Search Results

The increasing use of downsized turbocharged gasoline engines for passengers cars and the new European homologation cycles (WLTC and RDE) both impose an optimization of the whole engine map. More weight is given to mid and high loads, thus enhancing knock and overfueling limitations. At low and moderate engine speeds, knock mitigation is one of the main issues, generally addressed by retarding spark advance thereby penalizing the combustion efficiency. At high engine speeds, knock still occurs but is less problematic. However, in order to comply with thermo-mechanical properties of the turbine, excess fuel is injected to limit the exhaust gas temperature while maximizing engine power, even with cooled exhaust manifolds. This also implies a decrease of the combustion efficiency and an increase in pollutant emissions. Water injection is one way to overcome both limitations.

In order to reach OEMs acoustic treatment targets (improving performance while minimizing the weight and cost impact), we have developed an original hybrid approach called “Vehicle Acoustic synthesis method”[1] to simulate - and therefore to optimize - noise treatments for both insulation and absorption, and to calculate the resulting Sound Pressure Level (SPL) at ear points for the middle and high frequency range. To calculate the SPL, we identify equivalent volume velocity sources from intensity measurements, and combine them to acoustic transfer functions (panel/ear) measured or computed with ray tracing codes using the reciprocity principle. Compared to our first approach [1], this paper shows a new measurement technique using pressure-particle velocity probes [2]. This technique allows to reduce acquisition time by a factor four, and makes therefore possible a synthesis method on a complete car within two weeks.

This paper presents the following VAN concept led by a vehicle analysis: electrical architecture must not be basically changed in order to be cost effective; efficiency, interoperability and safety aspects must be rigorously respected to avoid lack of quality. As a consequence VAN solutions meet the requirement set concerning wiring, transceivers, protocol controllers and software services. Each of these solutions is optimized to assure safety and easy use. VAN transceivers support multiplexed applications - even high speed application - with conventional wiring. VAN controllers offer a large diversity of services, so allow the minimization of network load, of CPU load, with a high Real Time efficiency. Moreover their structure is very open to diagnosis requirements. VAN softwares provide simple, reliable, reusable mechanisms of sharing, exchange and synchronization. Such mechanisms minimize cost development and guarantee safety proofs in the liability context.

Combustion in any engine starts with the injection of fuel into the combustion chamber. Atomization of fuel and its mixing plays a vital role in determining the suitable air-fuel (A/F) ratio. Appropriate A/F ratio determines the amount of energy release and pollutant formation for standard engines. Thus an accurate prediction of these processes is required to perform reliable combustion and pollutant formation simulations. In this study, the Eulerian-Lagrangian Spray Atomization (ELSA) model is implemented as a Computational Fluid Dynamics (CFD) tool for the prediction of spray behavior. Past studies performed on diesel fuel suggest good agreement between experiment and simulation indicating the model’s capability. The study aims to validate the ELSA model for gasoline fuel against the test results obtained from Renault and against the pure Lagrangian spray model. The simulations have been performed using CONVERGE CFD v2.4.18.

To improve the prediction of the combustion processes in spark ignition engines, a 0D flame/wall interaction submodel has been developed. A two-zones combustion model is implemented and the designed submodel for the flame/wall interaction is included. The flame/wall interaction phenomenon is conceived as a dimensionless function multiplying the burning rate equation. The submodel considers the cylinder shape and the flame surface that spreads inside the combustion chamber. The designed function represents the influence of the cylinder walls while the flame surface propagates across the cylinder. To determine the validity of the combustion model and the flame/wall interaction submodel, the system was tested using the available measurements on a 2 liter SI engine. The model was validated by comparing simulated cylinder pressure and energy release rate with measurements. A good agreement between the implemented model and the measurements was obtained.

This study deals with a coupled experimental and modeling approach of Diesel Particulate Filter cracking. A coupled model (heat transfer, mass transfer, chemical reactions) is used to predict the temperature field inside the filter during the regeneration steps. This model consists of assembled 1D models and is calibrated using a set of laboratory bench tests. In this set of experiments, laboratory scale filters are tested in different conditions (variation of the oxygen rate and gas flow) and axial/radial thermal gradient are recorded with the use of thermocouples. This model is used to build a second set of laboratory bench tests, which is dedicated to the understanding of the phenomena of Diesel Particulate Filter cracking.

In order to address the CO₂ emissions issue and to diversify the energy for transportation, CNG (Compressed Natural Gas) is considered as one of the most promising alternative fuels given its high octane number. However, gaseous injection decreases volumetric efficiency, impacting directly the maximal torque through a reduction of the cylinder fill-up. To overcome this drawback, both independent natural gas and gasoline indirect injection systems with dedicated engine control were fitted on a RENAULT 2.0L turbocharged SI (Spark Ignition) engine and were adapted for simultaneous operation. The main objective of this innovative combination of gas and liquid fuel injections is to increase the volumetric efficiency without losing the high knocking resistance of methane.

