Search Results

TWO TYPES of bench wear tests employed by the General Motors Research Laboratories are described, and examples are given to illustrate the application of the tests to material development problems. It is shown that correlation of a bench test with service may be achieved even when the laboratory test conditions do not appear to duplicate service conditions exactly. It is postulated that this behaviour is related to the formation of certain types of surface films during the wearing process. Some preliminary results are given of a study of the influence of lubricant type and material composition on the formation of anti-wear films.

THE automotive and petroleum industries have been concerned for many years with the mutual problem of improving the thermal efficiency of gasoline engines. Great progress in refining technology, as well as advances in engine design in recent years, have made it desirable to take a new look at high-compression engines. This paper describes an investigation of the effect of compression ratio on engine efficiency over a range of compression ratios from 9/1 to 25/1. The results show that the thermal efficiency of the multicylinder engines used in this study peaked at a compression ratio of 17/1. The decrease in thermal efficiency at higher compression ratios is due primarily to delay in the completion of the combustion process. This paper received the 1958 Horning Memorial Award.

Four multigrade engine oils, containing the same base oil plus SE additive package but VI improvers of differing shear stability, were evaluated in 80 000 km of high-speed, high-temperature vehicle service. Bearing, piston ring and valve guide wear, as well as oil consumption, oil filter plugging and engine cleanliness were all worse for the engines operated on the low-shear stability oils. The wear differences were traced to differences in high-shear-rate viscosity, while the cleanliness, filter plugging and oil consumption differences occurred because of excessive wear or polymer shear degradation. These results suggest that engine oil viscosity should be specified under high-shear-rate conditions.

Aqua-ammonia absorption refrigeration cycle and R-134a Vapor jet-ejector refrigeration cycle for automotive air-conditioning were studied and analyzed. Thermally activated refrigeration cycles would utilize combustion engine exhaust gas or engine coolant to supply heat to the generator. For the absorption system, the thermodynamic cycle was analyzed and pressures, temperatures, concentrations, enthalpies, and mass flow rates at every point were computed based on input parameters simulate practical operating conditions of vehicles. Then, heat addition to the generator, heat removal rates from absorber, condenser, and rectifying unit, and total rejection heat transfer area were all calculated. For the jet-ejector system, the optimum ejector vapor mass ratio based on similar input parameters was found by solving diffuser's conservation equations of continuity, momentum, energy, and flow through primary ejector nozzle simultaneously.

The more noise and vibration improvements are incorporated into our vehicles, the more customers notice squeaks and rattles (S&R). Customers increasingly perceive S&R as a direct indicator of vehicle build quality and durability. The high profile nature of S&R has the automotive industry striving to develop the understanding and technology of how to improve the S&R performance in the vehicle. Squeaks and itches make up a significant amount of Squeak and Rattle complaints found in today's vehicles. Squeaks and itches are the result of stick slip behavior between two interacting surfaces. Squeak itch behavior is dependent upon a large number of parameters including but not limited to: the material itself, temperature, humidity, normal load, system compliance, part geometry, velocity, surface roughness, wear, contaminants, etc. This paper will describe the analysis of sound data and friction data and the relationship between them.

The development of a plasma jet ignition system is described on a 4-cyl, 140 in3 engine. Performance was evaluated on the basis of combustion flame photographs in a single-cylinder engine at 20/1 A/F dynamometer tests on a modified 4-cyl engine, and cold start emissions, fuel economy, and drivability in a vehicle at 19/1 air fuel ratio. In addition to adjustable engine variables such as air-fuel ratio and spark advance, system electrical and mechanical parameters were varied to improve combustion of lean mixtures. As examples, the air-fuel ratio range was 16-22/1, secondary ignition current was varied from 40 to 6000 mA, and plasma jet cavity and electrode geometry were optimized. It is shown that the plasma jet produces on ignition source which penetrates the mixture ahead of the initial flame front and reduces oxides of nitrogen emission, in comparison to a conventional production combustion chamber.

Homogenous Charge Compression Ignition (HCCI) combustion offers significant efficiency improvements compared to conventional gasoline engines. However, due to the nature of HCCI combustion, traditional HCCI engines show some degree of sensitivity to in-cylinder thermal conditions; thus higher cylinder-to-cylinder variation was observed especially at low load and high load operating conditions due to different injector characteristics, different amount of reforming as well as non-uniform EGR distribution. To address these issues, a cylinder balancing control strategy was developed for a multi-cylinder engine. In particular, the cylinder balancing control strategy balances CA50 and AF ratio at high load and low load conditions, respectively. Combustion noise was significantly reduced at high load while combustion stability was improved at low load with the cylinder balancing control.

