Search Results

To meet corporate CO2 emission targets polymer composites are being explored for light-weighting vehicle applications. Operational requirements may demand that such materials function above glass transition temperatures or heat deflection points. Intumescent coatings are traditionally used in construction to protect steelwork during fire. This paper presents a novel experimental investigation of two intumescent technologies to thermally protect a reinforced polyamide, for use as a semi-structural vehicle component. Coatings were assessed against the thermal requirement to withstand 500°C for 10 minutes. The differences in performance observed between water and epoxy based coatings as well as when an insulation layer was introduced are reported. Ultimate Tensile Stress (UTS) and modulus values were obtained at −40°C, ambient, and 85°C for uncoated specimens before and after thermal cycling.

The in-cabin sound pressure level response of a vehicle in yawed wind conditions can differ significantly between the smooth flow conditions of the aeroacoustic wind tunnel and the higher turbulence, transient flow conditions experienced on the road. Previous research has shown that under low turbulence conditions there is close agreement between the variation with yaw of in-cabin sound pressure level on the road and in the wind tunnel. However, under transient conditions, sound pressure levels on the road were found to show a smaller increase due to yaw than predicted by the wind tunnel, specifically near the leeward sideglass region. The research presented here investigates the links between transient flow and aeroacoustics. The effect of small geometry changes upon the aeroacoustic response of the vehicle has been investigated.

Sports Utility Vehicles (SUVs) typically have a blunt rear end shape (for design and practicality), however this is not beneficial for aerodynamic drag. Drag can be reduced by a number of passive and active methods such as tapering and blowing into the base. In an effort to combine these effects and to reduce the drag of a visually square geometry slots have been introduced in the upper side and roof trailing edges of a squareback geometry, to take air from the freestream and passively injects it into the base of the vehicle to effectively create a tapered body. This investigation has been conducted in the Loughborough University’s Large Wind Tunnel with the ¼ scale generic SUV model. The basic aerodynamic effect of a range of body tapers and straight slots have been assessed for 0° yaw. This includes force and pressure measurements for most configurations.

Vehicles on the road operate in the turbulent flow field resulting from the combined effects of the natural wind and the wakes of other vehicles. While substantial data exists on the properties of the natural wind, much less information is available for the wake properties of road vehicles. The wake information available for road vehicle shapes is mainly restricted to the near wake region, but to understand the vehicle operating environment it is the wake downstream of this region which is of interest. To determine the range of this area of interest requires some knowledge of the decay of the wake properties. From wind tunnel studies using small simple bluff bodies in free stream and in ground proximity the principle wake properties, velocity deficit and peak turbulence intensity have been measured. The maximum velocity deficit is shown to approximately decay with x-2/3, where x is the distance downstream, while turbulence intensity decays at a slightly slower rate.

Numerical simulation of aerodynamics for vehicle development is used to meet a wide range of performance targets, including aerodynamic drag for fuel efficiency, cooling flow rates, and aerodynamic lift for vehicle handling. The aerodynamic flow field can also be used to compute the advection of small particles such as water droplets, dust, dirt, sand, etc., released into the flow domain, including the effects of mass, gravity, and the forces acting on the particles by the airflow. Previous efforts in this topic have considered the water sprays ejected by rotating wheels when driving on a wet road. The road spray carries dirt particles and can obscure the side and rear glazing. In this study, road sprays are considered in which the effects of additional water droplets resulting from splashing and dripping of particles from the wheel house and rear under body are added to help understand the patterns of dirt film accumulation on the side glass and rear glass.

Testing real-time vehicular systems challenges the tester to design test cases for concurrent and sequential input events, emulating unexpected user and usage profiles. The vehicle response should be robust to unexpected user actions. Sequence Covering Arrays (SCA) offer an approach which can emulate such unexpected user actions by generating an optimized set of test vectors which cover all possible t-way sequences of events. The objective of this research was to find an efficient nonfunctional sequence testing (NFST) strategy for testing the robustness of real-time automotive embedded systems measured by their ability to recover (prove-out test) after applying sequences of user and usage patterns generated by combinatorial test algorithms, considered as “noisy” inputs. The method was validated with a case study of an automotive embedded system tested at Hardware-In-the-Loop (HIL) level. The random sequences were able to alter the system functionality observed at the prove-out test.

Over the past decade there have been significant advances made in the technology used to engineer Powertrain Sound Quality into automobiles. These have included exhaust system technologies incorporating active and semi-active valves, intake system technologies involving passive and direct feedback devices, and technologies aimed at tuning the structure-borne content of vehicle interior sound. All of these technologies have been deployed to complement the traditional control of NVH issues through the enhancement of Powertrain Sound Quality. The aim of this paper is to provide an historical review of the recent industry-wide advances made in these technologies and to provide the author's perspective on what issues have been addressed and what opportunities have been delivered.

