Search Results

Electric cars are the future of urban mobility which have very less carbon foot print. Unlike the conventional cars which uses BIW (Body in White), some of the electric cars are made with a space frame architecture, which is light weight and suitable for low volume production. In this architecture, underbody consists of frames, battery pack, electronics housing and electric motor. Underbody drag increases due to air entrapment around these components. Aerodynamic study for baseline model using CFD simulations showed that there was a considerable air resistance due to underbody components. To reduce the underbody drag, different add-ons are used and their effect on drag is studied. A front spoiler (air dam) is used to deflect the incoming air towards sides of the car. A under hood cover for front components, trailing arm cover for trailing arm and rear bumper cover for rear components were used to reduce underbody drag.

Whole Body Vibration (WBV) of tractors was measured on different surfaces in real world usage pattern of Indian customers on tractors of various capacities. Vibration levels were measured at the interface of the seat and the operator, on the seat base/floor and on the head. The mean weighted Root Mean Square (RMS) values along the different axes, the vector sum of weighted RMS values along the three orthogonal axes, the crest factor, Vibration Dose Value (VDV) and 8 h exposure levels were calculated according to ISO 2631-1. In addition to the above parameters, the transmissibility between the seat base and the seat interface (SEAT) and between the seat interface and the operator head (TR) were also calculated. Finally, these parameters were correlated with the subjective feel of customers which was captured through suitable questionnaires. It is observed that the Indian tractor operators are exposed to WBV that exceeds the cautionary boundaries set in place by the ISO 2631-1.

In the current era, vehicle manufacturers focus has increased towards passenger comfort and one of the key areas is NVH. Vehicle level NVH targets are cascaded to component level for obtaining better refinement in cabin. One such performance attribute is sloshing noise of urea in diesel vehicles. Migration from BS4 to BS6.2 norms demand complex technological changes to automobile manufacturers to add extra components to the vehicles which is a big challenge in identifying the locations at critical stage of the project phase. In one of the developments of mid SUV category vehicle, sloshing noise from urea tank is perceived as objectionable during low-speed braking and while passing over speed breakers. This paper addresses the measurement conditions of sloshing noise and its evaluation procedure to quantify the sloshing noise at vehicle level. The sloshing noise is perceived in the frequency band of 50 to 1000 Hz.

The purpose of this study is to conduct dynamic seat pressure mapping on vehicle seats during its operation on different test tracks under ambient environmental conditions for a defined speed. The test track comprises of pave roads, high frequency track, low frequency track and twist track. The variations in pressure distribution on seat during diverse road load inputs help to understand the seat cushion and back comfort for unique percentiles of human subjects ranging from 50th to 95th percentile population. For conducting the study, a sport utility vehicle (SUV) loaded with leatherette seats has chosen. Totally six participants (human subjects), five male and one female selected for the study based on their BMI (Body mass index) and body morphology. Pressure mats suitable for taking dynamic load inputs and able to log the data at a defined sampling rate mounted on seats and secured properly. The pressure mats should cover the seat cushion, bolster areas and back seat completely.

In today's competitive automobile market, customers have become more sensitive towards NVH behavior of the vehicle than ever. The noise generated by gear rattle is one of the main contributors towards customer's overall NVH perception. This paper adopts a model based design approach towards gear rattle phenomenon to predict the tendency of gear rattle at a very early stage of design. This up-front understanding of gear rattle will potentially reduce the expensive design changes and iterations at later stages. A single unloaded gear pair is modeled in AMESim software, which is then extended to the complete gearbox in neutral condition. The sensitivity of rattle index for different input parameters is studied. Analysis on uncertainty propagation is carried out to find the rattle index distribution for Gaussian variation of input parameters. A novel rattle index based on Jerk is proposed and compared with the existing index.

Sound package material selection plays a vital role in maintaining passenger comfort by suppressing noise inside cabin. Sound package development in static condition minimizes the extrinsic variables which influence the measurements. The consideration of static condition favors simulation and its correlation with test data. Once correlation is achieved, simulation inputs are used for further optimization and improvements. Noise control can be done in three levels by working either on source, path or receiver. In automobiles, there are many sources of noise such as engine, tire and wind. This topic deals with quantification of various transfer paths between source and receiver location using Power Based Noise Reduction (PBNR) method. This methodology is used in both simulation and testing along with its overall scope for improvement. It is best to quantify path strength in terms of energy levels instead of mere amplitude due to its independency on external test conditions.

Synchronizer is the key element for the smoother gear shift operation in the constant mesh transmission. In the gear shift operation, the double bump occurs at the contact between the sleeve teeth and the clutch body ring teeth after the full synchronization. The double bump is random in nature and the dynamics is difficult to predict. The double bump gives a reaction force to the driver and affects the gear shift quality. This paper focus on the sensitivity analysis of the synchronizer ring index percentage and the clutch body ring asymmetric chamfer angle to reduce the occurrence and magnitude of the double bump. The system level simulation model is developed using 1D simulation tool. The modeling is done after complete declutching event so that there is no power supply to the transmission. The model can handle both upstream and downstream reflected inertia depending upon the gear shift event.

