Search Results

This study was initiated to evaluate the thermal characteristics of a vehicle underbody using math-based computational fluid dynamics (CFD) simulation based on 3-D configuration. Simulations without heat shields were carried out for different vehicle operating conditions which placed several areas at risk of exceeding their thermal design limits. Subsequently, simulations with several heat shield designs were performed. Results show that areas at risk without shields are well within thermal design limits when shielded. Part of the CFD simulation results were compared with experimental data, with reasonable correlation. The CFD approach can provide useful design information in a very short time frame.

This paper describes the design, synthesis-analysis and development of the unique vehicle structure architecture for the fifth generation Chevrolet Corvette, ‘C5’, which starts in the 1997 model year. The innovative structural layout of the ‘C5’ enables torsional rigidity in an open roof vehicle which exceeds that of all current production open roof vehicles by a wide margin. The first structural mode of the ‘C5’ in open roof configuration approaches typical values measured in similar size fixed roof vehicles. Extensive use of CAE and a systems methodology of benchmarking and requirements rolldown were employed to develop the ‘C5’ vehicle architecture. Simple computer models coupled with numerical optimization were used early in the design process to evaluate every design concept and alternative iteration for mass and structural efficiency.

THIS paper describes the springs, control system, and ride of the air suspension system on the 1958 Buick. The system is a semiclosed one, providing a variable-rate suspension, automatic leveling and trim control, and manual lift. The latter feature is a knob below the instrument panel which can be operated when necessary to cope with unusual clearance conditions. The car remains at the same height with loads of up to five passengers and 500 lb in the trunk. The authors describe the road-holding ability of a car with this suspension system as excellent.

This paper describes some methods for greatly reducing or possibly eliminating subjective tuning of suspension parts for ride and handling. Laptop computers can now be used in the vehicle to guide the tuning process. The same tools can be used to select solutions that reduce sensitivity to production and environmental variations. OBJECTIVE Reduce or eliminate time required for tuning of suspension parts for ride characteristics. Improve the robustness of ride performance relative to variations in ambient temperature and production tolerances. PROBLEM REQUIRING SOLUTION AND METHOD OF APPROACH Traditional development programs for new vehicles include time-consuming subjective ride evaluations. One example is shock absorber tuning. Even if sophisticated models define force-velocity curves, numerous hardware iterations are needed to find valvings that will reproduce the curves. Many evaluation rides are needed to modify the valvings to meet performance targets.

This paper presents a method for modeling large deformations of structures using scale plastic models. The method was used to predict the dynamic barrier crash performance of a proposed vehicle structure with the aid of a computer simulation of the collision. The use of the technique can provide design direction in the early stages of the vehicle design process.

Car manufacturers continue to strive to find creative routes to differentiate their vehicles while continuing to reduce cost. Acoustic comfort derived from high performance sprayable dampener systems is one important option for OEM's to differentiate their models. But there is a significant conflict between high performance, low cost and vehicle weight reduction. This paper describes an innovative vibration dampening material resin. It is a one part, reactive, solvent free, sprayable, epoxy based technology using a unique polymer resin with reduced safety labeling requirements. Good corrosion protection and oil absorption characteristics allow this resin to be applied in either the body or paint shop facilities. Benchmarking against the existing dampener type in the areas of damping performance, process costs, ease of application and environment/health aspects shows that this new generation of epoxy damper is superior to other current damper coatings.

A front suspension laboratory test procedure was developed to reproduce time-correlated fatigue damaging events from a light truck road durability test. Subsequently, the performance of front suspension systems for the GMT 400 light truck program were evaluated in terms of customer reliability. Both prototype and pilot testing, as well as computer modeling, were used in the evaluation.

Saturn currently injection molds and paints PPE+PA66 exterior body panels in its Spring Hill, TN facility. These manufacturing operations result in a continuous stream of waste material that needs to be responsibly and economically managed. This paper will summarize the process that General Motors and Saturn used to evaluate and validate the use of post-industrial painted PPE+PA66 reprocessed material in Saturn and General Motors' wheel trim applications (wheel covers). Not only did this project increase the amount of recycled content in General Motors' vehicles, but it also provided Saturn Corporation with a favored outlet for an internal waste stream.

Proper performance of a vehicle's suspension system is required to ensure safe, comfortable operation of a vehicle. A suspension-testing device that can determine the condition of the suspension system, specifically the dampers, has been designed. The tests described by this paper seek to evaluate the performance of the device by testing vehicles and comparing to other methods of measuring suspension system performance that are currently in use. The suspension-testing device has the ability to discover degraded performance of the suspension system through a 2-minute test with the vehicle in operating condition.

