Search Results

This work was concerned with use of two-stage cam profile switching to transition between SI and CAI combustion in a multi-cylinder direct fuel injection research engine. In order to achieve robust combustion mode changes, it proved necessary to switch the inlet and exhaust bank of tappets independently of one another. Practical issues addressed to improve tappet response included minimising tappet oil circuit dead volumes and reducing the oil pressure difference before and after a switch. When switching from SI to CAI combustion, it was possible to avoid misfire and operate the engine in a mixed-mode form of combustion. In addition, it was demonstrated that supplementary external EGR could be used to minimise transient peak knocking pressures during such transitions. Differences in overall engine noise levels during SI and CAI have also been qualified and some possible solutions are discussed.

The work was concerned with applying cooled EGR for improved high load fuel economy and reduced pollutant emissions in a turbocharged gasoline engine. While the thermodynamic benefits of EGR were clear, challenges remain to bring the technique to market. A comparison of pre and post compressor EGR supply indicated that post-compressor routing allowed higher compressor efficiencies to be maintained and hence reduced compressor work as the mass flow of EGR was increased. However, with this post-compressor routing, attaining sufficient EGR rate was not possible over the required operating map. Furthermore, at higher engine speeds where the pre-turbine exhaust pressure was greater than the intake plenum pressure, the timing of peak in-cylinder pressure was not as readily advanced towards the optimum.

This work was concerned with increasing the attainable load during gasoline controlled auto-ignition combustion in a multi-cylinder direct fuel injection research engine. To extend the peak output under naturally aspirated conditions it proved favourable to combine internal and external exhaust gas recirculation under stoichiometric fuelled conditions. During turbocharged high load operation it was beneficial in terms of fuel economy to dilute the charge with a combination of internally re-circulated exhaust gases and excess air. Replacing a proportion of these diluents with externally re-circulated burned gases appeared to facilitate lower emissions of HC and CO. The highest load generated via boost was limited by increasing peak in-cylinder pressure and falling gas exchange efficiency. Regardless, the use of boost increased the load at which CAI could be invoked without lean NOx after-treatment.

The work was concerned with the use of exhaust gas recirculation to minimise CO2 and pollutant emissions over a wide operating range in a multi-cylinder research engine. Under part-load conditions a combination of internal and external EGR was used to invoke controlled auto ignition combustion and improve fuel consumption. Outside the CAI regime, small additional fuel savings could be made by employing reduced EGR rates in spark ignition combustion mode. At boosted high load conditions a comparison of excess fuel, excess air and cooled external EGR charge dilution was made. It was apparent that cooled EGR was a more effective suppressant of knock than excess air, with combustion phasing further advanced towards the optimum and improved combustion stability achieved over a wider operating range. The full load emissions reduction potential of EGR was also demonstrated, with emissions of CO2 reduced by up to 17% and engine-out HC and CO decreased by up to 80%.

This work is concerned with the analysis of different charge dilution strategies employed with the intention of inhibiting knock in a high output turbocharged gasoline engine. The dilution approaches considered include excess fuel, excess air and cooled external exhaust gas re-circulation (stoichiometric fuelling). Analysis was performed using a quasi-dimensional combustion model which was implemented in GT-Power as a user-defined routine. This model has been developed to provide a means of correctly predicting trends in engine performance over a range of operating conditions and providing insight into the combustion phenomena controlling these trends. From the modelling and experimental data presented, it would appear that the use of cooled externally re-circulated exhaust gases allowed fuel savings near to those achieved via excess air, but with improved combustion stability and combustion phasing closer to the optimum position.

The work was concerned with experimental study of the turbulent flame development process of ethanol fuels in an optically accessed spark ignition research engine. The fuels were evaluated in a single cylinder engine equipped with full-bore overhead optical access and operated at typical stoichiometric part-load conditions. High-speed natural light (or chemiluminescence) imaging and simultaneous in-cylinder pressure data measurement and analysis were used to understand the fundamental influence of both low and high ethanol content on turbulent flame propagation and subsequent mass burning. Causes for the difference in cyclic variations were evaluated in detail, with comparisons made to existing burning velocity correlations where available.