Search Results

This paper describes vinyl ester based SMC (Sheet molding composite) material for oil sump part in automotive application. This sheet moulding composite is a ready to mould glass-fibre reinforced vinyl ester material primarily used in compression moulding process. This vinyl ester resin is compounded with glass fibre to meet the product functional requirements. Oil sump is a structural component under bonnet that forms the bottommost part of the crankcase and also contain the engine oil before and after it has been circulated through the engine. Generally, metals are preferred material for this application. In this paper, fibre filled vinyl ester based thermoset resin (SMC) material has been explored for oil sump application. They possess excellent properties in terms of tensile strength, modulus, impact strength, dimensional stability, high/low temperature resistance and oil resistance.

Squeak and rattle concerns accounts for approximately 10% of overall vehicle Things Gone Wrong (TGW) and are major quality concern for automotive OEM’s. Objectionable door noises such as squeak and rattle are among the top 10 IQS concerns under any OEM nameplate. Customers perceive Squeak and rattle noises inside a cabin as a major negative indicator of vehicle build quality and durability. Door squeak and rattle issues not only affects customer satisfaction index, but also increase warranty cost to OEM significantly. Especially, issues related to door, irritate customers due to material incompatibilities. Squeaks are friction-induced noises generated by stick-slip phenomenon between interfacing surfaces. Several factors, such as material property, friction coefficient, relative velocity, temperature, and humidity, are involved in squeak noise causes.

Automotive clutches are rotary components which transmits the torque from the engine to the transmission. During the engagement, due to the difference in speed of the shafts the friction lining initially slips until it makes a complete engagement. Enormous amount of heat is generated due to the slippage of the friction lining, leading to poor shift quality and clutch failure. Depending on the road & traffic conditions, and frequency of engagement and disengagement of the clutch, it generates transient heating and cooling cycles. Hill fade test with maximum GVW conditions being the worst case scenario for the clutch. A test was conducted to understand the performance of the clutch, in which clutch burning was observed. The clutch lining got blackened and burning smell was perceived. The friction coefficient drops sharply to a point until it cannot transmit the torque required to encounter the slope. This further worsen clutch slippage and lead to more severe temperature rise.

Due to recent advancements in interior noise level and the excessive use of different grade leathers and plastics in automotive interiors, squeak noise is one of the top customer complaints. Squeak is caused by friction induced vibration due to material incompatibility. To improve costumer perception, interior designs are following zero gap philosophy with little control on tolerances leading to squeak issues. Often manufacturers are left with costly passive treatments like coatings and felts. The best option is to select a compatible material with color and finish; however, this will reduce the design freedom. Material compatibility or stick-slip behavior can be analyzed with a tribology test stand. However, this test is performed on a specimen rather than actual geometry. There were instances, when a material pair was found incompatible when tested on a specimen, but never showed any issue in actual part and vice versa.

The clutch pedal in manual transmission plays a significant role in defining the comfort of driver as it is a direct customer interfaces in the vehicle. Clutch & its hydraulic release system in manual transmission are the significant components which affects the maneuverability of the vehicle and the driver comfort. The clutch pedal characteristics optimization is one of the vital parameters are involving various parameters like pedal effort, pedal travel, hump, engagement and disengagement travel, modulation travel & pedal return curve min load. Normally the clutch pedal characteristics has a hysteresis between the forward and return curve (depress and release of the clutch pedal). The hysteresis is the component of mechanical friction like clutch pedal, clutch cover, and hydraulic seal friction. For an optimum clutch pedal feel, free play, peak effort, max. travel, hump and return load are the major functional parameters.

Proper lubrication is essential for any gear box & axle to get optimized performance. For getting desired life of gear train, we have to maintain minimum oil level inside the gear box or axle, whereas in case of rotating parts such as bearings and shafts, we have to provide sealing such as o rings & oil seals to stop oil coming out from the housing. But, if sealing is not proper seepage & leakage start and reduce the oil level inside the gear box. Oil deficiency leads to scuffing failure in gears and later occurrence of gear & bearing seizure ultimately fails the system. To sustain proper lubrication, we must seal the interfaces appropriately. There are different types of sealing available. Sealing is also depended on application and its location. To protect seal from external environment, we adopt a unique arrangement called slinger which enhances the life of seal.

With increase in demand for quieter product and reduction in masking noise, axle whine management plays a crucial role in the early product development process. Whine is tonal in nature and humans are more sensitive to tonal memory, hence this makes user to experience a very unpleasant ride which in turn results in bad product credibility. Dynamic mesh force excitation is the cause of the axle whine noise. Critical factors in consideration are gear micro geometry variability, misalignments, temperature of operation and resulting bearing pre-load, operating loads, and structural resonances that carry the excitation to the occupant’s ear. The variability associated with gear micro-geometry plays crucial role during optimization in the quest for robust gear design.