Aspirating airbag modules are unique from other designs in that the gas entering the airbag is a mixture of inflator-delivered gas and ambient-temperature air entrained from the atmosphere surrounding the module. Today's sophisticated computer simulations of an airbag deployment typically require as input the mass-flow rate, chemical composition and thermal history of the gas exiting the canister and entering the airbag. While the mass-flow rate and temperature of the inflator-delivered gas can be obtained from a standard tank test, information on air entrainment into an aspirated canister is limited. The purpose of this study is to provide quantitative information about the aspirated mass-flow rate during airbag deployment. Pressure and velocity measurements are combined with high-speed photography in order to gain further insight into the relationship between the canister pressure, the rate of cabin-air entrainment and the airbag deployment.

This paper documents the development process of the 2001 Pontiac Aztek body structure for improved noise & vibration performance. Successful vehicle development under an accelerated timing schedule demands clearly defined body structure vibration performance targets and critical dependence on the math based modeling process. Specifications for global body structure vibration performance were generated through a two step process. First, a benchmarking activity was undertaken to comprehend competitive vehicle performance. Secondly, a frequency domain “mode map” was constructed to minimize vehicle subsystem interaction. Computer simulation models were developed to predict the body structure performance. A coarse full body structure model was used to define body structure section size and joint requirements. Detailed analysis models of body joint areas were used to synthesize the joint design.

In performing stochastic simulations using computer models, the method of sampling is important. It affects the quality and the convergence speed of the results. This paper discusses one special case: sampling of spot-weld locations from potentially thousands of spot welds on a vehicle body. This study is prompted by the need of evaluating the effect of missed spot welds on the structural integrity, identifying critical welds, and optimizing weld locations. A balanced random sampling algorithm based on the concept of Latin-Hypercube sampling is developed for this application. We also present a case study in which the efficiency of three different sampling methods is compared using a car joint stiffness example. The new method, called the Balanced Latin-Hypercube Sampling (BLHS), has shown significantly faster convergence over the other two.

The approaches used to develop an NVH package for a vehicle have changed dramatically over the last several years. New noise and vibration control strategies have been introduced, new materials have been developed, advanced testing techniques have been implemented, and sophisticated computer modeling has been applied. These approaches help design NVH solutions that are optimized for cost, performance, and weight. This paper explains the NVH practices available for use in designing vehicles for the new millennium.

Indoor or laboratory testing of tire tread wear offers many advantages over vehicle fleet testing. Advances in test equipment capabilities and the technologies for defining and simulating meaningful tire loading histories has made indoor tread wear testing a reality. Tire loading histories are influenced by vehicle characteristics, wear course and driving style, and tire stiffnesses. Methods for independently characterizing each of these are reviewed. A simulation technique, TS-Sim, is also described that combines specific vehicle, course and tire characterizations to create a tire load history. The vehicle characterization is critical to the process since both wear rate and various forms of uneven and irregular wear are strongly dependent on vehicle suspension/steering characteristics and on dynamic load transfer behavior. The characterization process involves mapping the vehicle over a practical range of acceleration, deceleration and cornering maneuvers.

This paper discusses an analytical technique for computing the failure rate of steel springs used in automotive part applications. Preliminary computations may be performed and used to predict spring failure rates quickly at a very early stage of a product development cycle and to establish program reliability impact before commitment. The analytical method is essentially a combination of various existing procedures that are logically sequenced to compute a spring probability of failure under various operational conditions. Fatigue life of a mechanical component can be computed from its S-N curve. For steels, the S-N curve can be approximated by formulae which describe the fatigue life as a function of its endurance limit and its alternating stress. Most springs in service are preloaded and the actual stress fluctuates about a mean level. In order to compute an equivalent alternating stress with zero mean, an analytical method based on the Goodman Diagram is used.

CHEVROLET has made its new air-suspension system easily interchangeable in production line assembly with standard full-coil suspension by adopting a 4-link-type rear suspension with short and long arms. A feature of the system is the mounting of the leveling valves within the air-spring assemblies. These valves correct riding height continually at a moderate rate, regardless of whether the springs are leveling or operating in ride motion. The system provides constant frequency ride—ride comfort remains the same whether the car is occupied by the driver alone or is fully loaded.