Search Results

Recent developments in the prediction of the contribution of wind noise to the interior SPL have opened a realm of new possibilities in terms of i) how the convective and acoustic sources terms can be identified, ii) how the interaction between the source terms and the side glass can be described and finally iii) how the transfer path from the sources to the interior of the vehicle can be modelled. This paper discusses in detail these three aspects of wind noise simulation and recommends appropriate methods to deliver required results at the right time based on i) simulation and experimental data availability, ii) design stage and iii) time available to deliver these results. Several simulation methods are used to represent the physical phenomena involved such as CFD, FEM, BEM, FE/SEA Coupled and SEA.

A vehicle's underbody has various wind noise sources due to the complex flow structure. Acoustic holography using NAH (Near-field Acoustic Holography) is adopted to identify the sources, and to analyze the characteristics of them such as positions, strengths, and contributions to interior sound. Reduction procedure of wind noise from a vehicle's underbody will be investigated.

This paper describes an automated path following system using vision sensor. Lateral control law for path following is especially underlined which is developed by using the backstepping control design methodology. To establish the proposed control system, the lateral offset to the reference path, the heading angle of vehicle relative to tangent line to the path, and path curvature are required. Those inputs to the controller have been calculated through Kalman filter which is frequently adopted for the purpose. The lane mark detection has been achieved in an ECU (Electric Control Unit) platform with vision sensor. The yaw rate and side-slip angle also needed in the controller are estimated by Kalman estimator. To show the performance of the proposed controller under different speeds, experiment has been conducted on a proving ground having straight and curve sections with the curvature of about 260m.

This paper describes an approach to simulate spindle coupled full vehicle durability tests for the purpose of completing virtual durability evaluations on components and full vehicles before a prototype is available. The reproduction of measured spindle loads was achieved on a virtual model of a passenger car coupled to a 4 Degree of Freedom (DOF) and 6 DOF spindle coupled test system. The tools and process improvements developed here will aid both test and analysis engineers in working closer together in solving their durability problems. By using Remote Parameter Control® (RPC®) technology in the virtual world, analysts have a new method to understand the virtual model by reproducing field-measured or generic road predicted signals for a variety of road surfaces. With newly created test rig models and a user friendly RPC™ iteration process, virtual testing that accurately replicates laboratory tests are now a reality.

CAE capabilities have long been used for performing static and dynamic structural analysis during the seat design process. More recently, the soft parts of the seat including foams, trim and suspension have also been modeled with CAE. The purpose of this modeling is to better understand the physical phenomena which are involved in the sitting process, to enhance seat design knowledge, and to replace as much physical testing during the design process with virtual, CAE testing. This paper presents the first part of a multi-phased, both experimental and numerical project. The aim of this first stage is to assess the capabilities of a CAE methodology to predict FMVSS 202a backset. Based on CAD data, a finite element mesh of the seat was built. The mechanical behavior of all parts was characterized through experiments on material samples.

This paper presents the second part of a multi-phased, both experimental and numerical project, devoted to the use of Virtual Prototyping techniques for seat design. The aim of this stage is to assess the capabilities of a CAE methodology to predict some comfort-related mechanical parameters, such as overall hardness and plushness, as a base engineering approach to quantify an occupant perception of both long- and short-term comfort. For hardness, a simple human surrogate (SAE AM50 Buttock Form) is applied on the bottom cushion of a fully trimmed, current production FORD seat, following a load cycle. For initial softness, a round probe is indented at different locations of both backrest and bottom cushions, following loading cycles. The resulting load-deflection curves predicted by numerical simulation are in good agreement with the experimental ones.

To develop future electrical and autonomous cars, it is important to virtually test the car in real driving circumstances, including on wet road or under heavy rain conditions. It is especially critical to check that no water prevents the sensors of the driving assistance systems or autonomous cars from working properly, that water intrusion does not disturb electrical equipment, and that the driver’s visibility remains good under rain condition. ESI Group has introduced the Finite Point Method (FPM) in Virtual Performance Solution (VPS) as a CFD mesh free module in order to simulate the interaction of water with the car structure. It was initially specialized for tank sloshing and water drain applications for car closures and is now extended to other application fields. The objective is to enable a holistic prediction of the car behavior under realistic driving conditions, using a virtual car prototype.

