Search Results

There is a growing consensus that there will not be a single alternative to fossil fuels, but rather different fuels, fuel feedstocks, engine types and operating strategies. For stationary diesel engines, straight vegetable oils are an interesting alternative to fossil diesel, because of their potential for lower life cycle greenhouse gas emissions. Using animal fats is also compelling, as it does not imply the cultivation of oil-bearing seeds and related emissions, not to mention the ‘food versus fuel’ debate. The aim of the present work is to correlate engine performance and durability with the properties (composition) of these alternative fuels, to provide a basis from which standards can be formulated for the properties of oils and fats to be used as engine fuel. Tests on different oils and fats are reported.

The use of a soy-based diesel fuel (biodiesel) has potential advantages over the use of a conventional petroleum diesel fuel including: Reduced dependence on foreign petroleum Lowering of greenhouse gas emissions Less air pollution and related public health risks in urban areas A life cycle study performed by the U.S. Department of Energy's National Renewable Energy Laboratory, the U.S. Department of Agriculture's Office of Energy and Ecobalance (completed in May 1998) helped to quantify the environmental benefits of the “cradle-to-grave” production and use of biodiesel. The study showed, for example, that substituting 100% biodiesel for petroleum diesel in urban buses reduced the life cycle emissions of carbon dioxide (CO2) by 78%. The study also pointed out some trade-offs of using biodiesel including increased life cycle hydrocarbon and NOx emissions.

The bending fatigue performance of high temperature (1050 °C) vacuum carburized Nb modified 8620 steel, with niobium additions of 0.02, 0.06 and 0.1 wt pct, was evaluated utilizing a modified Brugger specimen geometry. Samples were heated at two different rates (20 and 114 °C min-1) to the carburizing temperature resulting in different prior austenite grain structures that depended on the specific Nb addition and heating rate employed. At the lower heating rate, uniform fine grained prior austenite grain structures developed in the 0.06 and 0.1 Nb steels while a duplex grain structure with the presence of large (>200 μm grains) developed in the 0.02 Nb steel. At the higher heating rate the propensity for abnormal grain growth was highest in the 0.02 Nb steel and complete suppression of abnormal grain growth was achieved only with the 0.1 Nb steel.

In stamping advanced high strength steels (AHSS), the deviations from desired part geometry caused by springback from a radius, curl, twist, and bow are major impediments to successfully producing AHSS parts. In general, the conventional elastic modulus is used to quantify the strain that occurs on unloading. This unloading strain causes deviations from desired part geometry. Considerable evidence in the literature indicates that for tensile testing, the conventional elastic modulus does not accurately describe the unloading strain. The present study uses new data and results from the literature to examine the average slope of tensile stress strain curves on unloading. This slope is termed the effective unloading modulus. The results from this study quantitatively describe how the effective unloading modulus decreases with increasing strength, prestrain, and unloading time.

High strain rate sheet tensile tests (up to 300s-1) and Ohio State University (OSU) formability tests (up to an estimated strain rate of 10s-1) were performed to examine the effect of strain rate on the mechanical properties and formability of five ferritic stainless steels: HIGH PERFORMANCE-10™ 409 (HP-10 409), ULTRA FORM® 409 (UF 409), HIGH PERFORMANCE-10™ 439 (HP-10 439), two thicknesses of 18 Cr-Cb™ stainless steel, all supplied by AK Steel, and Duracorr®, a ferrite-tempered martensite dual-phase stainless steel supplied by Bethlehem Steel Corporation. Tensile results show that increasing strain rate resulted in increases in yield stress, flow stress, and stress at instability for all alloys tested. In addition, increases in uniform and total elongation were also found for each of the five alloys.

Forging simulations with a 1522 steel microalloyed by additions of 0.25% Mo, 0.13% V and 0.01% Ti were performed on a laboratory thermomechanical processing simulator. The forging conditions included a strain rate of 22s-1, 50% strain, and temperatures in the range from 1200°C to 950°C. The true stress was found to increase with decreasing deformation temperature for all values of instantaneous true strain. The maximum flow stress increased two-fold as deformation temperature decreased from 1200°C to 950°C, and the recrystallized austenite grain size decreased by a factor of two for this same decrease in temperature. Microstructures evolve from bainitic/ferritic at a cooling rate of 1.4°C/s, to fully martensitic at 16.8°C/s, independent of deformation temperature. Room temperature hardnesses depended primarily on cooling rate and were essentially independent of deformation temperature.

