Search Results

This study focuses on the combustion visualization of spark ignition combustion in an optical single cylinder engine using natural gas and propane at several air to fuel ratios and speed-load operating points. Propane and natural gas fuels were compared as they are the most promising gaseous alternative fuels for reciprocating powertrains, with both fuels beginning to find wide market penetration on the fleet level across many regions of the world. Additionally, when compared to gasoline, these gaseous fuels are affordable, have high knock resistance and relatively low carbon content and they do not suffer from the complex re-fueling and storage problems associated with hydrogen.

The development of connected-vehicle technology, which includes vehicle-vehicle and vehicle-infrastructure communications, opens the door for unprecedented active safety and driver-enhanced systems. In addition to exchanging basic traffic messages among vehicles for safety applications, a significantly higher level of safety can be achieved when vehicles and designated infrastructure-locations share their sensor data. In this paper, we propose a new system where cameras installed on multiple vehicles and infrastructure-locations share and fuse their visual data and detected objects in real-time. The transmission of camera data and/or detected objects (e.g., pedestrians, vehicles, cyclists, etc.) can be accomplished by many communication methods. In particular, such communications can be accomplished using the emerging Dedicated Short-Range Communications (DSRC) technology.

This paper describes the design, implementation and testing of crankshaft-mounted pendulum absorbers used for reducing vibrations in a variable displacement engine. The engine can run in V8 and V4 modes, and without absorbers it experiences significant vibration levels, especially in V4 idle. The absorbers are tuned to address the dominant second order vibrations, and are slightly overtuned to account for nonlinear effects. The absorbers were designed to replace the large counterweights at the ends of the crankshaft, and thus serve for both balancing and vibration absorption. The engine was placed in a vehicle and tested for vibration levels at idle under various load conditions, and these results were compared with results obtained from a similar vehicle without absorbers. The tests demonstrate that these absorbers offer an effective means of vibration attenuation in variable displacement engines.

A versatile acceleration facility is described which accelerates and decelerates a sled or a modified automobile on its own wheels. The same propulsion and snubber systems are used for both the sled and the vehicle configurations with less than an hour required between runs. Accelerations and decelerations up to 60 g, velocities up to 60 mph, onsets of 200-2000 g/sec, acceleration distances up to 10 ft and deceleration distances up to 6 ft are available with excellent reproducibility. Extensive safety features for the operating personnel are provided.

Continuous efforts to improve thermal efficiency and reduce exhaust emissions of internal combustion engines have resulted in development of various solutions towards improved lean burn ignition systems in spark ignition engines. The Dual Mode, Turbulent Jet Ignition (DM-TJI) system is one of the leading technologies in that regard which offers higher thermal efficiency and reduced NOx emissions due to its ability to operate with very lean or highly dilute mixtures. Compared to other pre-chamber ignition technologies, the DM-TJI system has the distinct capability to work with a very high level of EGR dilution (up to ~40%). Thus, this system enables the use of a three-way catalyst (TWC). Auxiliary air supply for pre-chamber purge allows this system to work with such high EGR dilution rate. This work presents the results of experimental investigation carried out with a Dual Mode, Turbulent Jet Ignition (DM-TJI) optical engine equipped with a cooled EGR system.

Surface coatings are one of the most widely used routes to enhance the tribological properties of cylinder kits due to effective sealing capability with low friction coefficient and high wear resistance. In the current study, we have conducted the surface texture characterization of the coating on piston skirts and evaluated the impact of a novel Abradable Powder Coating (APC) on cylinder-kit performance in comparison to stock pistons. The surface texture and characteristic properties varying across the piston skirt are obtained and analyzed via a 3D optical profiler and OmniSurf3D software. The engine operating conditions are found through a combination of measurements, testing, and a calibrated GT-Power model. The variable surface properties along with other dimensions, thermodynamic attributes, flow characteristics and material properties are used to build a model in CASE (Cylinder-kit Analysis System for Engines)- PISTON for both an APC coated piston and a stock piston.

