts of all SAE papers and a comprehensive depth index. Optional additions include printed and bound sets of all Transactions papers in full, subscriptions for all SAE papers, subscriptions for all SAE Transactions papers, and microfiche versions of each of these. No longer limited by physical size, all worthy papers can now be included in Transactions together with discussion, thereby enlarging the scope of Transactions approximately seven times.

The so-called Modified Martempering discussed in this work differs from the standard martempering by that the temperature of the quenching bath is below the Ms point. In spite of the fact the lower temperature increases the severity of quenching, this also usually avoids the bainite formation, and by this reason, it is possible to make a fair comparison between different processes, which result in different microstructures. The present study shows the results in terms of mechanical properties, impact resistance in special of a cold work tool steel class, after being heat treated by the isothermal modified martempering process, as well as a comparison with the conventional quenching and tempering process and the austempering as well.

A review of many years of published work has shown that hydrogen embrittlement can occur under rolling contact conditions. Breakdown of lubrication and contamination with water have been cited as the probable sources of atomic hydrogen. In this paper, a unique fracture morphology is identified and the mechanism of the fracture progression from initiation to final catastrophic failure is proposed. Development of beneficial residual compressive stress near the contacting surfaces is one approach used to avoid this type of failure. Several alternative methods capable of developing a more desirable stress distribution will be discussed.

The introduction of MultiAir technology [8] has had a strong impact on engine performance, fuel consumption, emissions and control. This technology, intended at first for gasoline engines and applied only on intake valves, is aiming at the reduction of engine breathing losses and, as a consequence, reduction of pollutant emissions and fuel consumption, together with an improvement of maximum intake efficiency. Further positive effects of MultiAir technology have been a significant improvement of Low End Torque, engine driveability (“fun-to-drive” index) and other operating conditions (e.g. idle control). Current development of MultiAir technology is focusing on a better management of hot EGR (Exhaust Gas Recirculation), still acting only on the intake side, although with specifically designed valve lift profiles. This application of MultiAir technology is pushing gasoline engines towards new levels of performance improvements.

It has the aim to discuss the evolution of electronics components, integrated circuits, new transistors concepts and associate its importance in the automotive modules. Today, the challenge is to have devices which consume less power, suitable for high-energy radiation environment, less parasitic capacitances, high speed, easier device isolation, high gain, easier scale-down of threshold voltage, no latch-up and higher integration density. The improvement of those characteristics mentioned and others in the electronic devices enable the automotive industry to have a more robust product and give the possibility to integrate new features in comfort, safety, infotainment and telematics modules. Finally, the intention is to discuss advanced structures, such as the silicon-on-insulator (SOI) and show how it affects the electronics modules applied for the automotive area.

This study applies the methodology developed for two earlier evaluations of diesel particulate controls to urban buses. Since these vehicles are used almost exclusively in urban areas where population is most dense, the analysis indicates the net benefits of control are very high.

Quasi-static tensile properties of TRIP590 steels from three different manufacturers were investigated using digital image correlation (DIC). The focus was on the post-uniform elongation behavior which can be very different for steels of the same grade owing to different manufacturing processes. Miniature tensile specimens, cut at 0°, 45°, and 90° relative to the rolling direction, were strained to failure in an instrumented tensile stage. True stress-true strain curves were computed from digital strain gages superimposed on digital images captured from one gage section surface during tensile deformation. Microstructural phases in undeformed and fracture specimens were identified with optical microscopy using the color tint etching process. Fracture surface analyses conducted with scanning electron microscopy and energy dispersive spectroscopy were used to investigate microvoids and inclusions in all materials.

Currently, OEMs worldwide are emphasizing more upon development and implementation of new electrical features on existing vehicles [3]. However, development and implementation of new electrical features on existing vehicle platforms create architectural as well as packaging challenges. These challenges are augmented due to following: the need to implement such features across different body styles of vehicles that are based on same or different architectures different requirement for a feature based upon market requirement This paper analyzes these challenges to help in providing design solutions for successful implementation of new features as per following requirements: 1 Provide optimum design to have low cost and high quality for existing vehicle platforms 2 Provide spare capacity while designing new vehicles or architectures

Multiple automotive applications exist for small electric motors that are activated by vehicle occupants for various functions such as window lifts and seat adjusters. For such a motor to be described as high quality, not only should the sound it produces be low in amplitude, but it also needs to be free from pulsations and variations that might occur during its (otherwise) steady-state operation. If a motor’s sound contains pulsations or variations between 2 and 8 cycles per second, the variation is described as warble. To establish performance targets for warble noise at both the vehicle and component level a way to measure and quantify the warble noise must be established. Building on existing sound quality metrics such as loudness and pitch variation, a method is established by which processed sound data is put through a secondary operation of Fourier analysis.

A hybrid electric vehicle simulation tool (IBZ-Simulator) has been developed at the Fuel Cell Institute of the University of Applied Sciences Esslingen to study the fuel economy potential of a Fuel Cell hybrid urban bus. In this paper, the fundamental architecture of the FC urban buses was described, as well as the control strategy to manage the power flow between the different elements of the drive train. A comparison of the hybrid with the conventional type and ICE-hybrid type is performed, and important factors relating to the vehicle efficiency (accessory loads, vehicle mass, Fuel Cell system ramping rate and battery capacity) were assessed. The using of supercapacitor (or ultracapacitors) as peak power buffer has been investigated.

Multi-layered, high-density polyethylene (HDPE) fuel tanks are increasingly being used in automobiles due to advantages such as shape flexibility, low weight and corrosion resistance. Though, HDPE fuel tanks are perceived to be safer as compared to metallic tanks, the material properties are influenced by service temperature. At higher temperatures (more than 80oC), plastic fuel tanks can soften, sag and eventually spill out the fuel, while the extreme cold (less than -20°C) can lead to potential cracking problems. Damage may also occur due to accidental drop while handling or due to an impact from a flying shrapnel. This can be catastrophic due to flammability of the fuel. The objective of this work is to characterize and develop a failure model for the plastic fuel tank material to simulate damage and enhance predictive capability of CAE for chassis and safety load cases.

Shared Mobility is changing mobility trends of Automotive Industry and its one of the Disruptions. The current vehicle customer usage and life of components are designed majorly for personal vehicle and with factors that comprehend usage of shared vehicles. The usage pattern for customer differ between personal vehicle, shared vehicle & Taxi. In the era of Autonomous and Shared mobility systems, the customer usage and expectation of vehicle condition on each & every ride of vehicle will be a vehicle in good condition on each ride. The vehicle needs systems that will guide or fix the issues on its own, to improve customer satisfaction. We also need a transformation in customer behavior pattern to use shared mobility vehicle as their personal vehicle to improve the life of vehicle hardwares & reduce warranty cost. We will be focusing on Vehicle Closure hardware & mechanisms as that will be the first and major interaction point for customers in vehicle.