A novel semi-analytical solution has been developed for the calculation of the static and dynamic response of an off road tire interacting with a deformable terrain, which utilizes soil parameters independent of the size of the contact patch (size-independent). The models involved in the solution presented, can be categorized in rigid and/or pneumatic tires, with or without tread pattern. After a concise literature review of related methods, a detailed presentation of the semi-analytical solution is presented, along with assumptions and limitations. A flowchart is provided, showing the main steps of the numerical implementation, and various test cases have been examined, characterized in terms of vertical load, tire dimensions, soil properties, deformability of the tire, and tread pattern. It has been found that the proposed model can qualitatively capture the response of a rolling wheel on deformable terrain.

Market demand for high performance gasoline vehicles and increasingly strict government emissions regulations are driving the development of highly downsized, boosted direct injection engines. The in-cylinder temperatures and pressures of these emerging technologies tend to no longer adhere to the test conditions defining the RON and MON octane rating scales. This divergence between fuel knock rating methods and fuel performance in modern engines has previously led to the development of an engine and operating condition dependent scaling factor, K, which allows for extrapolation of RON and MON values. Downsized, boosted DISI engines have been generally shown to have negative K-values when knock limited, indicating a preference for fuels of higher sensitivity and challenging the relevance of a lower limit to the MON specification.

This paper presents a series of observations of time-averaged wake asymmetry for a range of “notchback” vehicle geometries. The primary focus is on a reduced scale experiment using full-sized saloon geometry. Substantial flow asymmetry was observed in the vehicle “notch”. Similar asymmetries are reported for a full scale experiment on the same geometry along with others as diverse as production models of a luxury and mid-sized saloon; basic car shapes and a simple body. In one case a physical explanation is proposed, based on the degeneration of an unstable symmetric wake structure.

2, 5-Dimethylfuran (DMF) has been receiving increasing interest as a potential alternative fuel to fossil fuels, owing to the recent development of new production technology. However, the influence of DMF properties on the in-cylinder fuel spray and its evaporation, subsequent combustion processes as well as emission formation in current gasoline direct injection (GDI) engines is still not well understood, due to the lack of comprehensive understanding of its physical and chemical characteristics. To better understand the spray characteristics of DMF and its application to the IC engine, the fuel sprays of DMF and gasoline were investigated by experimental and computational methods. The shadowgraph and Phase Doppler Particle Analyzer (PDPA) techniques were used for measuring spray penetration, droplet velocity and size distribution of both fuels.

Water accumulating on a vehicle's wind screen, driven over the A-pillar by a combination of aerodynamic forces and the action of the windscreen wipers, can be a significant impediment to driver vision. Surface water film, or streams, persisting in key vision areas of the side glass can impair the drivers' ability to see clearly through to the door mirror, and laterally onto junctions. Common countermeasures include: water management channels and hydrophobic glass coatings. Water management channels have both design and wind noise implications. Hydrophobic coatings entail significant cost. In order to manage this design optimisation issue a water film and wiper effect model has been developed in collaboration with Jaguar Land Rover, extending the capabilities of the PowerFLOW CFD software. This is complimented by a wind-tunnel based test method for development and validation. The paper presents the progress made to date.

With the growing complexity of, and reliance on, safety-related electrical/electronic (E/E) systems in the automotive sector, the development of an explicit safety case is highly recommended to provide assurance to the different stakeholders interested in automotive functional safety. The production of a safety case is explicitly mandated by the draft automotive functional safety standard ISO26262. A safety case should consider all organisational and technical factors that may contribute to safety. For example, it should provide assurance for the safe behaviours of a particular system as well as assurance for the process by which this system is developed, operated and maintained. In this paper, we address one component of the overall safety case, namely the assurance of the functional safety concept. In particular, we examine how model-driven development and assessment can provide a basis for the systematic generation of functional safety requirements.

Under bonnet thermal encapsulation is a method for retaining the heat generated by a running powertrain after it is turned off. By retaining the heat in the engine bay, the powertrain will be closer to its operating temperatures the next time it is started, reducing the warm up time required. This reduces the period of inefficiency due to high friction losses before the engine reaches it operating temperature, and as a result reduces the vehicles fuel consumption and CO2 emissions. To develop an integrated and efficient encapsulation design, CAE methods can be applied to allow this work stream to start as early in a vehicles development cycle as possible. In this work, the existing test methods are discussed, and a new Thermal CFD method is presented that accurately simulates the fluid temperatures after a customer representative 9 hour park period.

