Search Results

Since the sizes of the flywheel and clutch have been enlarged due to downsizing of diesel engines, the mass and moment of inertia at the crankshaft rear end have increased. Consequently, the serious bending stresses have appeared in the crankshaft rear. This paper describes the characteristics of those serious bending stresses, based on the mechanism for whirl resonance. The whirl resonance is largely impacted by the mass of the flywheel and clutch and by the distance from the crank-journal center of the rear end to the center of gravity of the flywheel and clutch.

In recent years, Nearfield Acoustical Holography (NAH) has been used to identify stationary vehicle exterior noise sources. However that application has usually been limited to individual components. Since powertrain noise sources are hidden within the engine compartment, it is difficult to use NAH to identify those sources and the associated partial field that combine to create the complete exterior noise field of a motor vehicle. Integrated Nearfield Acoustical Holography (INAH) has been developed to address these concerns: it is described here. The procedure entails sensing the sources inside the engine compartment by using an array of reference microphones, and then calculating the associated partial radiation fields by using NAH. In the second part of this paper, the use of farfield arrays is considered. Several array techniques have previously been applied to identify noise sources on moving vehicles.

Since powertrain noise sources are usually “hidden” within the engine compartment, it is difficult to use NAH to identify those sources and the associated partial radiation fields that together create the exterior noise field of a motor vehicle. Integrated Nearfield Acoustical Holography (INAH) has been developed to address this concern. INAH represents a combination of NAH, reference microphone selection procedures, and coherence techniques. The procedure entails sensing the sources inside the engine compartment by using an array of reference microphones, and then calculating the associated partial radiation fields by using NAH. A key factor in the success of this procedure is the selection of a good reference microphone sub-set. A selection procedure has been developed by combining condition number and coherence analyses. The partial field determination problem has been approached by using both partial coherence and Singular Value Decomposition (SVD) procedures.

Every year the trucking industry demands lighter weight and lower cost truck components. But it is very difficult to achieve both these targets. This paper describes the example of a suspension system design which was conducted by computer simulation, so called CAE. The computer simulation by FEM was used completely to decide the detailed shape of each part. This paper also introduces a casting method to strengthen the aluminum alloy cast using high pressure during casting. By using this method, products have a precise metallographic structure. As a result, both the development cost and period were reduced by over the half the time required of the current system and lighter and strong parts were created.

There are many methods for case hardening such as conventional induction hardening and newly developed electron beam hardening. Electron beam hardening has been adopted in Isuzu and the reliability of engines has been improved. The beam power of the electron beam hardening equipment used was 6 kW. Various conditions of electron beam were scanned across specimens (SCM435H) in order to investigate the influence on hardening properties. As a result, relation between case depth and beam current and relation between case depth and beam scanning time were confirmed. And when the depth exceeded 1 mm, there were cracks in surface melted area. Electron beam hardening was applied to tappets according to the above fundamental experiments, and uniformly hardened layers were obtained. Durability of engines with electron beam hardened tappets was improved twice as much as those with non-hardened tappets.

There is ever an increasing need for weight reduction and high performance of engine (clean smoke and improving fuel economy) To achieve this, recently aluminum castings are used for engine parts such as cylinder heads that construct combustion chamber and are required thermal resistance. This paper describes thermal fatigue tests of aluminum castings that are made under various conditions of cooling rate during solidification, heat treatment, and chemical compositions. It further investigates the influence of material (such as cooling rate, chemical conmposition and heat treatment) and mechanical properties (such as σB, δ, E ) on thermal fatigue life of aluminum castings.

Countour Induction Hardening (CIH) method is in the limelight as a new possible surface refining method for gears as it reduces quenching distortion considerably and increases compressive residual stress. Also, Double Shot Peening (DSP) method, especially its advanced technique of using extensively small shots (less than 100 m) at the secondary peening, enables increased compressive residual stress under the surface of the gears. Therefore, the new Compound Surface Refining Method of using CIH + DSP is expected to give much higher compressive residual stress than the conventional methods. On studying the application of this new method, the authors evaluated their surface-refining characteristics and the fatigue limits.

A torsional damper is attached to a crankshaft to control the torsional vibration of the crankshaft system. However, the damper, which has a rubber part in between a damper mass and a damper hub, possesses a three-dimensional inertia moment and an inertia mass that could excite the crankshaft system. This paper discusses the generating mechanisms of the bending strain on the bolt to fasten the damper hub to the crankshaft, from the measured bolt strains and the measured behavior of the damper mass and the damper hub under the engine operating conditions.

Equations of motion with six degrees of freedom are composed of detailed dimensions of vehicle, suspension, steering and tire, which must be determined at the designing stage. Particularly, in the dyamics of suspension system, the hypothesis of fixed roll axis are excluded. And, instead, the effect of side force which affects rolling and vertical motion of the vehicle is introduced on the basis of geometrical variation of the tire's contact points. In addition, a number of equations including the cornering force of tire are treated in nonlinear method, with the effect of driving and braking forces being taken into account at the same time. This analysis has enabled strict interpretation of cornering characteristics. However this article is devoted mainly to the analysis of various phenomena which take place in critical situations responsible for accidents in cornering, resultant from spin-out, drift-out, wheel-lift (jack-up) and roll-over.

Vibration behavior of a crankshaft in operation is complicated and difficult to simulate because of oil effects on journals, coupled vibration of crankshaft system parts, combustion and inertia acting on the crankshaft. Particularly, the stiffness and damping of oil film vary with crank angles and thus the numerical analysis must deal with nonlinear vibration. This oil film effects also diversify the vibration modes of the crankshat; the vibration modes in an actual operation differs from that in statically experiment modal analysis. This paper describes a new method developed by the author to analyses, predict, and reduce noise and vibration using several techniques including numerical simulation, finite element method, Sommerfeld concept on oil film effects, and modal frequency response.