This paper presents an integrated simulation process which has been performed in order to assess the riding comfort performance of a vehicle seat system virtually. Present methods of seat comfort design rely on the extensive testing of numerous hardware prototypes. In order to overcome the limitations of this expensive and time-consuming process, and to fasten innovation, simulation-based design has to be used to predict the seat comfort performance very early in the seat design process, leading to a drastic reduction in the number of physical prototypes. The accurate prediction of the seat transfer function by numerical simulation requires a complete simulation chain, which takes into account the successive stages determining the final seat behaviour when submitted to vibrations. First the manufacturing stresses inside the cushion, resulting from the trimming process, are computed.

In this paper, the vibration and noise reduction technology for diesel common rail injection system is studied. The NV problems of the injection system come typically from mechanical contacts (injector needle, pump) or fluid pulsations. They are exciting the injection system, which translates the excitations to the engine through the connection points. But it's not easy to identify the characteristic of internal excitation force exactly, so the simulation model based measurement test is considered at here. In order to predict the vibrations due to excitation related with the injection system of the diesel engine, the 1D/3D simulation models are used and the necessary dynamic tests, which are needed to create and validate the models, are done in the test bench.

A fractional recirculation of cabin air was proposed and studied to improve cabin air quality by reducing cabin particle concentrations. Vehicle tests were run with differing number of passengers (1, 2, 3, and 4), four fan speed settings and at 20, 40, and 70 mph. A manual control was installed for the recirculation flap door so different ratios of fresh air to recirculated air could be used. Full recirculation is the most efficient setting in terms of thermal management and particle concentration reduction, but this causes elevated CO₂ levels in the cabin. The study demonstrated cabin CO₂ concentrations could be controlled below a target level of 2000 ppm at various driving conditions and fan speeds with more than 85% of recirculation. The proposed fractional air recirculation method is a simple yet innovative way of improving cabin air quality. Some energy saving is also expected, especially with the air conditioning system.

Quality and refinement are of paramount importance for luxury vehicles. The rapid electrification of the automotive industry has increased the contribution of aeroacoustics to the consumer perception of sound quality. The ability to predict whole vehicle aeroacoustic interior noise is essential in the development of vehicles with an extraordinary acoustic environment. This publication summarises the development of a process to combine lattice Boltzmann computational fluid dynamics simulations, with a whole vehicle statistical energy analysis model, to predict the aeroacoustic contribution from all relevant sources and paths. The ability to quantify the relative contribution of glazing panels and path modifications was also investigated. The whole vehicle aeroacoustic interior noise predictions developed, were found to be within 2dB(A) of comparable test vehicle wind tunnel measurements, across a broad frequency range (250-5000 Hz).

This paper summarizes the validation of prototype vehicle-to-infrastructure (V2I) safety applications based on Dedicated Short Range Communications (DSRC) in the United States under a cooperative agreement between the Crash Avoidance Metrics Partners LLC (CAMP) and the Federal Highway Administration (FHWA). After consideration of a number of V2I safety applications, Red Light Violation Warning (RLVW), Curve Speed Warning (CSW) and Reduced Speed Zone Warning with Lane Closure Warning (RSZW/LC) were developed, validated and demonstrated using seven different vehicles (six passenger vehicles and one Class 8 truck) leveraging DSRC-based messages from a Road Side Unit (RSU). The developed V2I safety applications were validated for more than 20 distinct scenarios and over 100 test runs using both light- and heavy-duty vehicles over a period of seven months. Subsequently, additional on-road testing of CSW on public roads and RSZW/LC in live work zones were conducted in Southeast Michigan.

The comfort assessment of seats in the automotive industry has historically been accomplished by subjective ratings. This approach is expensive and time consuming since it involves multiple prototype seats and numerous people in supporting processes. In order to create a more efficient and robust method, objective metrics must be developed and utilized to establish measurable boundaries for seat performance. Objective measurements already widely accepted, such as IFD (Indentation Force Deflection) or CFD (Compression Force Deflection) [1], have significant shortcomings in defining seat comfort. The most obvious deficiency of these component level tests is that they only deal with a seats' foam rather than the system response. Consequently, these tests fail to take into account significant factors that affect seat comfort such as trim, suspension, attachments and other components.

Traditional automotive seat development has relied on a series of physical prototypes that are evaluated and refined in an iterative fashion. Costs are managed by sharing prototypes across multiple attributes. To further manage costs, many OEMs and Tier 1s have, over the past decade, started to investigate various levels of virtual prototyping. The change, which represents a dramatic paradigm shift, has been slow to materialize since virtual prototyping has not significantly reduced the required number of physical prototypes. This is related to the fact virtual seat prototyping efforts have been focused on only selected seat attributes - safety / occupant positioning and mechanical comfort are two examples. This requires that physical prototypes still be built for seat attributes like craftsmanship, durability, and thermal comfort.