Manual transmissions are characterized by gear ratios that are selectable by locking selected gear pairs to the output shaft inside the transmission. Top gear is selected to get a maximum speed and is limited by the engine power, speed and the fuel economy. Lower gears are selected to get maximum speed at maximum gradient. Lower gears are also expected to give creeping speed to avoid usage of clutch and brake in city traffic. Selection of intermediate gears is such that it provides a smoother gear shift. Gear spacing is done in geometric progression. Spacing between the higher gears is usually closer than in the lower gears because drivers shift more often between the lower gears. This is opposed to the conventional idea of progressive spacing where higher gears had more space between them. An objective method is provided for selecting gear ratios for use in vehicle transmission having multiple selectable gears.

Light weighting in modern automotive powertrains call for use of plastics (PP, PA66GF35) for cam covers, intake manifolds and style covers, and noise encapsulation covers. Conventionally, in early stage of design these components are evaluated for static assembly loads & gasket compression loads at component level. However, engine dynamic excitations which are random in nature make it challenging to evaluate these components for required fatigue life. In this paper, robust methodology to evaluate the fatigue life of engine style cover assembly for random vibration excitations is presented. The investigation is carried out in a high power-density 4-cylinder in-line diesel engine. The engine style cover (with Polyurethane foam) is mounted on cam cover and the intake manifold using steel studs and rubber isolators to suppress the radiated noise.

This study introduces a method to examine the flow path of the lubricant inside a transmission housing of a tractor. A typical gearbox has several loads bearing elements which are in relative sliding motion to each other which causes heat to be released. The major sources of friction as well as heat are the meshing teeth between gears (sun/planet, planet/ring & power/range drive gear), thrust washers, thrust bearings and needle roller bearings. The churning of oil performs the vital function of both lubricating these sliding interfaces and cooling these sources of heat, thereby preventing failure of the gearbox. In this paper, we have applied VOF multiphase flow model and sliding meshing to simulate the fluid flow during splashed lubrication within a mating gear box. Lubrication oil dynamics and oil surface interaction with the air is modeled using VOF multiphase approach.

In emerging markets like India, manual transmission vehicles are still most preferred & contributes to 85% of passenger vehicle sales due to its cost benefit. However, customer expects good NVH behavior for comfortable driving experience in the vehicle to maneuver effortlessly in the highly congested traffic conditions in India. Clutch & its hydraulic release system in manual transmission of IC engines are the significant components which affects the NVH behavior & maneuverability of the vehicle and the driver comfort significantly. This paper focuses on the clutch pedal vibration & groan noise concern observed during clutch pedal actuation in high power density SUV vehicle developed for Indian market. The vehicle had highly efficient & light weight engine which has high engine axial vibrations. Axial vibrations are caused due to engine firing impulses & crankshaft bending causes flywheel axial movement.

The clutch pedal in manual transmission plays a significant role in defining the comfort of driver as the component is one of the end user’s direct interface in the vehicle. Whenever driver operates the clutch pedal, comfort and NVH refinement should be felt over the complete pedal travel. The expectations of customer on NVH refinements, such as pedal vibration felt on foot during actuation, becomes the part of perceived quality and hence addressing the concern is very crucial. Due to advancements of technology and down-sizing of engines, NVH becomes the challenging area where the clutch pedal vibrations need to be eliminated to improve the comfort. In this paper we are explaining the problem statement and NVH solution to eliminate the clutch pedal vibration observed during clutch pedal actuation. Pedal vibrations were very severe at 10% clutch pedal pressed condition, and the same tends to diminish till 50% clutch pedal pressed condition.

Vehicles with manual transmission are still the most preferred choice in emerging markets like India due to their benefits in cost, simplicity and fuel economy. However, the ever-increasing vehicle population and traffic congestion demand a smooth clutch operation and a comfortable launch behaviour of any manual transmission vehicle. In the present work, the launch performance of a sports-utility vehicle (SUV) equipped with dual mass flywheel (DMF) and self-adjusting technology (SAT) clutch could be improved significantly by optimizing the clutch system. The vehicle was observed to be having a mild judder during clutch release (with 0% accelerator pedal input) in a normal 1st gear launch in flat road conditions. An extensive experimental measurement at the vehicle level could reveal the launch judder is mainly due to the 1st order excitation forces created by the geometrical inaccuracy of the internal parts of the clutch system.

