Search Results

As vehicle emissions regulations become increasingly stringent, there is a growing need to accurately model aftertreatment systems to aid in the development of ultra-low NOx vehicles. Common solutions to this problem include the development of complex chemical models or expansive neural networks. This paper aims to present the development process of a simpler Selective Catalytic Reduction (SCR) conversion efficiency Simulink model for the purposes of modeling tail pipe NOx emission levels based on various inputs, temperature shifts and SCR locations, arrangements and/or sizes in the system. The main objective is to utilize this model to predict tail pipe NOx emissions of the EPA Federal Test Procedures for heavy-duty vehicles. The model presented within is focused exclusively on heavy-duty application compression ignition engines and their corresponding aftertreatment setups.

In order to validate the operation of advanced driver assistance systems (ADAS), tests must be performed that assess the performance of the system in response to different scenarios. Some of these systems are designed for crash-imminent situations, and safely testing them requires large stretches of controlled pavement, expensive surrogate targets, and a fully functional vehicle. As a possible more-manageable alternative to testing the full vehicle in these situations, this study sought to explore whether these systems could be isolated, and tests could be performed on a bench via a hardware-in-the-loop methodology. For camera systems, these benches are called Camera-in-the-Loop (CiL) systems and involve presenting visual stimuli to the device via an external input.

The Federal Side Impact Test Procedure prescribed by FMVSS 214, simulates a central, orthogonal intersection collision between two moving vehicles by impacting the side of the stationary test vehicle with a moving test buck in a crabbed configuration. While the pre- and post-impact speeds of the vehicles involved in an accident can not be duplicated using this method, closing speeds, vehicle damage, vehicle speed changes and vehicle accelerations can be duplicated. These are the important parameters for the examination of vehicle restraint system performance and the prediction of occupant injury. The acceptability of this method of testing is not as obvious for the reconstruction of accidents where the impact is non-central, or the angle of impact is not orthogonal. This paper will examine the use of crash testing with a single moving vehicle to simulate oblique or non-central collisions between two moving vehicles.

The objective is to determine whether responses and injury risks for pediatric occupants in child restraint systems (CRS) are affected by vehicle seat cushion stiffness and fore/aft cushion length. Eighteen sled tests were conducted using the Federal Motor Vehicles Safety Standard (FMVSS) 213 frontal pulse (48 km/h). Seats from a recent model year vehicle were customized by the manufacturer with three different levels of cushion stiffness: compliant, mid-range, and stiff. Each stiffness level was quantified using ASTM D 3574-08 and all were within the realistic range of modern production seats. The usable length of each seat cushion was manipulated using foam spacers provided by the manufacturer. Two different seat lengths were examined: short (34.0 cm) and long (43.5 cm).

In this paper, a series of design, development, and implementation details for testing and evaluation of Lane Departure Warning and Prevention systems are being discussed. The approach taken to generate a set of repeatable and relevant test scenarios and to formulate the test procedures to ensure the fidelity of the collected data includes initial statistical analysis of applicable statistics; growth and probabilistic pruning of a test matrix; simulation studies to support procedure design; and vehicle instrumentation for data collection. The success of this comprehensive approach strongly suggests that the steps illustrated in this paper can serve as guidelines towards a more general class of vehicular safety and advanced driver assistance systems evaluation.

Current Advanced Driver Assistance Systems (ADAS) often interact with the driver; aiding with either warnings or direct intervention. This work explores the development of an ADAS system to provide lane departure warning, forward collision warning, and a recommended following distance for a custom plug-in hybrid-electric vehicle. The system utilizes off-the-shelf hardware with in-house computer vision and sensor fusion algorithms to create a low-cost SAE Level 0 driver assistance system. The system utilizes a radar sensor as well as a camera to detect, classify, and track target vehicles. This work will illustrate the systems engineering methods used for outlining customer requirements, technical requirements, component selection, software development, simulation, vehicle fitment, and validation. Similar system engineering processes could be implemented for higher level SAE systems.

Multiple clutches are engaged to achieve a specific gear ratio in an automatic transmission (AT). When an engaged clutch loses pressure during the AT operation, it is classified as a clutch stuck off fault. Automatic transmissions can enter in neutral states because of these faults and the vehicle can lose power at the wheels. Our previous work describes a systematic way of performing sensor placement analysis for diagnosis of clutch faults in automatic transmissions. In this paper, we approach the issue from the point of view similar to that of functional safety according to the ISO 26262 standard; where a transmission functional safety concept should address transitioning to a safe state in case of hazards associated with stuck off clutches.