Regulated emissions (THC, CO, NOx, and PM) and particulate SOF and sulfate fractions were determined for a 1995 Detroit Diesel Series 50 urban bus engine at varying fuel sulfur levels, with and without catalytic converters. When tested on EPA certification fuel without an oxidation catalyst this engine does not appear to meet the 1994 emissions standards for heavy duty trucks, when operating at high altitude. An ultra-low (5 ppm) sulfur diesel base stock with 23% aromatics and 42.4 cetane number was used to examine the effect of fuel sulfur. Sulfur was adjusted above the 5 ppm level to 50, 100, 200, 315 and 500 ppm using tert-butyl disulfide. Current EPA regulations limit the sulfur content to 500 ppm for on highway fuel. A low Pt diesel oxidation catalyst (DOC) was tested with all fuels and a high Pt diesel oxidation catalyst was tested with the 5 and 50 ppm sulfur fuels.

With the increased use of tubular steel products, especially for automotive hydroforming applications, there is increased interest in understanding the mechanical properties measured by tensile tests from specimens of different orientations in the tube. In this study, two orientations of tensile specimens were evaluated -- axial specimens with and without flattening and flattened circumferential specimens. Three steels were evaluated -- two thicknesses of aluminum killed drawing quality (AKDQ) steel and one thickness of high strength low alloy (HSLA) steel. Mechanical property data were obtained from the flat stock, conventional production tubes and quasi tubes. Quasi tubes were produced from the flat stock on a 3-roll bender, but the quasi tube was not welded or sized.

The internal combustion engine with compression ignition is still the most important power plant for heavy duty transport, railway transport, marine applications and generator sets. Fuel cost and emission regulations drive manufacturers to switch to alternative fuels. The understanding and prediction of these fuels in the spray and combustion process will be very important for these issues. In the past, lot of research was done for conventional diesel fuel by optically analyzing both spray and combustion. However comparison between different groups is difficult since qualitative results and accuracies are depending in the used definitions and methods. The goal of present research is to verify the behavior pure oils compared to more standard fuels while paying lot of attention to the interpretation of the measurement results.

Knowledge of the net thinning strain that occurs in a sheet as it is bent over a single radius is an important component in understanding sheet metal formability. The present study extends the initial work of Swift on thinning during plane-strain bending to sheet steels with power law stress-strain behavior and with the inclusion of friction. The experimental data come from studies on the enhanced forming limit curve on DQSK steel and analysis of the curl behavior of 590R and DP600 steels. Results for single radius bending from these studies are used in the present investigation. It has been found that the amount of net thinning strain depends on back tension, initial plane-strain yield strength, and the maximum true bending strain calculated for the neutral plane at the mid-thickness of the sheet.

The influences of laboratory-induced hydrogen on the tensile deformation and fracture behavior of selected sheet steels including conventional DQSK and HSLA steels as well as newer DP and TRIP grades were evaluated. The effects of cold work, simulated paint baking, and natural aging were considered. Hydrogen effects were observable by increased flow stress, decreased ductility, altered neck geometry, and altered fracture mechanisms. Differences among the steels and conditions were observed and interpreted on the basis of microstructure, fracture behavior, and theories of hydrogen embrittlement.

Non-Road Mobile Machinery (NRMM) incorporates a wide variety of machines not intended for the transport of passengers or goods on the road. This includes small gardening equipment, construction, mining, agricultural, and forestry machinery up to locomotives and inland waterway vessels, mostly using an internal combustion engine. NRMM was often overlooked and neglected in the past when considering pollutant and greenhouse gas emissions. Due to their high diversity, they are hard to categorize, resulting in a lack of available data. As emissions from road transport are being tackled by regulations, the emissions of NRMM become an increasing part of total transport emissions. An alternative to fossil fuels will be required for the energy supply of NRMM to fully commit to the CO2 reduction goals, and to fulfil the future requirements of legislators and public opinion.

In 2004 the European Parliament ratified the Euro III and IV standards limiting the pollutant emission of, among others, rail and marine diesel engines. In these sectors, it is particularly important to keep any fuel consumption penalty, when reducing emissions, to a strict minimum. Furthermore, exhaust gas after treatment is mostly avoided for cost reasons. Thus, manufacturers are looking to pretreatment of fuels, alternative fuels, and limiting engine-out emissions as ways to attain the required emission levels. This paper discusses the experimental work done on a 1324 kW, 1000 rpm six cylinder marine diesel engine equipped with mechanical unit injectors. The aim was to determine the influence of compression ratio and fuel injection parameters on engine-out emissions, with emphasis on NOx emissions. A range of fuel injection parameters were examined, varying the start of injection, pump plunger diameter, injection pressure, and injector nozzle geometry.