From November 1970 through August 1971 an extensive program of static and dynamic air cushion inflation tests utilizing human volunteers was conducted at Holloman Air Force Base, New Mexico, sponsored by the Department of Transportation. Forty-one full cushion deployment static firings were made, with air cushion hardware and seating buck environment designed by General Motors. The static series was followed by 35 dynamic sled firings of human volunteers, beginning at 8.6 g (15.1 mph) and culminating at 21.7 g (31.5 mph). A major objective of both the static and dynamic test series was to identify changes in air-cushion design found necessary to improve its protective capability for human beings. Because of the severity of cushion deployment, one modification was made following the initial static tests: The orifice diameter size of the bag inlet was reduced from 1.0 to 0.6 in to diminish the rapidity of bag inflation. This modification proved effective in the dynamic series.

The level of filtration in an engine can have a significant impact on wear rates due to abrasive particles. Tests were conducted to establish a relationship between the level of filtration and abrasive engine wear. Although the tests were run in a laboratory environment, wear was reduced by as much as 70% by going from a 40 micron filter to a 15 micron filter. Testing was performed on a heavy duty diesel engine and later with an automotive gasoline engine. The results from both engines were consistent and showed that the relationship developed can be applied to nearly any internal combustion recipricating engine.

A spectroscopic diagnostic system was designed to study the effects of different engine parameters on the chemiluminescence characteristic of HCCI combustion. The engine parameters studied in this work were intake temperature, fuel delivery method, fueling rate (load), air-fuel ratio, and the effect of partial fuel reforming due to intake charge preheating. At each data point, a set of time-resolved spectra were obtained along with the cylinder pressure and exhaust emissions data. It was determined that different engine parameters affect the ignition timing of HCCI combustion without altering the reaction pathways of the fuel after the combustion has started. The chemiluminescence spectra of HCCI combustion appear as several distinct peaks corresponding to emission from CHO, HCHO, CH, and OH superimposed on top of a CO-O continuum. A strong correlation was found between the chemiluminescence light intensity and the rate of heat release.

This paper describes a test of 2500 General Motors passenger cars equipped with anti-lacerative windshields and driven in rental fleets. It also de840391 scribes the laboratory tests conducted prior to the fleet installation of the test windshields. Evaluation of haze development caused by abrasion of the anti-lacerative surface will take several more years of exposure. Other test results have been encouraging, except for the difficulties encountered in the removal of stickers and decals from the inner surface.

Contamination protection of brake rotors has been a challenge for the auto industry for a long time. As contamination of a rotor causes corrosion, and that in turn causes many issues like pulsation and excessive wear of rotors and linings, a rotor splash protection shield became a common part for most vehicles. While the rotor splash shield provides contamination protection for the brake rotor, it makes brake cooling performance worse because it blocks air reaching the brake rotor. Therefore, balancing between contamination protection and enabling brake cooling has become a key critical factor when the splash shield is designed. Although the analysis capability of brake cooling performance has become quite reliable, due to lack of technology to predict contamination patterns, the design of the splash protection shield has relied on engineering judgment and/or vehicle tests. Optimization opportunities were restricted by cost and time associated with vehicle tests.

Indoor or laboratory testing of tire tread wear offers many advantages over vehicle fleet testing. Advances in test equipment capabilities and the technologies for defining and simulating meaningful tire loading histories has made indoor tread wear testing a reality. Tire loading histories are influenced by vehicle characteristics, wear course and driving style, and tire stiffnesses. Methods for independently characterizing each of these are reviewed. A simulation technique, TS-Sim, is also described that combines specific vehicle, course and tire characterizations to create a tire load history. The vehicle characterization is critical to the process since both wear rate and various forms of uneven and irregular wear are strongly dependent on vehicle suspension/steering characteristics and on dynamic load transfer behavior. The characterization process involves mapping the vehicle over a practical range of acceleration, deceleration and cornering maneuvers.

USING a high-speed motion picture camera, flame photographs were taken of the combustion process associated with the starting of hot gasoline engines. Compression ignition at isolated points followed by normal combustion caused peak cylinder pressures to occur prior to top dead-center under some low-speed engine conditions. In addition, an abnormal combustion phenomenon was observed in the last part of the charge to burn. The reaction rate was appreciably faster than normal for the engine speed and much slower than is usually observed in knocking combustion at normal engine speeds.