BSR (Buzz, Squeak and Rattle) is one of the oldest concerns in automobiles which directly reflect the build, assembly and manufacturing quality of a vehicle. In a cabin all the areas where there is relative motion between two components, such as trims, instrument panel and seats, are prone to squeak. This paper explains the study of seat squeak measurement and diagnosis which is a major concern for one of the products which is already in the market. Since squeak is a friction induced non stationary phenomenon, lot of effort was required to generate squeak in both component as well as vehicle level. At component level, electrodynamic shaker was extensively used for generation of squeak signals. In Vehicle level, driving through different road patterns, pave track and forced excitation on four posters are performed for generation of squeak signals. In this paper usage of wavelet and Zwikker loudness are explained for the diagnosis of seat squeak to identify the problematic frequencies.

Heat exchangers are thermoregulatory system of an automotive air conditioning system. They are responsible for heat exchange between refrigerant and air. Sizing of the heat exchanger becomes critical to achieve the required thermal performance. In the present work, the behavior of heat exchanger with respect to change in size is studied in detail by developing a scaling model. The limited experiments have been conducted for 3 different condensers. Commercially available 1D tool GT Suite is used for simulations. The heat exchangers are modeled using COOL3D module of GT Suite. The experimental thermal capacities of heat exchanger are compared with the simulated values. A good agreement up to ±2.3% is found between the experiments and simulations. Then developed scaling model in GT Suite is used for predicting the thermal behavior of heat exchangers by changing the size of the heat exchanger. Scaled thermal capacities of each model is compared with the corresponding experimental results.

Airbags play a vital role in occupant protection during a crash event. Apart from the crash test the airbags have to additionally meet the requirements of the ECE R 12 headform impact test with Driver's Airbag (DAB) located in the steering wheel being deployed and the ECE R21 headform impact test for Passenger Airbag (PAB) in undeployed condition. Improper location of the PAB module below the Instrument Panel, the design of the air bag housing and the Instrument Panel are some of the factors that could lead to non compliance of the components of the uninflated PAB. The paper deals with the investigation conducted for compliance of the PAB to ECE R 21 with the uninflated air bag in meeting the requirements of 80 g at 19.3 km/h by proper location, changes to the design of the PAB cover, air bag housing brackets, etc.

Closed crankcase ventilation prevent harmful gases from entering atmosphere thereby reducing hydrocarbon emissions. Ventilation system usually carries blowby gases along with oil mist generated from Engine to Air intake system. Major sources of blowby occurs from leak in combustion chamber through piston rings, leakage from turbocharger shafts & leakage from valve guides. Oil mist carried by these blowby gases gets separated using separation media before passing to Air Intake. Fleece separation media has high separation efficiency with lower pressure loss for oil aerosol particles having size above 10 microns. However, efficiency of fleece media drops drastically if size of aerosol particles are below 10 microns. Aerosol mist of lower particle size (>10 microns) generally forms due to flash boiling on piston under crown area and from shafts of turbo charger due to high speeds combined with elevated temperatures. High power density diesel engine is taken for our study.

Globally all OEMs are moving towards electric vehicle to reduce emission and fuel cost. Customers expect highest level of refinement and sophistication in electric vehicle. At present, the customers are sensitive to high pitched tonal noise produced by electric powertrain which gives a lot of challenges to NVH engineers to arrive at a cost-effective solution in less span of time. Higher structure borne tonal noise is perceived in electric vehicle at the vehicle speeds of ~ 28 kmph, 45 kmph and 85 kmph. The test vehicle is front wheel drive compact SUV powered by motor in the front. The electric drive unit is connected to cradle and subframe with help of three mounts. Transfer path analysis (TPA) using blocked forces method is carried out to identify the exact forces of the electric drive unit entering the mounts. Powertrain mount is characterized by applying the predicted forces and dynamic stiffness at problematic frequency is measured.

In automotive market, with competitive car prices, build quality of a car will be a major distinguishing factor. Consumer's need for acoustic comfort has evolved from the removal of annoying noises to perceived sound quality. Operational sounds from electromechanical systems like sunroof system, window regulator, door lock system, HVAC etc. directly interact with users’ senses. The perceived acoustics comfort of these sounds are direct indicators of vehicle character and can influence customer’s buying decision. With the reduction in product development time and stringent cost constraints, a proper structured target setting methodology to benchmark & evaluate these operational sounds is crucial. In this paper, such a target setting methodology is proposed and discussed for operational sound quality evaluation. Electromechanical noises from various vehicles are measured using binaural head measurement system.

