Search Results

Gearbox power transfer efficiency is a major factor in overall powertrain efficiency of a passenger vehicle. With rapidly changing emission and fuel efficiency regulations, there is a push to increase the gearbox efficiency to improve the overall fuel economy of the vehicle. In case of an existing gearbox, efficiency can be improved by using the low viscosity lubrication oil. Despite a benefit in increasing the gearbox efficiency, lowering down the viscosity of lubrication oil gives rise to few challenges with respect to its performance. One of these challenges is breather performance which defines that transmission oil should not come out of breather pipe in some pre-defined conditions during gearbox operation. As this validation is being carried out on proto parts when the complete system is ready, failure to satisfy the defined criteria for breather performance can lead to multiple trials.

Valve train system is one major contributor to engine overall friction loss and is approximately 30% of total engine friction at lower speed and approximately 20 % at higher engine speed. Valve spring loads (preload and working) are proportional to friction loss of valve train. To optimizing the valve spring design main requirement is valve train perform it function safely at maximum engine cutoff RPM with minimum preload and working load. Robustness and frictional power loss are contradicting requirement, robustness demand high stiffness spring for better valve jump and bounce performance with dynamic safe valve spring design, on the other hand low frictional power loss demand for use of low stiffness spring. To optimize the valve spring stiffness for meeting both the requirement we need accurate prediction of valve spring in design stage and good correlation with testing data to reduce the number of iterations.

With more stringent emission norm coming in future, add more pressure on IC engine to improve fuel efficiency for survival in next few decades. In gasoline SI (spark ignition) engine, valve events have major influence on fuel economy, performance and exhaust emissions. Optimization of valve event demands for extensive simulation and testing to achieve balance between conflicting requirement of low end torque, maximum power output, part load fuel consumption and emission performance. Balance between these requirements will become more critical when designing low cost valve train without VVT (Variable valve timing) to reduce overall cost of engine. Higher CR (Compression ratio) is an important low cost measure to achieve higher thermal efficiency but creates issue of knocking thereby limiting low speed high load performance. The effective CR reduction by means of late intake valve closing (LIVC) is one way to achieve higher expansion ratio while keeping high geometric CR.

Shielding vehicle underbody or engine room components from exhaust heat is becoming a difficult task with increasing packaging constraints, which lead to the proximity of components with high temperatures of the exhaust systems. Heat insulators are provided to protect various components from exhaust system parts. Generally the requirement of heat insulators are fixed on the basis of benchmarked temperatures measured on vehicles with similar layout, during the initial phase of vehicle design. Also various CFD techniques are available to predict the surface temperatures on components in order to determine the necessity of a heat insulator. The aforementioned techniques use radiation and convection heat transfer effects on a complete vehicle model and the overall process generally takes considerable time to provide the results. This paper deals with a theoretical approach to predict the temperatures on nearby components due to exhaust system heat.

Exhaust system of an automobile is primarily employed in automobile to purify exhaust gases and reduce noise due to combustion. However, a side-effect of the above function is the increase in backpressure. As specified in various literatures, an increase in backpressure can lead to a deterioration on engine performance (Power & torque). Benefit of backpressure reduction can be further taken in terms improving the power & torque of engine or improving the fuel economy. With growing concerns related to global warming and CO2 emissions, reducing exhaust back pressure is one of the promising areas in engine design in order to improve the fuel economy of the automobile and achieving carbon neutrality targets. However, reducing the back pressure generally tends to deteriorate the noise attenuation performance of the Exhaust system.

Hardened steel is the majorly used raw material for automotive components. In spite of its abundance, its application is limited due to low fatigue life in dynamic loading. Shot peening is one of the identified processes to improve the fatigue life of the ductile steel by inducing the work hardening & surface improvement. The process of shot peening involves the bombardment of shots on the component surface. As the process & technique, the shot size selection plays very important role in the fatigue life improvement as it alters the results substantially. Also during the process, shot size decreases due to the normal wear of the shots after hitting the component surface. As a result, there is always a ratio of various sizes of the shots involved in the process. Therefore it becomes imperative to control the shot size ratio for obtaining the required work hardening & possible fatigue life improvement.

Gear noise and vibration in automobile transmissions is a phenomenon of great concern. Noise generated at the gearbox, due to gear meshing, also known as gear whine, gets transferred from the engine cabin to the passenger cabin via various transfer paths and is perceived as air borne noise to the passengers in the vehicle. This noise due to its tonal nature can be very uncomfortable to the passengers. Optimizing micro-geometry of a gear pair can help in improving the stress distribution on tooth flank and reducing the sound level of the tonal noise generated during the running of the gearbox when that gear pair is engaged. This technical paper contains the study of variation in noise level in passenger cabin and contact on tooth flank with change in micro-geometry parameters (involute slope and lead slope) of a particular gear pair. Further scope of study has been discussed at the end of the paper.