This study examines the performance of rear-facing child restraint systems (RF CRS) in moderate severity rear impact sled tests. The study also investigates the effects of RF CRS features on CRS kinematics and anthropomorphic test device (ATD) injury metrics in this scenario. Twelve tests were conducted at a moderate severity rear impact sled pulse (approximately 28.2 km/h and 18.4 g). Four models of RF CRS were tested in the rear outboard positions of a sedan seat. The CRABI 12-month-old and Hybrid III 3-year-old ATDs were instrumented with head and chest accelerometers, head angular rate sensors, six-axis upper neck load cells, and a chest linear potentiometer (3-year-old only). The effects of carry handle position, occupant size, presence of anti-rebound bar, Swedish style tethering, and lower anchor vs. seat belt installation were investigated. Data were also compared to pediatric injury assessment reference values (IARV).

Testing vision-based advanced driver assistance systems (ADAS) in a Camera-in-the-Loop (CiL) bench setup, where external visual inputs are used to stimulate the system, provides an opportunity to experiment with a wide variety of test scenarios, different types of vehicle actors, vulnerable road users, and weather conditions that may be difficult to replicate in the real world. In addition, once the CiL bench is setup and operating, experiments can be performed in less time when compared to track testing alternatives. In order to better quantify normal operating zones, track testing results were used to identify behavior corridors via a statistical methodology. After determining normal operational variability via track testing of baseline stationary surrogate vehicle and pedestrian scenarios, these operating zones were applied to screen-based testing in a CiL test setup to determine particularly challenging scenarios which might benefit from replication in a track testing environment.

Low speed autonomous shuttles emulating SAE Level L4 automated driving using human driver assisted autonomy have been operating in geo-fenced areas in several cities in the US and the rest of the world. These autonomous vehicles (AV) are operated by small to mid-sized technology companies that do not have the resources of automotive OEMs for carrying out exhaustive, comprehensive testing of their AV technology solutions before public road deployment. Due to the low speed of operation and hence not operating on roads containing highways, the base vehicles of these AV shuttles are not required to go through rigorous certification tests. The way these vehicles’ driver assisted AV technology is tested and allowed for public road deployment is continuously evolving but is not standardized and shows differences between the different states where these vehicles operate.

Forensic injury accident reconstruction is used to determine what happened in an accident, typically for use in a court of law. In order to be admitted as evidence in a trial, the analysis must be scientifically sound, and performed utilizing standard scientific methods. The use of motion capture methods for forensic biomechanical applications provides an accurate, scientifically proven technique that has advantages not only due to its technical capabilities, but also in its highly visual manner of result presentation. This paper illustrates the use of a near-infrared motion capture system in two different types of forensic biomechanics applications. In one case, motion capture was utilized to capture externally applied force data and synchronized with the three-dimensional human body posture to perform a musculoskeletal biomechanics analysis.

Connectivity in ground vehicles allows vehicles to share crucial vehicle data, such as vehicle acceleration and speed, with each other. Using sensors such as radars and lidars, on the other hand, the intravehicular distance between a leader vehicle and a host vehicle can be detected. Cooperative Adaptive Cruise Control (CACC) builds upon ground vehicle connectivity and sensor information to form convoys with automated car following. CACC can also be used to improve fuel economy and mobility performance of vehicles in the said convoy. In this paper, a CACC system is presented, where the acceleration of the lead vehicle is used in the calculation of desired vehicle speed. In addition to the smooth car following abilities, the proposed CACC also has the capability to calculate a speed profile for the ego vehicle that is fuel efficient, making it an Ecological CACC (Eco-CACC) model.

A significant number of formed parts constitute the components of an automobile or aircraft. The formed blanks for the components are produced at different temperatures ranging from room temperature to 2250 degrees Fahrenheit for steel. Forming progressions convert a basic shape or geometry (a cylindrical billet, for example) of metal into a more complex shape close to the required final component geometry. The progression steps, choice of temperatures and equipment significantly impact the cost of the blank. A ‘Discriminating Cost Model’ was developed to capture the cost effectiveness of a given choice of process or equipment, and an AI (Artificial Intelligence) search algorithm implemented to quickly search through the large number of process and equipment selection options to arrive at the most cost effective choice. Two applications of this methodology to existing plant processes to significantly reduce cost and implement ‘lean’ principles of manufacturing are discussed.

