Search Results

Appropriate emergency response information is required for first responder before hydrogen fuel cell vehicles will become widespread. This paper investigates experimentally the hydrogen dispersion in the vicinity of a vehicle which accidentally releases hydrogen horizontally with a single volumetric flow of 2000 NL/min in the under-floor section while varying cross and frontal wind effects. This hydrogen flow rate represents normally a full throttle power condition. Forced wind was about maximum 2 m/s. The results indicated that the windward side of the vehicle was safe but that there were chiefly two areas posing risks of fire by hydrogen ignition. One was the leeward side of the vehicle's underbody where a larger region of flammable hydrogen dispersion existed in light wind than in windless conditions. The other was the area around the hydrogen leakage point where most of the leaked hydrogen remained undiffused in an environment with a wind of no stronger than 2 m/s.

The localized fire test provided in the Global Technical Regulation for Hydrogen Fuel Cell Vehicles gives two separate test methods: the ‘generic installation test - Method 1′ and the ‘specific vehicle installation test - Method 2′. Vehicle manufacturers are required to apply either of the two methods. Focused on Method 2, the present study was conducted to determine the characteristics and validity of Method 2. Test results under identical burner flame temperature conditions and the effects of cylinder protection covers made of different materials were compared between Method 1 and Method 2.

To verify the appropriateness of the vibration test conditions of ISO 12405, we performed tailoring to derive power spectrum densities and test durations as vibration test conditions. Vehicles used for tailoring included two electric vehicles and one plug-in hybrid electric vehicle. Those vehicles were equipped with accelerometers and were run on seven different road types at different speeds while data on the acceleration of the battery packs were recorded. The power spectrum densities for three axes that were derived from the obtained acceleration data were similar in form to the power spectrum densities of ISO 12405, and almost the same root mean square accelerations were obtained, confirming that they are appropriate. However, both experiments and theory suggest that the test duration for the Z-axis exceeds those of the X- and Y-axes.

Recently, for passenger cars, hand operated gearshift systems have been made available by some manufacturers for the purpose of easy gearshift operation and to make driving more fun. For adapting such a system to an ATV (All Terrain Vehicle), which is used mainly for agriculture and leisure, the whole system should be compact and lightweight. It is also necessary for the clutch to be engaged properly under various running conditions. This gearshift system performs both engaging and disengaging of the clutch and moving the gearshift spindle with one motor. Since this system is controlled by calculated engine speed, vehicle speed and gear position, suitable gear shifting is realized under various running conditions. For optimal clutch control, there is a reversing point for the decreasing and increasing of engine speed for each gearshift. This accelerates the clutch engagement speed and makes quick returning of the gearshift spindle.

In order to clarify future automobile technologies and fuel qualities to improve air quality, second phase of Japan Clean Air Program (JCAPII) had been conducted from 2002 to 2007. Predicting improvement in air quality that might be attained by introducing new emission control technologies and determining fuel qualities required for the technologies is one of the main issues of this program. Unregulated material WG of JCAPII had studied unregulated emissions from gasoline and diesel engines. Eight gaseous hydrocarbons (HC), four Aldehydes and three polycyclic aromatic hydrocarbons (PAHs) were evaluated as unregulated emissions. Specifically, emissions of the following components were measured: 1,3-Butadiene, Benzene, Toluene, Xylene, Ethylbenzene, 1,3,5-Trimethyl-benzene, n-Hexane, Styrene as gaseous HCs, Formaldehyde, Acetaldehyde, Acrolein, Benzaldehyde as Aldehydes, and Benzo(a)pyrene, Benzo(b)fluoranthene, Benzo(k)fluoranthene as PAHs.

Water management is one of the key factors to ensure high performance, cold start and durability of polymer electrolyte fuel cells (PEFCs), and it is important to understand the behavior of liquid water in PEFCs. X-ray computed tomography (X-ray CT) imaging and the two-phase lattice Boltzmann method (two-phase LBM) are applied to analyze the mechanism of water transport in the gas diffusion layers (GDLs) and the gas channels in generating PEFCs. The results of the two-phase LBM are compared with those of X-ray CT imaging, and are found to agree qualitatively in that water is discharged along the hydrophilic channel wall and accumulated in the GDL, especially under the rib. The effects of the wettability of the GDLs, and of the gas channels, the diameter of the carbon fibers, and the porosity of the GDLs on water discharge from the GDLs and gas channels are also investigated.