Human intraspecific variation is a complex problem, but may be better understood by using computational models in tandem with knowledge about the genetic bases of phenotypic traits. These results can be used in a multitude of settings. To move closer to this goal, biologically-realistic mappings between genotype and phenotype are constructed using genetic algorithm and neural network-like models. These models allow for gene-gene and gene-environment interactions to be characterized in the resulting phenotype. Two types of model are introduced: a simple, two-layer model, and a more complex model. The final section will focus on trends of growth and development in relation to relationship to modeling anthropometric traits and other morphological phenomena.

Understanding cylinder-kit tribology is pivotal to durability, emission management, reduced oil consumption, and efficiency of the internal combustion engine. This work addresses the understanding of the fundamental aspects of oil transport and combustion gas flow in the cylinder kit, using simulation tools and high-performance computing. A dynamic three-dimensional multi-phase, multi-component modeling methodology is demonstrated to study cylinder-kit assembly tribology during the four-stroke cycle of a piston engine. The percentage of oil and gas transported through different regions of the piston ring pack is predicted, and the mechanisms behind this transport are analyzed. The velocity field shows substantial circumferential flow in the piston ring pack, leading to blowback into the combustion chamber during the expansion stroke.

Injury to the lower extremity during an automotive crash is a significant problem. While the introduction of safety features (i.e. seat belts, air bags) has significantly reduced fatalities, lower extremity injury now occurs more frequently, probably for a variety of reasons. Lower extremity trauma is currently based on a bone fracture criterion derived from human cadaver impact experiments. These impact experiments, conducted in the 1960's and 70's, typically used a rigid impact interface to deliver a blunt insult to the 90° flexed knee. The resulting criterion states that 10 kN is the maximum load allowed at the knee during an automotive crash when certifying new automobiles using anthropomorphic dummies. However, clinical studies suggest that subfracture loading can cause osteochondral microdamage which can progress to a chronic and debilitating joint disease.

Cylinder-kit tribology has been a significant focus in developing internal combustion engines of lower emission, reduced friction and oil consumption, and higher efficiency. This work addresses the impact of ring-groove geometry on oil (liquid oil and oil vapor) transport and combustion gas flow in the cylinder kit, using a dynamic three-dimensional multiphase modeling methodology during the four-stroke cycle of a piston engine. The ring and groove geometry, along with the temperature and pressure conditions at the interface between piston and liner, trigger the oil and gas (combustion gases and oil vapor) transport. A study of the second ring dynamics is presented to investigate the effect of negative ring twist on the three-dimensional fluid flow physics. The oil (liquid oil and oil vapor) transport and combustion gas flow processes through the piston ring pack for the twisted and untwisted geometry configurations are compared.

Over the years, many studies have examined the natural gas flame characteristics with either CO2, H2O, or N2 dilution in order to investigate the exhaust gas recirculation (EGR) effect on the performance of natural gas vehicles. However, studies analyzing the actual EGR concentration are very scarce. In the present study, spherically expanding flames were employed to investigate the EGR effect on the laminar flame speed (LFS) and the burned gas Markstein length (Lb) of premixed CH4/air flames at 373 K and 3 bar. The EGR mixture was imitated with a mixture of 9.50% CO2 + 19.01% H2O + 71.49% N2 by mole. EGR ratios of 0%, 5%, 10%, and 15% were tested. Experimental results show that LFS values are lowered by 20-23%, 38-43% and 53-54% due to 5%, 10% and 15% EGR, respectively. Additionally, it was observed that Lb values slightly increase at high equivalence and EGR ratios, where CH4 flames are more stable and more stretched.

This paper presents a computational investigation of the validity of eddy current testing (ECT) for defects embedded in steel using parametrically designed defects. Of particular focus is the depths at which defects can be detected through ECT. Building on this we characterize interior defects by parametrically describing them and then examining the response fields through measurement. Thereby we seek to establish the depth and direction of detectable cracks. As a second step, we match measurements from eddy current excitations to computed fields through finite element optimization. This develops further our previously presented methods of defect characterization. Here rough contours of synthesized shapes are avoided by a novel scheme of averaging neighbor heights rather than using complex Bézier curves, constraints and such like. This avoids the jagged shapes corresponding to mathematically correct but unrealistic synthesized shapes in design and nondestructive evaluation.