A machine has been developed to measure the complete inertia matrix; mass, center of gravity (CG) location, and all moments and products of inertia. Among other things these quantities are useful in studying engine vibrations, calculation of the torque roll axis, and in the placement of engine mounts. While the machine was developed primarily for engines it can be used for other objects of similar size and weight, and even smaller objects such as tires and wheels/rims. A key feature of the device is that the object, once placed on the test table, is never reoriented during the test cycle. This reduces the testing time to an hour or less, with the setup time being a few minutes to a few hours depending on the complexity of the shape of the object. Other inertia test methods can require up to five reorientations, separate CG measurement, and up to several days for a complete test.

The capabilities of the servo press for varying the ram speed during stroke and for adjusting the stroke length are well known. Various companies installed servo presses for blanking. Some of the considerations may include increase in productivity and flexibility in adjusting the ram stroke, noise reduction and improvement of edge quality of blanked edge. The objectives of this study are to determine the effect of ram (blanking) speed upon the edge quality, and the effect of multiple step blanking using several punch motions, during one blanking stroke.

Vaporizing Foil Actuators (VFA) are based on the phenomenon of rapid vaporization of thin metallic foils and wires, caused by passage of a capacitor bank driven current on the order of 100 kA. The burst of the conductor is accompanied with a high-pressure pulse, which can be used for working metal at high strain rates. This paper focuses on the use of VFA for collision welding of dissimilar metals, in particular, aluminum and steel. Aluminum alloy 6061 sheets of 1 mm thickness were launched to velocities in excess of 650 m/s with input electrical energy of 8 kJ into 0.0762 mm thick, dog-bone shaped aluminum foil actuators. Target sheets made from dual phase steel (DP780) were impacted with the aluminum flyer sheet, and solid state impact welds were created. During mechanical testing, many samples failed outside the weld area, thereby indicating that the weld was stronger than the parent aluminum.

Electronic stability control (ESC) has been an essential part of road vehicle safety for almost three decades. In April of 2007, the United States federal government issued a regulation to test the validity of ESC in development vehicles, and the regulation is called Federal Motor Vehicle Safety Standards (FMVSS) 126 in North America (NA), and an equivalent test in other countries outside of NA called ECE13-H (Economic Commission for Europe). While these standards have been used to certify ESC in development passenger cars for over a decade, this has not yet been scrutinized for the application of autonomous vehicles. Autonomous cars have sensors and control systems which can be used to improve ESC, where commercial standard vehicles do not.

Sled testing procedures should reflect a rigorous level of repeatability across trials and reproducibility across testing facilities. Currently, different testing facilities use various methods to set the harness tension for child restraint system (CRS) sled tests. The objective of this study is to identify which harness tightening procedure(s) produce tensions within a reasonable target range while showing adequate reproducibility, repeatability, and ease-of-use. Five harness tightening procedures were selected: A) FMVSS 213 procedure, B) a 3-prong tension gauge, C) ECE R44/R129 procedure, D) two finger method, and E) pinch test. Two CRS models were instrumented with a tension load cell in the harness system. Seven sled room operators were recruited to perform each of the five harness tightening procedures for ten repetitions apiece on both instrumented CRS using a Hybrid III 3-year-old.

Edge fracture is a common problem when forming advanced high strength steels (AHSS). A particular case of edge fracture occurs during a collar forming/hole extrusion process, which is widely used in the sheet metal forming industry. This study attempts to relate the edge stretchability in collar forming to the strain hardening along the pierced edge; thus, Finite Element (FE) simulations can be used to reduce the number of experiments required to improve cutting settings for a given material and thickness. Using a complex-phase steel, CP-W 800 with thickness of 4.0 mm, a single-stage piercing operation is compared with a two-stage piercing operation, so called shaving, in terms of strains along the pierced edge, calculated by FE simulation. Results indicated that strains were reduced along the pierced edge by shaving.

A single-vehicle crash involving an SUV led to the study of the failure of the anti-sway bar linkage and tire pressure and their relative effects on the handling characteristics of the vehicle. The SUV, having been involved in a rollover, was found with the anti-sway bar drop link disconnected from the suspension lower A-arm assembly. Also, after the crash, the tire pressure in the front tires on the subject vehicle was measured to be above the value specified by the SUV manufacturer; however, the pressure for one of the rear tires was measured to be roughly half of the SUV manufacturer’s recommended pressure. The other rear tire was deflated. The testing described herein addresses the question of what effects the anti-sway bar drop link disconnection or reduced rear axle tire pressure would have on the SUV’s pre-accident handling and driveability.