The current hydrogen storage systems for fuel-cell vehicles are mainly a compressed hydrogen storage type, but it is known that the temperature inside the tank commonly increases while the tank is being filled with hydrogen. This study examines filling methods that prevent the temperature from exceeding the designed temperature of the tank. In order to propose a filling method that suppresses the temperature rise inside the tank and achieves filling within a short time, fast-filling tests were conducted on test tanks designed for fast filling of fuel cell vehicles. The detailed influences of the differences in type of tank and filling pressure on the rate of the internal temperature increase were investigated. Thermal responses were measured at various parts inside and outside the tank while varying the filling pressure, type of tank, tank capacity, filling time, and filling pattern, using a test tank that allows multi-point measurement of the internal temperature.

If a compressed hydrogen tank for vehicles is filled with hydrogen gas more quickly, the gas temperature in the tank will increase. In this study, we conducted hydrogen gas filling tests using the TYPE 3 and TYPE 4 tanks. During the tests, we measured the temperature of the internal liner surface and investigated its relationship with the gas temperature in the tank. We found that the gas temperature in the upper portion of the TYPE 4 tank rose locally during filling and that the temperature of the internal liner surface near that area also rose, resulting in a temperature higher than the gas temperature at the center of the tank. To keep the maximum temperature in the tank below the designed temperature (85°C) during filling and examine the representative tank internal temperatures, it is important to examine filling methods that can suppress local rises of tank internal temperature.

In recent years, Eeletoric Vehicle attracts attention as the favorite in a next-generation car. Various factors called promotion of the problem of drain of a fossil fuel, global warming, and next-generation industry exist in this background. In this paper, by arranging these factors on many sides and carrying out them considers the directivity to which EV should progress.

In recent years, the increased use of electric power steering in vehicles has increased the importance of issues such as making systems more compact and lightweight, and dealing with increased development man-hours. To increase development efficiency, the use of a “Hardware in the loop simulator” (HILS) is being tested to shift from the previous development method that relied on a driver's subjective evaluation in an actual vehicle test to bench-test development. Using HILS enables tasks such as specification studies, performance forecasts, issue identification and countermeasure proposals to be performed at an early stage of development even when there is no prototype vehicle. This report describes a case study of using HILS to solve the issues of reducing the load by adjusting the geometric specifications around the kingpin and eliminating the tradeoff by adding a new EPS control algorithm in order to make the electric power steering (EPS) more compact and lightweight.

The moment of inertia of the crankshaft cannot be ignored when analyzing the dynamics of a motorcycle. In this research, the tire friction force (calculated by drag and tire side force) was used as an index of the drive performance. The ratio of roll rate and steering torque (here after referred to as a roll rate gain) was used as an index of the cornering performance, and it was analyzed as the influence of the moment of inertia of a crankshaft on the drive performance as well as cornering performance. As a result, the influence on drive performance and cornering performance by the moment of inertia has been found.

Results are presented from an experimental study of the effects of engine speed and injection pressure transients on the cold start performance of a gasoline direct injection engine operating on iso-octane. The experiments are performed in an optically-accessible single-cylinder research engine modified for gasoline direct injection operation. In order to isolate the effects of the engine speed and injection pressure transients, three different cold start simulations are used. In the first cold start simulation the engine speed and injection pressure are constant. In the second cold start simulation the injection pressure is constant while the engine speed transient of an actual cold start is simulated. In the third cold start simulation both the engine speed and the injection pressure transients of an actual cold start are simulated.

The reduction of fuel consumption is of great importance to automobile manufacturers. As a prospective means to achieve fuel economy, lean burn is being investigated at various research organizations and automobile manufacturers and a number of studies on lean-burn technology have been reported to this date. This paper describes the development of a four-valve lean-burn engine; especially the improvement of the combustion, the development of an engine management system, and the achievement of vehicle test results. Major themes discussed in this paper are (1) the improvement of brake-specific fuel consumption under partial load conditions and the achievement of high output power by adopting an optimized swirl ratio and a variable-swirl system with a specially designed variable valve timing and lift mechanism, (2) the development of an air-fuel ratio control system, (3) the improvement of fuel economy as a vehicle and (4) an approach to satisfy the NOx emission standard.