Interior sound quality is one of the significant factors contributing to the comfort level of the occupants of a passenger car. One of the major reasons for the deterioration of interior sound quality is the booming noise. Booming noise is a low frequency (20Hz∼300Hz) structure borne noise which occurs mainly due to the powertrain excitations or road excitations. Several methods have been developed over time to identify and troubleshoot the causes of booming noise [1]. In this paper an attempt has been made to understand the booming noise by analyzing structural (panels) and acoustic (cavity) modes. Both the structural modes and the acoustic modes of the vehicle cabin were measured experimentally on a B-segment hatchback vehicle using a novel approach and the coupled modes were identified.

Fabrics play a vital role in defining the overall aesthetics of automotive interiors, primarily with fabric cleanliness. In this respect, the cleanliness of the fabric also becomes equally important. The fabric interior in a car is very prone to staining due to the spilling of water or any liquid substance over it. In order to protect and enhance the life of the fabric, various chemical treatments are suggested as fabric finishes. There are different chemical bases available for the same. Fluorocarbon base is the most effective treatment and is the focus of this study. This chemical treatment lowers the surface energy of the fabric by increasing the hydrophobicity of fabric. Hence, the liquid roll over the surface in the form of droplets by creating higher contact angle over the fiber surface. This study focuses on the effect of chemical treatment on the automotive fabric’s parameters, especially light color fabric.

Nowadays, Road Load Simulators are used by automobile companies to reproduce the accurate and multi axial stresses in test parts to simulate the real loading conditions. The road conditions are simulated in lab by measuring the customer usage data by sensors like Wheel Force transducers, accelerometers, displacement sensors and strain gauges on the vehicle body and suspension parts. The acquired data is simulated in lab condition by generating ‘drive file’ using the response of the above mentioned sensors [2]. For generation of proper drive file, not only good FRF but ensuring stability of inverse FRF is also essential. Stability of the inverse FRF depends upon the simulation channels used. In this paper experimental approach has been applied for the optimization of the simulation channels to be used for simulation of normal Indian passenger car on 4 corners, 6-Axis Road Load Simulator. Time domain tests were performed to identify potential simulation channels.

The biggest challenge in vehicle BIW design today is to make a light, cost effective and energy absorbing structure. With the increasing competition as well as increasing customer awareness, today’s vehicle has to satisfy several aesthetic and functional requirements besides the mandatory regulatory requirements. While working on global platform, it is challenging to comply with both pedestrian protection and low speed bumper impact (ECE-R42) and at the same time meeting the styling intent of reducing the front overhang. Pedestrian lower leg compliance demands space between bumper member and bumper, a condition that reduces the space available for energy absorption during low speed impact (ECE-R42). Therefore, reduction in front overhang poses a problem in meeting both the requirements with limited space. This paper outlines vehicle case study in order to optimize the design of Bumper Beam structure, for complying with regulatory requirements while satisfying the styling intent.

With the advent of stricter regulation for tail pipe emission and urge to reduce the carbon foot prints, the engine hardware has undergone through evolutionary changes over the years i.e., boosting, low viscosity engine oil, high pressure fuel injection, cooled EGR, friction reduction, downsizing etc. These technological changes have led to the challenge of increase in radiated noise level from the engine (source) due to increased number of auxiliary drives on engine i.e., Turbo charger, HP fuel pump along with faster combustion & harsher operating conditions. The fuel system is one such system which has become most intricate with operating pressure going above 2000bar in the fuel rail and capability of up to 10 fuel injection per combustion. These changes in hardware could result in abnormal noise generation during specific operating conditions which may result in customer annoyance inside vehicle cabin.

Automobile components are usually subjected to complex varying loads. Thus, fatigue failure is a common mode of failure in automobile components. Accurately predicting the fatigue life is the key point for light weight and also reliability design of automobile components. Various life prediction theories are being used in the automotive industry for damage analysis using material S-N curves. However, due to variability in manufacturing, material spec etc. it is difficult to predict the experimental lives using conventional theories. Probability based statistical modeling is prevalent in the industry for life prediction. Probabilistic plots of cycles to failure to constant amplitude loads are plotted and used for prediction purpose. As the component is subjected to varying loads in real world, defining a single parameter i.e. damage would be more relevant compared to loads.