This paper presents a review of the core functions and decisions of transportation and traffic management in the automobile industry. Its purpose is to present the concepts within a revised framework which is set in a logistical channels context. Using this approach it easier to see the interdependence which is necessary between shippers and carriers that handle raw materials, component parts, and finished products.

Natural gas is a promising alternative fuel as it is affordable, available worldwide, has high knock resistance and low carbon content. This study focuses on the combustion visualization of spark ignition combustion in an optical single cylinder engine using natural gas at several air to fuel ratios and speed-load operating points. In addition, Turbulent Jet Ignition optical images are compared to the baseline spark ignition images at the world-wide mapping point (1500 rev/min, 3.3 bar IMEPn) in order to provide insight into the relatively unknown phenomenon of Turbulent Jet Ignition combustion. Turbulent Jet Ignition is an advanced spark initiated pre-chamber combustion system for otherwise standard spark ignition engines found in current passenger vehicles. This next generation pre-chamber design simply replaces the spark plug in a conventional spark ignition engine.

Since the 1960's, automotive seats have been designed and evaluated with tools and procedures described in the SAE Recommended Practice J826. The SAE J826 design template and testing manikin each have a torso with a flat lower back shape and with a single joint at the H-point. The JOHN models provide a more anatomically detailed representation of human shape and movement. The articulations of the JOHN torso (pelvic, lumbar, and thoracic) segments are coupled so that their relative positions are determined by a single parameter related to spinal curvature. This paper describes the development and use of the JOHN biomechanical models for seating design.

The need for increased fuel efficiency in conventional automobiles has motivated the design of lightweight, single passenger, super mileage vehicles. Typical low budget super mileage vehicles are capable of attaining 1000 to 1500 miles per gallon of gasoline. The present work discusses unique features of a high mileage vehicle designed and constructed by a research coterie at Michigan State University. More significant contributions of the coterie include an electronic engine and vehicle control system, a vehicle operation optimization analysis, and a computerized method of designing cam lobes based on flow mach numbers. These subjects are considered along with several customary design problems.

This paper describes additional and more recent results from the DaimlerChrysler study of HANS that includes a sensitivity analysis of HANS performance to variations in crash dummy neck length and other impact test conditions. The objective of the tests was to determine the robustness of the HANS concept in a variety of conditions that might occur in actual use. The results show that the variations in test parameters do effect injury measures from the crash dummy, but HANS provides substantial reductions in injury potential in all cases compared to not using HANS. Also, no injuries were indicated with HANS.

The subject of offtracking has been considered as a low speed phenomenon, amenable to analysis via small mechanical models or straightforward calculations. This paper views offtracking from a high speed as well as a low speed vantage point. A mathematical model with one degree of freedom is used to show that there is a speed, well within the routine driving range and independent of radius, at which there will be no offtracking in a steady turn. At higher speeds the trailer will track outside the steady turn circle, and at lower speeds the trailer will track inside the steady turn circle. The analysis indicates similar behavior in a lane change maneuver - small offtracking was found to occur at the steady turn zero-off tracking speed, and larger off tracking was found to occur at both higher and lower speeds.

The paper presents reportage of the debate on the topic expressed by its title that was held as a special session at the SAE 2003 Congress, supplemented by commentaries on its highlights. The debate brought to focus the fact that fuel cells are, indeed, superb powerplants for automobiles, while hydrogen is at the pinnacle of superiority as the most refined fuel. The problems that remained unresolved, are: (1) when fuel cells will be practically viable to replace internal combustion engines and (2) under what circumstances hydrogen, as the ultimate fuel, will be economically viable in view of its intrinsically high cost and hazards engendered by its extraordinary flammability and explosive tendency.

Deep learning based approaches for object detection are heavily dependent on the nature of data used for training, especially for vehicles driving in cluttered urban environments. Consequently, the performance of Convolutional Neural Network (CNN) architectures designed and trained using data captured under clear weather and favorable conditions, could degrade rather significantly when tested under cloudy and rainy conditions. This naturally becomes a major safety issue for emerging autonomous vehicle platforms relying on CNN based object detection methods. Furthermore, despite a noticeable progress in the development of advanced visual deraining algorithms, they still have inherent limitations for improving the performance of state-of-the-art object detection. In this paper, we address this problem area by make the following contributions.