In order to assist in fast design cycle of Diesel engines selective catalytic reduction (SCR) exhaust systems, significant endeavor is currently being made to improve numerical simulation accuracy of urea thermo-hydrolysis. In this article, the achievements of a recently developed urea semi-detailed decomposition chemical scheme are assessed using three available databases from the literature. First, evaporation and thermo-hydrolysis of urea-water solution (UWS) single-droplets hanged on a thin thermocouple ring (127 μm) as well as on a thick quartz (275 μm), have been simulated at ambient temperature conditions ranging from 473K to 773K. It has been shown that the numerical results, in terms of evaporation rate and urea gasification, as well as droplet temperature history are very close to the experiments if the heat flux coming from the droplet support is properly accounted for.

An innovative alternative to overcome the load limits of the early injection highly premixed combustion concept consists of taking advantage of the intrinsic characteristics of two-stroke engines, since they can attain the full load torque of a four-stroke engine as the addition of two medium load cycles, where the implementation of this combustion concept could be promising. In this frame, the main objective of this investigation focuses on evaluating the potential of the early injection HPC concept using a conventional diesel fuel combined with a two-stroke poppet valves engine architecture for pollutant control, while keeping a competitive engine efficiency. On a first stage, the HPC concept was implemented at low engine load, where the concept is expected to provide the best results, by advancing the start of injection towards the compression stroke and it was confirmed how it is possible to reduce NOX and soot emissions, but increasing HC and CO emissions.

In this study, the impact of the intake valve timing on knock propensity is investigated on a dual-fuel engine which leverages a low octane fuel and a high octane fuel to adjust the fuel mixture’s research octane rating (RON) based on operating point. Variations in the intake valve timing have a direct impact on residual gas concentrations due to valve overlap, and also affect the compression pressure and temperature by altering the effective compression ratio (eCR). In this study, it is shown that the fuel RON requirement for a non-knocking condition at a fixed operating point can vary significantly solely due to variations of the intake valve timing. At 2000 rpm and 6 bar IMEP, the fuel RON requirement ranges from 80 to 90 as a function of the intake valve timing, and the valve timing can change the RON requirement from 98 to 104 at 2000 rpm and 14 bar IMEP.

IFP Energies nouvelles (IFPEN) has a large experience in the development of engine simulation platforms. During the last decade, the Dual Flame Model (DFM), a physical 0-dimensional (0D) combustion model designed for Diesel applications, was developed and continuously improved. The DFM formalism allows to represent quite precisely the in-cylinder combustion process scenario, by accounting for the first order relevant physics impacting fuel oxidation. First of all, this allows to account for the impact of engine actuators on combustion (e.g. injection systems performing complex injection strategies, Low Pressure and High Pressure EGR loops,…) and then to describe the pollutant emissions formation processes, being chemical kinetics strongly dependent on the in-cylinder thermochemical conditions. The aim of this communication is to present the potential of using the DFM model in the different stages of a Diesel engine development process for pollutant emissions optimization.

The objective of this paper is to present the results of the GT Power calibration with engine test results of the air loop system technology down selection described in the SAE Paper No. 2012-01-0831. Two specific boosting systems were identified as the preferred path forward: (1) Super-turbo with two speed Roots type supercharger, (2) Super-turbo with centrifugal mechanical compressor and CVT transmission both downstream a Fixed Geometry Turbine. The initial performance validation of the boosting hardware in the gas stand and the calibration of the GT Power model developed is described. The calibration leverages data coming from the tests on a 2 cylinder 2-stroke 0.73L diesel engine. The initial flow bench results suggested the need for a revision of the turbo matching due to the big gap in performance between predicted maps and real data. This activity was performed using Honeywell turbocharger solutions spacing from fixed geometry waste gate to variable nozzle turbo (VNT).

This paper presents an after-treatment architecture combining a close coupled NOx trap and an under floor NOx trap. Instead of simply increasing the volume of the catalyst, we propose to broaden the active temperature window by splitting the LNT along the exhaust line. In order to design this architecture, a complete 1D model of NOx trap has been developed. Validated with respect to experimental data, this model has been useful to define the two volumes of LNT, making significant savings on the test bench exploitation. However, one of the main difficulties to operate the proposed architecture is the NOx purge and sulfur poisoning management. In order to optimize the NOx and sulfur purge launches, we have developed a control strategy based on an embedded reduced LNT model. These strategies have been validated on different driving cycles, by the means of simulation and of vehicle tests using rapid prototyping tools.

