Search Results

In certain types of city bus service some automatic transmission fluids can fail in less than 10,000 miles. In order to provide satisfactory transmission performance for longer mileage, improved fluids are required. An investigation was undertaken to obtain improved fluids. Fifteen different fluid formulations were evaluated in 30 city buses operated in normal service for more than 2,000,000 miles. It was determined that fluids fail because of frictional deterioration and oxidation. Based on these evaluations, only two fluids were found to be satisfactory for more than 40,000 miles; one additional fluid was satisfactory for more than 30,000 miles. The remaining 12 fluids failed in less than 20,000 miles.

This paper presents an analysis of the economic feasibility of a demand-responsive transportation system employing driver-operated vehicles on existing street networks. The system is designed to meet the general public transportation needs of a suburban community. The analysis follows traditional economic theory in developing demand and supply curves for the transportation service as a consumer good, followed by an investigation of the equilibrium between demand and supply under various market conditions. Cost models specifically applicable to a transportation service with demand-responsive attributes are formulated to calculate the system supply functions, and an attitudinal survey is employed to generate estimates of demand in the case study community. The demand and supply equilibrium situations are investigated with respect to funding alternatives and sensitivity to changes in supply and demand variables.

During development of the General Motors rotary engine, the lubricant was recognized as important to its success because certain lubricants produced deposits which tended to stick both side and apex seals. Consequently, it was decided to develop a rotary engine-dynamometer test, using a Mazda engine, which could be used for lubricant evaluation. In an investigation using an SE engine oil with which there was rotary engine experience, engine operating variables and engine modifications were studied until the greatest amount of deposits were obtained in 100 h of testing. The most significant engine modifications were: omission of inner side seals, plugging of half the rotor bearing holes, pinning of oil seals, grinding of end and intermediate housings, and using a separate oil reservoir for the metering pump. Using this 100 h test procedure, three engine oils and five automatic transmission fluids were evaluated.

A single-wheel trailer has been designed and built to study the origins of tire noise and its basic characteristics. The single test tire, nominally the 10.00/20 size usually mounted on large trucks and semitrailers, is located 12.2 m (40 ft) behind the rear axle of the towing vehicle to isolate it from other noise sources. Reflective surfaces that could interfere with noise measurements are minimized by the high, single-beam construction of the trailer. The towing vehicle is modified to reduce its noise and wake in the vicinity of the test tire, which can be loaded to 22.2 kN (5000 lb) by dead weights and rolled at expressway speeds. Because of its unusual configuration, the dynamic behavior of the trailer was studied prior to design to help determine several design parameters and show that the trailer would follow well. Extensive stress analyses of the trailer beam and other structural elements were also required.

The principal objectives of this study were first to obtain experimental curves of angulation versus moment of resistance of the human neck in hyperextension and lateral flexion, and second to determine angular limits short of significant injury observable in the unembalmed subjects employed in the study. The first of the tests were of the “static” type with load applied over a period of approximately 1s. To determine the applicability of the data to dynamic conditions, tests were also made of the dissected neck at angulation velocities comparable with those of typical accidental injury. Overall resisting moment and injury threshold were similar under the dynamic loading, but somewhat greater moment of resistance was noted during the (earlier) portion of the loading cycle when angular velocity was greatest.

A facility for the aerodynamic testing of scale model vehicles has been developed. Suitable test section geometry, ground plane simulation, model setup technique, flow quality, and aerodynamic force and moment measurement capability are provided for automobile models of 1/4 to 3/8 scale. The maximum velocity of 160 mph enables 3/8 scale, 120 in wheelbase vehicles to be tested at Reynolds numbers approaching 5 × 106, based on wheelbase. A 3/8 scale model in a 160 mph airstream is dynamically similar to full-scale tests at 60 mph. Details of the facility are described.