The prime focus of automotive industries in recent times is to improve the energy efficiency of automotive subsystem and system as whole. Harvesting the waste energy and averaging the peak thermal loads using thermal energy storage (TES) materials and devices can help to improve the energy efficiency of automotive system and sub-system. The phase change materials (PCM) well suit the requirement of energy storage/release according to demand requirement. One such example of TES using PCM is extended automotive cabin comfort during vehicle idling and city traffics including start/stop of the engine at traffic stops. PCM as TES poses high density and capacity in thermal energy storage and release. It is due to latent heat absorption and release during phase change. Generally the latent heat of a material compare to it sensible heat is much higher, almost an order of 2. For example, latent heat of ice is almost 160 times higher than sensible heat for a kelvin temperature rise of ice.

Hybrid Electric Vehicles (HEVs), Plug-in Hybrid Electric Vehicles (PHEVs), Extended Range Electric Vehicles (EREVs), Battery Electric Vehicles' (BEVs) development is gaining traction across all geographies to help meet ever increasing fuel economy regulations and as a pathway to offset concerns due to climate change and improve the overall green quotient of automobiles. These technologies have primarily shifted towards Li-ion batteries for Energy Storage (due to energy density and mass). In order to make actual business sense of these technologies, of which, battery is a major cost driver, it is necessary for these batteries to provide similar performance and life expectancy across the operating and soak (storage) range of the vehicles, as well as provide the requirements at a competitive cost.

The 48V mild-Hybrid system uses a 48V Lithium - Ion battery pack to boost the engine performance, to harness recuperative energy and to supply the accessory boardnet power requirement. Thermal management of the 48V battery pack is critical for its optimal utilization to realize the mild hybrid functionality, to meet CO2 reduction targets and useful life particularly under usage in hot ambient conditions. This paper discusses the various challenges and options of thermal management for the 48V battery pack based on the usage pattern and environmental conditions. The lifetime for a passively cooled battery pack is estimated for a typical Indian usage pattern. Active-air cooling is evaluated for the thermal management of the 48V mild-Hybrid battery pack. The tradeoffs are compared in terms of availability of hybrid functions and battery life.

This study presents a method for a cool down simulation of passenger compartments. The purpose was to integrate the 3D Computational Fluid Dynamics (CFD) software StarCCM+ with the 1D thermal management software KULI. The targets were to achieve accurate prediction of temperature diffusion inside the cabin for a transient cycle simultaneously reducing the modelling effort and CPU-time consumption. The 1D simulation model was developed in KULI and the flow field data required to simulate mass flow and diffusion inside the cabin was implemented from Star CCM+. The simulation model consists of a multi-zone cabin and models the complete refrigerant circuit consisting of evaporator, condenser, Thermal Expansion Valve (TXV) and compressor. This paper describes the process flow, definition of the inputs required and finally the validation of the simulation data with experiments.

Regulations on pedestrian safety have been introduced globally since the year 1990 and in India it will have to be met around the year 2016. Process of making vehicle compliant to this regulation requires rigorous design development and testing. Testing involves propelling head-forms (Child and Adult) on bonnet at 35 km/h and 40 km/h and leg-forms (Upper and Lower) on bumper at 40 km/h according to the different National / International / NCAP regulatory requirements A pedestrian protection test rig has been indigenously designed and developed in-house to perform pedestrian protection impact testing in-house. The paper describes the salient features of the pedestrian protection test rig, its functioning, operation and process of acquiring the data for determination of the values required by crash safety regulations.

In-vehicle displays such as an instrument cluster in a vehicle provide vital information to the user. The information in terms of displays and tell-tales needs to be perceived by the user with minimal glance during driving. Drivers must recognize the condition of the vehicle and the state of its surroundings through primarily visual means. Drivers then process this in the brain, draw on their memory to identify problem situations, decide on a plan of action and execute it in order to avoid an accident. There are visual hindrances seen in real world scenario such as obscuration, reflection and glare on the instrument cluster which prevents the vital information flow from vehicle to the driver. In order to ensure safety while driving, the instrument cluster or driver displays should be placed in an optimized location. This paper deals with how to achieve a visual hindrance free cluster position in a vehicle to protect the important information flow from the vehicle to the driver.

Light weight and Robust manufacturing technologies are always needed for transformation drive in the Automotive industry for the next-generation vehicles with greater Power to weight ratio. Innovations and process developments in materials and manufacturing processes are key to this light weighting transformation. Aluminium material has been widely used for these light weighting opportunities. However, aluminum joining techniques, characterized by their poor quality and consistency are limiting this transformation. This technical paper represents one of such case, where the part is made up of Aluminium through conventional casting route which has affected the laser weld quality due to poor casting soundness. This experiment explains in detail about the importance of Casting soundness for laser weld quality, weld penetration, strength etc., and the Product consistency.