Methane emissions from lean-burn natural gas engines can be relatively high. As natural gas fueled vehicles become more prevalent, future regulations may restrict these emissions. Preliminary reports indicated that conventional, precious metal oxidation catalysts rapidly deactivate (in less than 50 hours) in lean-burn natural gas engine exhaust. This investigation is directed at quantifying this catalyst deactivation and understanding its cause. The results may also be relevant to oxidation of lean-burn propane and gasoline engine exhaust. A platinum/palladium on alumina catalyst and a palladium on alumina catalyst were aged in the exhaust of a lean-burn natural gas engine (Cummins B5.9G). The engine was fueled with compressed natural gas. Catalyst aging was accomplished through a series of steady state cycles and heavy-duty transient tests (CFR 40 Part 86 Subpart N) lasting 10 hours. Hydrocarbons in the exhaust were speciated by gas chromatography.

Drawbeads in production stamping dies often have insufficient penetration of the male bead into the female cavity. With insufficient penetration, the actual bending radii of the sheet metal are larger than the geometrical radii of the drawbead. The actual bending radii in the sheet directly affect the force that restrains sheet movement. To predict the restraining stress due to a drawbead, it is necessary to know the actual bending radii in the sheet as it passes though the drawbead. Data from a previous study are used to develop empirical regression equations for predicting measured radii of the sheet that is bent around the radii in a drawbead. A physical model for the evolution of the sheet radii as the drawbead closes is proposed. This model is consistent with the empirical equations and the mechanics of the sheet bending process.

Using liquid alcohols, such as methanol and ethanol, in spark-ignition engines is a promising approach to decarbonize transport and secure domestic energy supply. Methanol and ethanol are compatible with the existing fuelling and distribution infrastructure and are easily stored in a vehicle. They can be used in internal combustion engines with only minor adjustments and have the potential to increase the efficiency and decrease noxious emissions compared to gasoline engines. In addition, methanol can be synthesized from a wide variety of sources, including renewably produced hydrogen in combination with atmospheric CO₂. Presently, during the production of ethanol or methanol a dehydration step is always applied. This step accounts for a significant part of the entire production process' energy consumption and thus, from an economical point of view, methanol and ethanol could become more interesting alternative fuels if the costs related with dehydration could be reduced.

The effectiveness of three different techniques, designed to improve the bending fatigue life in comparison to conventionally processed gas-carburized 8620 steel, were evaluated with modified Brugger bending fatigue specimens and actual ring and pinion gears. The bending fatigue samples were machined from forged gear blanks from the same lot of material used for the pinion gear tests, and all processing of laboratory samples and gears was done together. Fatigue data were obtained on standard as-carburized parts and after three special processing histories: shot-peening to increase surface residual stresses; double heat treating to refined austenite grain size; and vacuum carburizing to minimize intergranular oxidation. Standard room-temperature S-N curves and endurance limits were obtained with the laboratory samples. The pinions were run as part of a complete gear set on a laboratory dynamometer and data were obtained at two imposed torque levels.

The work-hardening of three common automotive low carbon steel sheets is described in terms of two different types of microstructure based models. The first model employed is the classical Kocks-Mecking model. On the other hand, the second model incorporates the effect of the density evolution of non-redundant dislocations, also known as Geometrically Necessary Dislocations (GND), into the Kocks-Mecking hardening law. Each of both models was coupled to a Taylor-type crystal plasticity framework in order to follow the dislocation density evolution over all slip systems. One of the microstructural parameters employed on the calibration of the second model is the density of GND, parameter which was experimentally acquired from crystal orientation maps by EBSD (Electron Backscatter Diffraction) on the tensile samples.

The use of renewable fuels such as hydrogen and methanol in marine engines is a promising way to reduce greenhouse gas emissions from maritime transport. Hydrogen and methanol can be used as the main fuel in dual-fuel engines. However, the co-combustion of hydrogen-diesel and methanol-diesel needs to be carefully studied. In the present work, the ignition delay (ID) and laminar burning velocity (LBV) for pilot-ignited dual fuel engine operation with hydrogen or methanol are studied. A constant volume batch reactor numerical setup is used in the open source Cantera code to calculate the effect of the premixed fuel on the ID of the pilot fuel. Also, Cantera is used to simulate a freely-propagating, adiabatic, 1-D flame to estimate the laminar flame speed of either hydrogen or methanol and how it is affected by the presence of pilot fuel. First, suitable chemical kinetic schemes are selected based on experimental data collected from the literature.

Methanol is a promising fuel for future spark-ignition engines. Its properties enable increased engine efficiency. Moreover, the ease with which methanol can be reformed, using waste exhaust heat, potentially offers a pathway to even higher efficiencies. The primary objective of this study was to build and validate a model for a methanol fueled direct-injection spark-ignition engine with on-board fuel reforming for future investigation and optimization. The second objective was to understand the combustion characteristics, energy losses and engine efficiency. The base engine model was developed and calibrated before adding a reformed-exhaust gas recirculation system (R-EGR). A newly developed laminar burning velocity correlation with universal dilution term was implemented into the model to predict the laminar burning velocity with the presence of hydrogen in the reforming products.