In recent years, worldwide automotive manufacturers have been continuously working in the research of suitable technical solutions to meet upcoming stringent Real Driving Emission (RDE) and Corporate Average Fuel Economy (CAFÉ) targets, as set by international regulatory authorities. Many technologies have been already developed, or are currently under study by automotive manufacturer for gasoline engines, to meet legislated targets. In-line with the above objective, there are many technologies available in the market to expand lambda 1 (λ=1) region by reducing fuel enrichment at high load-high revolutions per minute (RPM) by reducing exhaust gas temperature (for catalyst protection) for RDE regulation [1]. Integrated Exhaust Manifold (IEM) is the key technology for the Internal Combustion (IC) for the subjected matter as catalyst durability protection is done by reducing exhaust gas temperatures instead of injecting excess fuel for cooling catalyst.

Automotive floor carpet serves the purpose of insulating airborne noises like road-tire noise, transmission noise, fuel pump noise etc. Most commonly used automotive floor carpet structure is- molded sound barrier (PE, vinyl etc.) decoupled from the floor pan with an absorber such as felt. With increasing customer expectations and fuel efficiency requirements, the NVH requirements are increasing as well. The only possible way of increasing acoustic performance (Specifically, Sound Transmission Loss, STL) in the mentioned carpet structure is to increase the barrier material. This solution, however, comes at a great weight penalty. Theoretically, increasing the number of decoupled barrier layers greatly enhances the STL performance of an acoustic packaging for same weight. In practice, however, this solution presents problems like- ineffectiveness at lower frequencies, sudden dip in performance at modal frequencies.

Vehicle cabin comfort emphasizes a specific image of a brand and its product quality. Low frequency powertrain induced noise and vibration levels are a major contributor affecting comfort inside passenger cabin. Thus, using hydraulic mount is a natural choice. Introduction of lighter body panels coupled with cost effective hydraulic mounts has resulted in some additional noises on rough road surfaces which are challenging to identify during design phase. This paper presents a novel approach to identify two such noises i.e. Cavitation noise and Mount membrane hitting noise based on component level testing which are validated at vehicle experimentally. These noises are encountered at 20~30kmph on undulated road surfaces. Sound quality aspect of such noises is also studied to evaluate the solution effectiveness.

In order to meet the challenges of future CAFE regulations & pollutant emission, vehicle fuel efficiency must be improved upon without compromising vehicle performance. Optimization of engine breathing & its impact on vehicle level fuel economy, performance needs balance between conflicting requirements of vehicle Fuel Economy, performance & drivability. In this study a Port Fuel Injection, naturally aspirated small passenger car gasoline engine was selected which was being used in a typical small passenger car. Simulation approach was used to investigate vehicle fuel economy and performance, where-in 1D CFD Engine model was used to investigate and optimize Valve train events (Intake and exhaust valve open and close timings) for best fuel economy. Engine Simulation software is physics based and uses a phenomenological approach 0-D turbulent combustion model to calculate engine performance parameters. Engine simulation model was calibrated within 95% accuracy of test data.

Due to intense peak summer temperatures and sunny summers in tropical countries like India etc., achieving the required thermal comfort of car occupants without compromising on fuel efficiency is becoming increasingly challenging. The major source of heat load on vehicle is Solar Load. Therefore, a study has been conducted to evaluate the heat load on vehicle cabin due to solar radiations and its impact on vehicle air-conditioning system performance with various combinations of door glasses and windscreen. The glasses used for this study are classified as green, dark green, dark gray, standard PVB (Polyvinyl Butyral) windscreen and PVB windscreen having infrared cut particles. For each glass, part level evaluation was done to find out the percentage transmittance of light of different wavelengths and heat flux through each glass.

Automobile industry is shifting its focus from conventional fuel vehicles to NexGen vehicles. The NexGen vehicles have electrical components to propel the vehicle apart from mechanical system. These vehicles have a goal of achieving better fuel efficiency along with reduced emissions making it customer as well as environment friendly. Idle start-stop is a key feature of NexGen vehicles, where, the Engine ECU switches to engine stop mode while idling to cut the fuel consumption and increase fuel efficiency. Engine restarts when there is an input from driver to run the vehicle. There is always a clash between the Engine ECU and automatic climate control unit (Auto-AC) either to enter idle stop mode for better fuel efficiency or inhibit idle stop mode to keep the compressor running for driver comfort. This clash can be resolved in two ways: 1 Hardware change and, 2 Software change Hardware change leads to increase in cost, validation effort and time.

Over the years, Fuel efficiency and cabin comfort of vehicle has become increasingly important in buying decision and can significantly give competitive edge to the vehicle in marketplace. Weight and friction reduction of rotating and reciprocating components in engines is one of the proven approaches to improve the efficiency of internal combustion engine. To reduce the friction, the general approach is to use low viscosity engine oils, improve the surface finish and reduce the contact area of sliding elements, switch over from sliding contact to rolling contact etc. However sometimes this approach has adverse impact on engine NVH characteristics due to occurrence of abnormal transient noise due to mechanical knocking of the components in specific operating conditions.