Search Results

Twent-two participants of varying ages detected roadside targets in two consecutive dynamic evaluations of a horizontally swiveling headlamp vehicle and a vehicle with the same headlamps that did not swivel. Participants detected targets as they drove unlighted low-speed public roads. Scenarios encountered were intersection turns, and curves with approximate radii of 70-90m, 120-140m, 170-190m, and 215-220m. Results from the first study found improved detection distances from the swiveling headlamps in left curves, but unexpectedly decreased detection distances in larger radius right hand curves. The swiveling algorithm was altered for the second study, and the headlamps used did not have the same beam pattern as in the first study. Results from the second study again found improved detection distances from the swiveling headlamps while in the larger radius right hand curves fixed and swivel were not statistically different.

The increased demands of today's complex automotive connector designs have led to the development of engineering structural analysis tools which address the performance issues of the connector's snap-finger. In designs where hand calculations were once considered the norm in evaluating snap-finger performance, the analysis tools have evolved into the use of finite element techniques which address the high nonlinearity issues of snap-finger disassembly and terminal pull out strength. The structural analysis approaches developed investigate the connector snap-finger performance in reinforced engineering thermoplastics while incorporating the effects of geometric and material nonlinearity in the results. The techniques developed allow for the evaluation of snap-finger performance of prospective connector designs before expensive tooling and prototyping is initiated, providing the benefits of limited tool rework and decreased product development time.

A previously developed finite element human head/cervical spine model was further enhanced to include the major muscles in the neck. The head/cervical spine model consists of the skull, C1-C7, disks, facets, and all the ligaments in this region. The vertebral bodies are simulated by deformable bodies and the soft tissues in the cervical spine are modeled by nonlinear anisotropic viscoelastic material. The motion segments in the cervical spine model were validated against three-dimensional cadaver test data reported in the literature. To simulate the passive and active muscle properties, the classical Hill muscle model was implemented in the LS-DYNA code and model parameters were based on measurements of cadaver neck musculature. The head/neck model was used to simulate a human volunteer flexion whiplash test reported in the literature. Simulation results showed that the neck muscle contraction and relaxation activities had a significant effect on the head/neck motion.

In practice, the piston wrist pin is either fixed to the connecting rod or floats between the connecting rod and the piston. The tribological behavior of fixed wrist pins have been studied by several researchers, however there have been few studies done on the floating wrist pin. A new bench rig has been designed and constructed to investigate the tribological behavior between floating pins and pin bore bearings. The experiments were run using both fixed pins and floating pins under the same working conditions. It was found that for fixed pins there was severe damage on the pin bore in a very short time (5 minutes) and material transfer occurs between the wrist pin and pin bore; however, for the floating pin, even after a long testing time (60 minutes) there was minimal surface damage on either the pin bore or wrist pin.

This paper presents results from a series of tests that address safety related issues concerning vehicle glazing. These issues include occupant containment, head impact injury, neck injuries, fracture modes, and laceration. Component-level and full vehicle crash tests of standard and polycarbonate non-windshield glazing were conducted. The tests were conducted as part of a study to demonstrate that there is no decrease in the safety benefits offered by polycarbonate glazing when compared to current glazing. Readers of this paper will gain a broader understanding of the tests that are typically conducted for glazing evaluation from a safety perspective, as well as gain insight into the meaning of the results.

This paper discusses radio usage habits observed during analysis of 700 hours of video sampled from the 100-Car Naturalistic Driving Study database. Analysts used large-scale printouts of each vehicle's radio faceplate and recorded interactions based on video analysis of hand movement and location (without the assistance of audio recordings). The duration and specific manipulations or adjustments were recorded for each interaction. The results summarize the length and type of interactions, most often-used controls, and total percentage of time drivers interacted with the radio.

A technique for estimating the lateral loads exerted on the vehicle frame during centerline pendulum impacts has been developed. These loads can either be determined by sophisticated hand calculations or by using beam finite-element analysis. The loads can either be determined as a fraction of the peak impact load, or as an absolute number. The dependence of the lateral load on frame stiffness, bumper cross-section, and bumper sweep will be shown to be quite dramatic.

This paper will describe an approach to satisfying proposed European Enhanced Vehicle Safety Committee (EEVC) legislation for lower leg pedestrian impact. The solution for lower leg protection is achieved through a combination of material properties and design. Using Computer Aided Engineering (CAE) modeling, the performance of an energy absorber (EA) concept was analyzed for knee bending angle, knee shear displacement, and tibia acceleration. The modeling approach presented here includes a sensitivity analysis to first identify key material and geometric parameters, followed by an optimization process to create a functional design. Results demonstrate how an EA system designed with a polycarbonate/polybutyelene terephthalate (PC/PBT) resin blend, as illustrated in Figure 1, can meet proposed pedestrian safety requirements.

This paper describes a bumper system designed to meet the current FMVSS (Federal Motor Vehicle Safety Standard) and ECE42 legislation as well as the European Enhanced Vehicle Safety Committee (EEVC) requirements for lower leg pedestrian impact protection [1] (The EEVC was founded in 1970 in response to the US Department of Transportation's initiative for an international program on Experimental Safety Vehicles. The EEVC steering committee, consisting of representatives from several European Nations, initiates research work in a number of automotive working areas. These research tasks are carried out by a number of specialist Working Groups who operate for over a period of several years giving advice to the Steering Committee who then, in collaboration with other governmental bodies, recommends future courses of action designed to lead to improved safety in vehicles).

An interactive tool for predicting the performance of vehicle designs in the pedestrian leg impact test has been developed. This tool allows users to modify the design of a vehicle front structure through the use of a graphical interface, and then evaluates the performance of the design with a response surface. This performance is displayed in the graphical interface, providing the user with nearly instantaneous feedback to his design changes. An example is shown that demonstrates how the tool can be used to help guide the user towards vehicle designs that are likely to improve performance. As part of the development of this tool, a simplified, parametric finite element model of the front structure of the vehicle was created. This vehicle model included eleven parameters that could be adjusted to change the structural dimensions and structural behavior of the model.