Search Results

A cooperation of several research partners supported by the German Federal Ministry of Research and Education proposes a new active matrix LED light source. A multi pixel flip chip LED array is directly mounted to an active driver IC. A total of 1024 pixel can be individually addressed through a serial data bus. Several of these units are integrated in a prototype headlamp to enable advanced light distribution patterns in an evaluation vehicle.

This paper will outline the results of a study performed to analyze the market introduction of x-by-wire applications in the context of weak global industry environment, technological and legislative challenges, standardization issues and end customer benefits. This paper attempts to provide a bird-view on influence factors and impacts for the x-by-wire market, including e.g. the end customer's acceptance and legal environment driving further development in specific areas. Further, major driving forces on semiconductor/component level will be outlined regarding e.g. pin-count, computation performance and heat dissipation, but also possible scenarios and solutions towards safe and efficient system design and partitioning.

Automotive powertrain and safety systems under design today are highly complex, incorporating more than one CPU core, running with more than 100 MHz and consisting of several 10 million transistors. Software complexity increases similarly making new methodologies and tools mandatory to manage the overall system. The use of accurate virtual prototypes improves the quality of systems with respect to system architecture design and software development. This approach is demonstrated with the example of the PCP/GPTA subsystem for Infineon's AUDO-NG powertrain controllers.

More than ever, microcontroller performance in cars has a direct impact on the driving experience, on compliance with improved safety, ever-stricter emissions regulations, and on fuel economy. The simple microcontrollers formerly used in automobiles are now being replaced by powerful number-crunchers whose performance can no longer be measured in MIPS. Instead, their effectiveness is based on a coherent partitioning between analog and digital, hardware and software, tools and methodology. To make an informed choice among the available devices, what the designer needs are benchmarks that are specific to automotive applications, and which provide a realistic representation of how the device will perform in the automotive environment. This presentation will explore the role of new benchmarks in the development of complex automotive applications.

More than ever, microcontroller performance in cars has a direct impact on the driving experience, on compliance with improved safety, ever-stricter emissions regulations, and on fuel economy. The simple microcontrollers formerly used in automobiles are now being replaced by powerful number-crunchers with incredible levels of peripheral integration. As a result, performance can no longer be measured in MIPS (Millions of Instructions Per Second). A microcontroller's effectiveness is based on coherent partitioning between analog and digital, hardware and software, tools and methodology. To make an informed choice among the available devices, the designer needs benchmarks that are specific to automotive applications, and which provide a realistic representation of how the device will perform in the automotive environment.

This paper outlines the results of a study performed to analyze the mission of TTCAN from applications to products for automotive systems. As commonly acknowledged communication is one of the key elements for future and even present systems such as an automobile. A dramatically increasing number of busses and gateways even in low- to midrange vehicles is putting significant burden upon the validation scenario as well as the cost. Accordingly, numerous new initiatives have been started worldwide in order to find solutions to this; some of them by the definition of enhanced or new protocols. This paper shall have a look particular on the new standard of TTCAN (time-triggered communication on CAN). This protocol is based on the CAN data link layer as specified in ISO 11898-1 and may use standardized CAN physical layers such as specified in ISO 11898-2 (high-speed transceiver) or in ISO 11898-3 (fault-tolerant low-speed transceiver).

Trans Tech recently debuted the all-electric eTrans school bus providing a total zero emission school bus. The presentation will demonstrate Smith Electric Vehicles and their history with electric vehicles. The presentation will help ensure that everybody has an idea of what the electric school bus will do and to dispel any rumors about the vehicle. Presenter Brian S. Barrington, Trans Tech. Bus

In addition to basic switching functionality, smart power switches mainly provide diagnostic and protection functions, e.g. for short circuits to the load, which makes it all the more surprising that short circuit protected smart switches have been used for years in automotive applications without there being a precise definition of a short circuit. This article describes what Infineon has done to fill this gap. It was first necessary to define the kind of short circuits likely to occur in automotive applications and to specify the use and operating points of the smart switches. The next logical step was the standardization of the test circuit and application conditions in the AEC (Automotive Electronics Council) to allow an industry-wide comparison of the test results.