In this study, different designs of intake ports for two-stroke Ultra Low Cost Gasoline Direct Injection Engine (ULC-GE) has been analyzed to conclude on best design using steady state analysis in STAR-CD. The four types of intake ports design with two cylinders, each having fourteen ports, have been studied. The basic differences in designs are horizontal inlet entry (perpendicular to cylinder axis) and vertical inlet entry (in-line with cylinder axis) having rotation of flow clockwise and anticlockwise. Each type is further differentiated in eight cases with varying distances between axis of two-cylinder as 85mm, 88mm, 91 mm, 94 mm, 97 mm, 100 mm, 105 mm and 112 mm. These designs are analyzed for four different pressure drops as 10 mbar, 50 mbar, 100 mbar and 150 mbar.

The Engine Combustion Network (ECN) has become a leading group concerning the experimental and computational analysis of engine combustion phenomena. In order to establish a coherent database for model validation, all the institutions participating in the experimental effort carry out tests at well-defined boundary conditions and using wellcharacterized hardware. In this framework, the reference Spray A injectors have produced different results even when tested in the same facility, highlighting that the nozzle employed and its fouling are important parameters to be accounted for. On the other hand, the number of the available Spray A injectors became an issue, due to the increasing number of research centers and simultaneous experiments taking place in the ECN community. The present work has a double aim: on the one hand, to seek for an appropriate methodology to “validate” new injectors for ECN experiments and to provide new hardware for the ECN community.

By the action on the steering wheel, the driver has the capability to control the trajectory of its vehicle. Nevertheless, the steering wheel has also the role of information provider to the driver. In particular, the torque level at the steering wheel informs the driver about the interaction between the vehicle and the road. This information flow is natural due to the mechanical chain between the road and the steering wheel. Many studies have shown that steering wheel torque feedback is crucial to ensure the control of the vehicle. In the context of uncoupled steering (steer-by-wire vehicle or driving simulators), the torque rendering on the steering wheel is a major challenge. In addition, of the trajectory control, the quality of this torque is a key for the immersion of drivers in virtual environment such as in driving simulators. The torque-rendering loop is composed of different steps.

Future pollutant emissions legislations are expected to be increasingly stringent. To reduce Nitrogen Oxides (NOx) emissions produced by Diesel engines, advanced combustion technologies - like Low Temperature Combustion (LTC) -, vehicle hybridization and NOx after-treatment systems - such as Selective Catalytic Reduction (SCR) systems - can be considered, leading to a growing demand for NOx models. In this paper, we present a state-of-art of the different existing NOx models, from the black-boxes to the three-dimensional Computational Fluid Dynamics (CFD) codes. A way to classify these models is proposed. The paper also introduces the current applications for each subgroup of models. Then, a black-box and two grey-box NOx models are studied regarding their accuracy and their sensitivity to model inputs. These models are validated for two Diesel engines on steady-state operating points as well as on transient operations. The semi-physical models accurately predict NOx emissions.

Dilution is a promising way to improve fuel economy of Spark-Ignited (SI) gasoline engines. In this context, influence of innovative ignition systems on the dilution acceptance of a 400cc optical GDI engine has been studied. Several systems were tested and compared to a conventional coil: a dual-coil system and two nanosecond scaled plasma generators. Two operating points were studied: 2.8bar IMEP (net) at 2000rpm and 9bar IMEP (net) at 1200rpm. Two diluents were evaluated: real EGR and air (lean combustion). High-speed imaging at frequency up to 10kHz was performed to visualize both spark and combustion initiation and propagation. Voltage and current were measured to infer the energy deposited in the spark plug gap. The dual-coil DCO™ system and the nanosecond multi-pulse plasma generator at their maximum power showed an ability to extend the dilution range of the engine.

Reduction of CO2 emissions is becoming one of the great challenges for future gasoline engines. Downsizing is one of the most promising strategies to achieve this reduction, though it facilitates occurrence of knocking. Therefore, downsizing has to be associated with knock limiting technologies. The aim of the current research program is to adapt the fuel Research-Octane-Number (RON) injected in the combustion chamber to prevent knock occurrence and keep combustion phasing at optimum. This is achieved by a dual fuel injection strategy, involving a low-RON naphtha-based fuel (Naphtha, RON 71) and a high-RON octane booster (Ethanol, RON107). The ratio of fuel quantity on each injector is adapted to fit the RON requirement as a function of engine operating conditions. Hence, it becomes crucial to understand and predict the mixture preparation, to quantify its spatial and cycle-to-cycle variations and to apprehend the consequences on combustion behavior - knock especially.