Search Results

Historically, the long development time required to produce a new automobile has meant that the electronics in that vehicle might lag the state-of-the-art by several years. For traditional vehicle electronics, this was certainly an appropriate delay, ensuring through extensive testing and qualification that the quality and reliability of the electronic systems met rigorous standards. However, with the growing consumer-oriented electronics content in today's vehicles, it is becoming more difficult for the automotive manufacturers to meet consumers' expectations with older technology. Couple this with the fast-paced consumer product cycle, typically nine to eighteen and the result is increasing pressure on the vehicle manufacturers from after-market electronics suppliers, who can update their product lines as fast as the component manufacturers can produce new models.

Extending engine-oil-change intervals is of interest from the standpoint of reducing used oil disposal and reducing time and expense of maintenance. However, the oil must be changed before serious oil degradation and engine damage occur. Three variables which influence oil degradation were chosen for investigation: base oil composition (synthetic oil versus mineral oil), trip length (short trips versus long trips), and driving schedule (degrading an oil during a given type of service, then changing to another type of service without an intervening oil change). Analysis of oil samples taken throughout the testing program indicated that type of service (freeway compared to short trip) influenced oil degradation to a greater extent than oil type. That is, API SG-quality synthetic oil in short-trip service degraded faster than borderline SG-quality mineral oil in long-trip service.

In order to engineer Squeak & Rattle (S&R) free vehicles it is essential to develop an objective measurement method to compare and correlate with customer satisfaction and subjective S&R assessments. Three methods for exciting S&Rs -type surfaces. Excitation methods evaluated were road tests over S&R surfaces, road simulators, and direct body excitation (DBE). The principle of DBE involves using electromagnetic shakers to induce controlled, road-measured vibration into the body, bypassing the tire patch and suspension. DBE is a promising technology for making objective measurements because it is extremely quiet (test equipment noise does not mask S&Rs), while meeting other project goals. While DBE is limited in exposing S&Rs caused by body twist and suspension noises, advantages include higher frequency energy owing to electro-dynamic shakers, continuous random excitation, lower capital cost, mobility, and safety.

As the driving population ages, there is a need to understand the accident patterns of older drivers. Previous research has shown that side impact collisions, usually at an intersection, are a serious problem for the older driver in terms of injury outcome. This study compares the frequency of side impact, intersection collisions of different driver age groups using state and national police-reported accident data as well as an in-depth analysis of cases from a fatal accident study. All data reveal that the frequency of intersection crashes increases with driver age. The state and national data show that older drivers have an increase frequency of intersection crashes involving vehicles crossing paths prior to the collision compared to their involvement in all crash types. When taking into account traffic control devices at an intersection, older drivers have the greatest involvement of multiple vehicle crashes at a signed intersection.

During braking, the ability to utilize available tire-road friction is determined by brake balance. Previous methods for objectively measuring balance require various degrees of vehicle instrumentation and modification. The Road Transducer is a new measurement technique based on instrumented sections of roadway. Individual braking forces developed by each wheel are measured without vehicle instrumentation, modification, or special set up. This facilitates assessment of many vehicles required for statistical analyses. Brake balance data for several hundred vehicles are presented and provide insight to the nominal levels and variability of braking efficiencies found in the field.

This paper presents the computer vision-based V2X collaborative perception. Our system uses a forward-looking camera in the host vehicle. The camera detects road users such as pedestrians, vehicles, and motorcycles. Such information includes object type, relative location, direction, and speed. This information is used to compose proxy Basic Safety Messages on behalf of the detected objects. Early adopters of the V2X technology can experience the benefits of enhanced V2X market penetration. The outcome of adopting this concept will result in an inflated V2X market penetration rate leading to earlier safety, mobility, and situational awareness improvements. The ultimate goal is for all road participants to be fully aware of each other. The novelty of our work is the integration of computer vision-based detection and LTE-V V2X communications, in addition to implementing the concept for pedestrians and bicyclists.

Many studies have been done to objectively measure car seat foam properties and correlate them to comfort performance. Typically, the vibration characteristics (namely transmissibility) of the foam cushion are measured. It has been generally accepted that low natural frequency equates to better comfort. However, no subjective studies have been done to verify that humans can feel the vibration differences that are measured. Also, the measured differences of the foam may not be detectable once the foam is built into a complete seat. Three different foam formulations utilizing MDI (methylene diphenyl diisocyanate) and TDI (toluene diisocyanate) technology were evaluated for vibration characteristics. The foams were then submitted to subjective human testing and objective lab testing after being built into seats. The subjective testing was done using a typical ride and drive evaluation where people were interviewed about the comfort of the seat while driving over various road conditions.

The Cadillac Electronic Climate Control heating and air conditioning system provides automatic control of the passenger compartment temperature. It utilizes a microcomputer to control the operation of electrical, mechanical and vacuum components that regulate the amount and temperature of air delivered into the car to maintain the “customer set” comfort level. The first step in the evolution of this new system was to define the performance requirements. With this established, the system was then designed, tested and developed in the laboratory and on the road until this desired performance was achieved.

Road simulators like shaker tables are commonly used in the automotive industry for component level dynamic testing. The purpose of a shaker table is to duplicate measured vehicle accelerations in a lab environment. However, there is no universal measure to describe the accuracy of iterated drive files for road simulators. This paper compares frequency domain methods based on discrete Fourier transforms with various time-frequency techniques to develop an accuracy measure which gives more information than metrics which are now common. Results are presented using road data from two typical vehicles and iterated drive files from a six axis shaker table.