Increasing fuel costs and emission regulations force the car manufacturers to develop powerful but efficient engines. The 3-liter car (3-liter/100 km fuel consumption → 80 miles/gallon) is one of the slogans. To fulfill these requirements a fully electronic controlled Engine Management is necessary. Carburetor systems are replaced by fuel injection systems. Direct injection for Diesel as well as for gasoline engines is the clear trend for the future. The mechanical throttle systems, used for a long time will not fit to the requirements of direct injection. A DC motor for electronic throttle control in conjunction with λ regulation and exhaust gas recirculation are the key elements for low emission cars. Also the automotive ignition system is in a process of change today.

For highly automated driving, commercial vehicles require an Electric/Electronic (E/E) architecture, which - in addition to sensor fusion - ensures safety-critical processes such as steering and braking at all times. Among other things, a redundant 24 V supply with corresponding disconnection is required. The battery switch is a key component. Commercial, construction, and agricultural vehicles (CAV) need to operate at the highest possible availability and the lowest possible cost of ownership. This is why automated and autonomous driving has the potential to revolutionize the CAV sector. Driverless machines can be operated around the clock and almost non-stop. Platooning allows automated, interconnected trucks to drive in a convoy and very close to each other. Platooning saves fuel.

Single Edge Nibble Transmission (SENT) is a promising low-cost solution for communication between off-ECU sensors and a microcontroller. First, this paper analyses the advantages of digital sensors with a special focus on position sensors. The possible integration of SENT in other application fields (such as pressure sensors) is also discussed. Secondly, it describes possible solutions for handling SENT communication on microcontrollers and it gives practical examples based on Infineon's TriCore and XC2000 families. It discusses the constraints and limitations on software level and how they could be solved by dedicated hardware implementations. Finally, this paper presents the Short PWM Code (SPC) protocol, which is a further extension of the SENT protocol. SPC aims at increasing the performance of the communication link and reducing system costs at the same time. By allowing bidirectional communication, SPC opens the way to new system relevant functionalities.

The signal delivery and quality of sensor data is of growing importance for modern automotive control applications. Sensors tend to be calibrated subsystems that are designed to stay in a defined tolerance and thus can easily be modeled. Compared to this deterministic behavior the transmission channel is time variant due to EMC and aging of contacts for example. The use of analog signaling, which is the actual state of realization in many cases, is sensitive to the time variant effects mentioned before. This time variance is hard to consider for the control system development. In this paper we will analyze the role of the sensor in the signal supply chain and discuss approaches for digital sensor-ECU communication and their potential to establish a link, which allows neglecting low level effects of the channel.

Fuel efficiency and clean combustion engine versus high engine performance - which will increase up to factor 10 in the next 5 years - with less engine displacement are driving more complex engine control systems in today's and future vehicles. The challenge is not only to design a perfect engine, but also to incorporate the right semiconductors. Beside this demand on high sophisticated electronics the demand on cost reduction - especially for small cars - is one driving factor for a smart partitioning. Infineon offers sensors, microcontrollers and power semiconductors for today's engine management platforms and therefore owns the right technologies to manufacture those devices. This opens up the possibility to integrate more functionality in less devices as in today's partitioning or to define electronics to simplify complex control strategies and to optimize the performance of each device.

The number of safety critical automotive applications employing high current brushless motors continues to increase (Steering, Braking, and Transmission etc.). There are many benefits when moving from traditional solutions to electrically actuated solutions. Some of these benefits can include increased fuel economy, simplified vehicle installation and packaging, increased feature set, improved safety and/or convenience, simplified unit assembly and modular testability prior as well as during vehicle manufacturing. The trend to implement brushless motors in these applications (which require electronically controlled commutation) has also brought with it the need for powerful inverters, which primarily consist of Power MOSFETs and MOSFET Driver ICs. This paper reviews the challenges associated with the design of safety critical electronic systems which combine sensing, control and actuation.