Nowadays, tractors are frequently used with front-end loaders, dozers and backhoes to cater to various non-agricultural and construction application needs. These applications require frequent shifting of gears due to the constant need for a tractor's forward/reverse direction of motion. Hence, the tractors are fitted with a power shuttle transmission (PST) to cater this need. Power-shuttle transmission (PST) development is a design process that incorporates multiple disciplines such as mechanical, hydraulics, controls and electronics. This paper presents a simulation-based approach to model the power shuttle transmission of the tractor. Firstly, individual components of PST are modelled in detail and then integrated with the complete tractor model. For this, GT-Suite has been used as a simulation platform.

In today’s scenario, internal combustion engines have conflicting requirements of high power density and best in class weight. High power density leads to higher loads on engine components and calls for a material addition to meet the durability targets. Lightweight design not only helps to improve fuel economy but also reduces the overall cost of the engine. Material change from cast iron to aluminium has a huge potential for weight reduction as aluminium has 62% lesser mass density. But this light-weighting impacts the stiffness of the parts as elastic modulus drops by around 50%. Hence, this calls for revisiting the design and usage of optimization tools for load-bearing members on the engine to arrive at optimized sections and ribbing profiles. This paper discusses the optimization approach for one of the engine components i.e., the FEAD (front end accessory drive) bracket.

Rear axles are subjected to bending and torsion loads out of which Bending loads are predominant. In case of Off road vehicles Bi Axial- combination of Bending and torsion loads were predominant, because of axle construction and vehicle usage pattern. Defined test procedures are available for bending durability and torsional durability evaluation of axles. In this experiment, new test methodology was developed for Bi Axial durability evaluation of Off road vehicle rear axle with single servo hydraulic linear actuator. For creating Bi Axial load condition, we may need multiple actuators and complicated fixtures. Axle wheel end is constrained at an angle with suitable fixtures for creating the bending and torsional forces together in the axle. Servo hydraulic linear actuator with suitable loading arm is used for applying the test torque in the axle input flange.

During the vehicle launch (i.e. moving the vehicle from “0” speed), the clutch would be slowly engaged by the Driver or Transmission Control Unit (in Automatic Transmission/Automatic Manual Transmission vehicle) for smooth torque transfer between engine and transmission. The clutch is designed to transfer max engine torque with min heat generation. During the clutch engagement, the difference in flywheel and gearbox input shaft speed is called the clutch slipping phase which then leads to a huge amount of energy being dissipated in terms heat due to friction. As a result, clutch surface temperature increases consistently, when the surface temperature crosses the threshold limit, the clutch wears out quickly or burns spontaneously. Hence it is crucial to predict the energy dissipation and temperature variation in various components of clutch assembly through virtual simulation.

Globally, automotive sector is moving towards improving off-road performance, durability and safety. Need of off-road performance leads to unpredictable overload to powertrain system due to unpaved roads and abuse driving conditions. Generally, shafts and gears in the transmission system are designed to meet infinite life. But, under abuse condition, it undergo overloads in both torsional and bending modes and finally, weak part in the entire system tend to fail first. This paper represents the failure analysis of one such an incident happened in output shaft under abuse test condition. Failure mode was confirmed as torsional overload using Stereo microscope and SEM. Application stress and shear strength of the shaft was calculated and found overstressing was the cause of failure. To avoid recurrence of breakage, improvement options were identified and subjected to static torsional test to quantify the improvement level.

Weight reduction in automotive applications have led to the processing of thermoplastic polymers by foam injection molding. The density of the foamed polymer can be reduced up to 20%. Whilst, work has been reported on the weight reduction of the foamed polymer by using different types of blowing agent technologies, there has been limited studies in the areas of the sound transmission loss and sound attenuation properties of these materials. The present study is intended to understand the effect of chemical blowing agent (CBA) on the properties of polypropylene. The molded specimens were characterized using density, Differential scanning colorimetry (DSC), Thermogravimetric analysis (TGA), Fourier transform infra-red spectroscopy (FT-IR) and sound transmission loss (STL) measurements. Specimens were also tested for tensile properties, flexural properties, Izod impact strength and Heat deflection temperature (HDT) as per standard test protocol.

Fuel efficiency is critical aspect for commercial vehicles as fuel is major part of operational costs. To complicate scenario further, fuel efficiency testing, unlike in passenger cars is more time consuming and laborious. Thus, to save on development cost and save time in actual testing, simulations plays crucial role. Typically, actual vehicle speed and gear usage is captured using reference vehicle in desired route and used it for simulation of target vehicle. Limitation to this approach is captured duty cycle is specific to powertrain and driver behavior of reference vehicle. Any change in powertrain or vehicle resistance or driver of target vehicle will alter duty cycle and hence duty cycle of reference vehicle is no more valid for simulation assessment. This paper demonstrates approach which uses combination of tools to address this challenge. Simulation approach proposed here have three parts.