A prototype multi-hole diesel injector operating with n-heptane fuel from a high-pressure common rail system is used in a high-pressure and high-temperature test rig capable of reaching 1100 Kelvin and 150 bar under different oxygen concentrations. A novel optical set-up capable of visualizing the soot cloud evolution in the fuel jet from 30 to 85 millimeters from the nozzle exit with the high-speed color diffused back illumination technique is used as a result of the insertion of a high-pressure window in the injector holder opposite to the frontal window of the vessel. The experiments performed in this work used one wavelength provide information about physical of the soot properties, experimental results variating the operational conditions show the reduction of soot formation with an increase in injection pressure, a reduction in ambient temperature, a reduction in oxygen concentration or a reduction in ambient density.

The rotor and stator of electric motors consist of multiple materials, of which steel forms the majority of mass and volume. Steel in electric motors is commonly in the form of thin sheets (laminations), stacked along the axis of the rotor. The structural integrity of such a stack can be ensured using bolting, welding or bonding of the laminations. Predictive mechanical finite element simulations of these laminated stacks can become computationally intense because the steel sheets are thin, and the motor often contains hundreds of them. If the laminations are modelled individually, the size of the elements is very small compared to the overall dimensions and the interface between the laminations need to be modelled as well. In this paper, we present an alternate method of modelling this laminated stack as a single solid body using homogeneous and orthotropic material property, instead of representing each lamination.

Little research has been done on spray characteristics of 2,5-dimethylfuran (DMF), since the breakthrough in its production method as an alternative fuel candidate. In this paper, the spray characteristics of pure fuels (DMF, Isooctane) and DMF-Isooctane blends under different ambient pressures (1 bar, 3 bar and 7 bar) and injection pressures (50 bar, 100 bar and 150 bar) were studied using Phase Doppler Particle Analyzer (PDPA) and high speed imaging. Droplet velocity, size distribution, spray angle and penetration of sprays were examined. Based on the results, DMF had larger SMD and penetration length than isooctane. The surface tension of fuel strongly influenced spray characteristics. Increasing the surface tension by 26 % resulted in 12 % increase in SMD. Higher ambient pressure increased the drag force, but SMD was not influenced by the increased drag force. However, the increased ambient pressure reduced the injection velocity and We number resulting in higher SMD.

Predicting Exterior Water Management is important for developing vehicles that meet customer expectations in adverse weather. Fluid film methods, with Lagrangian tracking, can provide spray and surface water simulations for complex vehicle geometries in on-road conditions. To cope with this complexity and provide practical engineering simulations, such methods rely on empirical sub-models to predict phenomena such as the film stripping from the surface. Experimental data to develop and validate such models is difficult to obtain therefore here a high-fidelity Coupled Level-set Volume of Fluid (CLSVOF) simulation is carried out. CLSVOF resolves the interface of the liquid in three dimensions; allowing direct simulation of film behaviour and interaction with the surrounding air. This is used to simulate a simplified wing-mirror, with air flow, on which water is introduced.

The introduction of Bharat Stage VI emissions level (BSVI) emission directives, the upcoming corporate average fuel economy (CAFE) regulations, and the ever-increasing cost of fuel have been bringing more focus, research and development (R&D) efforts into improving engine efficiency, fuel economy, performance and reducing carbon dioxide (CO2) emissions. The Worldwide harmonized Light vehicles Test Procedure (WLTP) emissions regulation, Worldwide harmonized Light vehicles Test Cycles (WLTC) and Real Driving Emissions (RDE) have been introduced. Active grille shutter (AGS) design and implementation has been discussed in this paper, a work that Tata Motors European Technical Centre (TMETC) has led for Tata Motors, and we have found that it improves the vehicle fuel economy in the real world. This work has been a part of the bouquet of programs TMETC is championing as a part of the new vehicle and powertrain technology introduction.

The notion of open source systems has been well established in systems software and typified by the development of the Linux operating system. An open source community is a community of interest that makes use of software tools in research and development. Their ongoing development is part of the free flow of ideas on which the community. The motivation for the work reported in this paper is to provide the research community in engine controls with a ready access to a complete engine management solution and the component parts. The work described in this paper extends open source principles to engine control with a portable spark ignition (SI) control strategy assembled using Simulink. The underlying low level drivers are written in C and designed for portability. A calibration tool is written in C and works over a controller area network (CAN) link to the engine control unit (ECU). The ECU hardware is based on the Infineon Tricore microcontroller.