ISO 26262 is the actual standard for Functional Safety of automotive E/E (Electric/Electronic) systems. One of the challenges in the application of the standard is the distribution of safety related activities among the participants in the supply chain. In this paper, the concept of a Safety Element out of Context (SEooC) development will be analyzed showing its current problematic aspects and difficulties in implementing such an approach in a concrete typical automotive development flow with different participants (e.g. from OEM, tier 1 to semiconductor supplier) in the supply chain. The discussed aspects focus on the functional safety requirements of generic hardware and software development across the supply chain where the final integration of the developed element is not known at design time and therefore an assumption based mechanism shall be used.

Functional safe systems fulfilling the ISO 26262 standard are getting more important for automotive applications where additional redundant and diverse functionality is needed for higher rated ASIL levels. This can result in a very complex and expensive system setup. Here we present a sensor product developed according ISO 26262. This sensor product comprises a two channel redundant and also diverse implemented magnetic field sensor concept with linear digital outputs on one monolithically integrated silicon substrate. This sensor is used for ASIL D applications like power-steering torque measurement, where the torque is transferred into a magnetic field signal in a certain magnetic setup, but can also be used in other demanding sensor applications concerning safety. This proposed and also implemented solution is beneficial because of implementation on a single chip in one single chip-package but anyway fulfilling ASIL D requirements on system level.

Position detection and control is necessary in modern automotive applications because of remotely controlled actuators, such as window lifters or windshield. In recent years, the demand for reliable actuators for safety critical systems, such as power steering systems, has also increased significantly. This creates a growing demand for fast, accurate and efficient servo motor systems that are increasingly smarter, smaller and cheaper. One interesting option is to use Giant Magneto Resistive (GMR) angle sensors to replace the resolvers, Hall, inductive and Anisotropic Magneto Resistive Effect (AMR) Sensors commonly used today for shaft-angle measurements. In principle, there are functional differences among various angle measurement technologies; thus, the effect of switching between them needs to be analyzed.

This paper will give an overview of multicore in automotive applications, covering the trends, benefits, challenges, and implementation scenarios. The automotive silicon industry has been building multicore and multiprocessor systems for a long time. The reasons for this choice have been: increased performance, safety redundancy, increased I/O & peripheral, access to multiple architectures (performance type e.g. DSP) and technologies. In the past, multiprocessors have been mainly considered as multi-die, multi-package with simple interconnection such as serial or parallel busses with possible shared memories. The new challenge is to implement a multicore, micro-processor that combines two or more independent processors into a single package, often a single integrated circuit (IC). The multicores allow a computing device to exhibit some form of thread-level parallelism (TLP).

In modern vehicles, the number of small electrical drive systems is still increasing continuously for blowers, fans and pumps as well as for window lifts, sunroofs and doors. Requirements and operating conditions for such systems varies, hence there are many different solutions available for controlling such motors. In most applications, simple, low-cost DC motors are used. For higher requirements regarding operating time and in stop-start capable systems, the focus turns to highly efficient and durable brushless DC motors with electronic commutation. This paper compares various electronic control concepts from a semiconductor vendor point of view. These concepts include discrete control using relays or MOSFETs. Furthermore integrated motor drivers are discussed, including system-on-chip solutions for specific applications, e.g. specific ICs for window lift motors with LIN interface.

For the past approximately 20 years, the Serial Peripheral Interface (SPI) has been the established standard for serial communication between a host or central microprocessor and peripheral devices. This standard has been used extensively in control modules covering the entire spectrum of automotive applications, as well as non-automotive applications. As the complexity of engine control modules grows, with the number of vehicle actuators being controlled and monitored increasing, the number of loads the central microprocessor has to manage is growing accordingly. These loads are typically controlled using discrete and pulse-width modulated (PWM) outputs from the microcontroller when real-time operation is essential or via SPI when real-time response is not critical. The increase of already high pin-count on microcontrollers, the associated routing effort and demand for connected power stages is a concern of cost and reliability for future ECU designs.