Statistical Energy Analysis (SEA) is widely used for modeling the vibro-acoustic response of large and complex structures. SEA makes simulations practical thanks to its intrinsic statistical approach and the lower computational cost compared to FE-based techniques. However, SEA still requires underlying models for subsystems and junctions to compute the SEA coefficients which appear in the power balance equations of the coupled system. Classically, such models are based on simplified descriptions of the structures to allow analytical or semi-analytical developments. To overcome this limitation, the authors have proposed a general approach to SEA which only requires the knowledge of impedances of the structures to compute SEA coefficients. Such impedances can always be computed from an accurate FE model of each component of a coupled system.

In order to align with net-zero CO2 ambitions, automotive OEMs have been developing increasingly sophisticated strategies to minimise the impact that combustion engines have on the environment. Intelligent thermal management systems to actively control coolant flow around the engine have a positive impact on friction generated in the power cylinder by improving the warmup rate of cylinder liners and heads. This increase in temperature results in an improved frictional performance and cycle averaged fuel consumption, but also increases the piston to liner clearances due to rapid warm up of the upper part of the cylinder head. These increased clearances can introduce piston slap noise and substantially degrade the NVH quality to unacceptable levels, particularly during warmup after soak at low ambient temperatures. Using analytical techniques, it is possible to model the thermo-structural and NVH response of the power cylinder with different warm up strategies.

The Hybrid FE-SEA method has been used to create a fast/efficient model to predict structure-borne noise propagation in a fully trimmed vehicle over the frequency range from 200 to 1000 Hz. The method was highlighted along with the modeling process and extensive validation results in previously published papers [1-3]. The use of the model to analyze structure-borne noise in the full vehicle, and to design and evaluate the impact of counter measures was described. In this study, the Hybrid FE-SEA method is used identify potential design changes to improve the acoustic performance. First, results from a noise path analysis are used to identify key contributors to interior noise. Next, potential design strategies for reducing the interior noise are introduced along with implications on the model. Finally, sample prediction results illustrating the impact of design changes on interior noise levels are shown along with experimental validation results.

As the global automotive industry continues to strive for improved performance at lower costs, the use of blow-molded thermoplastics in underhood components offers a wide range of benefits, including: 1. Cost reduction 2. Weight reduction 3. Improved recyclability 4. Multi-functional part design opportunities 5. Reduction in number of parts and materials in the engine compartment 6. Greater temperature resistance to handle increasing powertrain temperatures 7. Easier assembly/disassembly for productivity improvements and cost savings in the manufacturing process 8. Reduced noise 9. Improved engine performance (up to 2 percent) Underhood applications where blow-molded technology can provide these advantages include turbo- charge ducts, air ducts, crankcase venting hoses, resonators, coolant reservoirs, and pipes and hoses for oil cooling, air conditioning and coolant systems. This technology is now used in the European automotive market and in Japan.

This study presents the NVH characteristics of a passenger vehicle with a three-cylinder engine and a Continuously Variable Transmission (CVT) and an optimization procedure to achieve balance between fuel economy and NVH. The goal of this study is to improve fuel economy by extending the lock-up area of the damper clutch at low vehicle speed and to minimize booming noise and body vibration caused by the direct connection of the engine and transmission. Resonance characteristics of the chassis systems and driveline have been studied and optimized by the experiment. NVH behavior of the vehicle body structure is investigated and modifications for refinement of booming and body vibration are proposed by simulation using MSC NASTRAN. Calibration parameters for CVT control are optimized for fuel economy and NVH. As a result, the lock-up clutch area has been extended by 300RPM and the fuel economy has been improved by about 1%, while the NVH characteristics of the vehicle satisfy the targets.

The alternator provides power to vehicle electrical loads with the battery, and its maximum current depends on various factors such as electrical load, engine speed, thermal condition, and other variables. Above all, thermal effects make alternator simulations more complicated. For example statically similar conditions may show different results according to the temperature variation for each alternator operation. This paper proposes a two-stage statistically-based model structure which separates dynamic thermal effects from steady state performance. The method was validated by experiments and shows good predictive performance, suitable for use in test reduction.