We had developed Electric Servo Brake System, which can control brake pressure accurately with a DC motor according to brake pedal force. Therefore, the system attains quality brake feeling while reflecting intentions of a driver. By the way, “Build-up” is characteristics that brake effectiveness increases in accordance with the deceleration of the vehicle, which is recognized as brake feeling with a sense of relief as not to elongate an expected braking distance at a downhill road due to large-capacity brake pad such as sports car and large vehicles. Then, we have applied the optical characteristic control to every car with Electric Servo Brake System by means of brake pressure control but not brake pad. Hereby, we confirmed that the control gives a driver the sense of relief and the reduction of pedal load on the further stepping-on of the pedal. In this paper, we describe the development of brake feel based on the control overview.

Test procedures for evaluating vehicle compatibility were investigated based on accident analysis and crash tests. This paper summarizes the research reported by Japan to the IHRA Compatibility Working Group. Passenger cars account for the largest share of injuries in head-on collisions in Japan and were identified as the first target for tackling vehicle compatibility in Japan. To ascertain situations in collisions between vehicles of different sizes, we conducted crash tests between minicars and large cars, and between small cars and large cars. The deformation and acceleration of the minicar and small car is greater than that of large car. ODB, Overload and MDB tests were performed as procedures for evaluating vehicle compatibility. In overload tests, methods to evaluate the strength of the passenger compartment were examined, and it is found that this test procedure is suitable for evaluating the strength of passenger compartments.

In a previous study by the authors, austenite (γ phase) formed on the topmost of pulleys after long term operation of continuously variable transmission (CVT) [1]. In general, martensite arising from heat treatment forms on the surface of pulleys and gears. Therefore, the sliding surface has a body-centered cubic (BCC) metal structure, and transformation into and existence of austenite (γ phase) is difficult unless there is a thermal history exceeding the eutectoid point. For the verification of that possibility, it was crucial to obtain temperature variation on the sliding surface. The major problem for such measurements was rotation of parts inside an operating CVT. In this study, uniquely developed measurement system enabled non-contact temperature measurement near the contact portion. Results were substituted to heat conduction equation to predict the temperature at the exact contact portion.

Honda's technology applied to CR-Z HEV propulsion system. Presenter Takeo Nishibori, Honda R&D Co., Ltd.

Honda R&D has developed a throttle-by-wire (TBW) system that meets the needs of motorcycles where the attitude of the vehicle body is controlled by operation of the throttle. To gain high response and following for the throttle valve, we employed a new adaptive control algorithm. The newly developed system has an idling combustion stabilization function and a three-dimensional control function for the throttle-opening map based on running gear and engine speed. With those functions, we improved the controllability of the motorcycle, especially for small throttle openings. Furthermore, we improved the feeling of the limiter control used in maximum-speed limitation. For the overall system, intake system related devices are consolidated to improve the layout flexibility and expand the mounting options on the motorcycle.

Diesel emissions are significant issue worldwide, and emissions requirements have become so tough that. the application of after-treatment systems is now indispensable in many countries To meet even more stringent future emissions requirements, it has become apparent that the improvement of market fuel quality is essential as well as the development in engine and exhaust after-treatment technology. Japan Clean Air Program II (JCAP II) is being conducted to assess the direction of future technologies through the evaluation of current automobile and fuel technologies and consequently to realize near zero emissions and carbon dioxide (CO2) emission reduction. In this program, effects of fuel properties on the performance of diesel engines and a vehicle equipped with two types of diesel NOx emission after-treatment devices, a Urea-SCR system and a NOx storage reduction (NSR) catalyst system, were examined.

The measuring method of vehicular particulate matter (PM) size distribution to simulate the atmospheric dilution process was studied. PM size distribution was measured with a scanning mobility particle sizer (SMPS). To simulate the atmospheric dilution process with a chassis dynamometer test, a chasing experiment was done in order to obtain reference data. A light duty diesel truck was selected as a basic test vehicle. Three sizes of prototype partial flow diluters (PPFD) were made to reproduce the PM size in the atmosphere. The PM sizes of the chasing experiment and the PPFD experiment was roughly agreed. Differences in the data obtained from a full flow dilution tunnel and the chasing experiments were investigated. The length of the transfer tube greatly affected the smaller side of the PM number concentration.