One of the prime requisites for automobile radar systems is obstacle hazard evaluation, the extent needed being dependent upon the particular system application. Much of the information necessary for a radar system to assess the degree of hazard of a target must come from characteristics which can be measured by the radar itself. While the hazard evaluation capacity has not yet been developed for automobile radar systems, research to provide this capability is in progress. Continuous wave (CW) scattering measurements have been made in a manner which is consistent with automobile radar operation. Various aspects of simple targets and of an automobile were measured in a microwave anechoic chamber. Both horizontal and vertical linear polarizations were transmitted and their co-linear and cross polarizations received. These data have been used to confirm the existence of and to understand certain scattering mechanisms.

The conflicts in the design of turbines for an automotive gas turbine engine are examined. Considerations of stress, efficiency, engine and vehicle acceleration requirements, and compatibility of the flow path are shown to impose a number of opposing requirements. The philosophies used to compromise the conflicts in two successive engine designs are presented. Following a discussion of turbine test facilities, test results are presented for a typical turbine.

This paper evaluates the tendency of lip seals to fracture in a test apparatus in which dynamic runout is 0.010 in and the temperature is cycled between -30 and 0 F. Seals made of eight different polyacrylate polymers were soap-sulfur cured with various types and amounts of carbon black. Physical tests included room-temperature flexibility defined by Young's modulus at small strains, standard tensile tests at room temperature, flexibility at sub-zero temperatures determined by a Gehman test, and sub-zero starting torques of the seals. Primary determinant of successful fracture resistance is a low starting torque resulting from good low-temperature flexibility. The effect of adding graphite to some of these formulations is described and some current commercially available seals are evaluated.

As the design of automobiles changed over the past seventy years, manufacturers have increased the usage of decorative trim to further enhance the beauty of styling concepts. As new trim materials were introduced and parts became more complicated in design, producers have continued their efforts to produce decorative trim parts which remain attractive during the service life of the automobile. The service performance of trim materials in several geographic locations, the use of accelerated tests to predict service performance, recent developments in improving the durability of plated parts, and requirements for producing quality exterior decorative trim are reviewed in this paper.

EXTENSIVE TESTING by GM Research Laboratories has screened five promising transaxle fluids out of 32 mineral-oil-base fluids, 10 synthetic-base fluids, and numerous additive-base stock combination fluids. This paper discusses the findings of the testing and the continuing program on the five fluids. Transaxle fluids have a number of properties affecting performance, including: High-temperature viscosity. Low-temperature fluidity. Shear resistance. Friction properties. Oxidation resistance. Antifoam quality. Effect on seals. Fluid-clutch plate compatibility. Antiwear quality. Extreme-pressure quality. Antirust and anticorrosion qualities.*

This paper illustrates by way of two practical examples, namely, transmission gears and crankshafts, how the automotive industry applies basic approaches and methods for achieving fatigue resistant design. Analytic, laboratory, and field studies necessary in the development of these components are briefly outlined.

Several polymeric materials were developed and evaluated for possible inclusion in the neck structure of state-of-the-art anthropomorphic dummies. These included three types of foam-polyvinylchloride, polyethylene, and polyurethane, and two flexible polymers-polyurethane and a polyvinylchloride chlorinated polyethylene blend (PVC-CPE). Two materials, the polyurethane elastomer and the PVC-CPE blend, were found to be satisfactory in their dynamic response. Because of the ease of casting, the polyurethane material will be used in the GMR 1 state-of-the-art dummy.

This paper defines the overall problem of electromotive interference (EMI) from an automotive viewpoint. First, the general conditions (coupling modes) that apply within the automobile are described, then the automobile as a source of interference is examined. Performance criteria for electromagnetic automobile radiation limits as defined by various organizations are compared. Methods of measuring EMI are discussed, then the authors examine the environment both inside and outside of the automobile. Finally, the paper presents detailed test results of automotive impedance studies.

Engine oil test Sequences IIA and IIIA have been developed to replace Sequences I, II, and III. These new sequences are designed to evaluate lubricants for use in current passenger car engines under severe (MS) service conditions. Lubricant performance is evaluated with respect to scuffing wear, rust, corrosion, deposits, and rumble. The Sequence IIA and IIIA test procedure involves major changes which affect the evaluation of engine rusting and provides improved correlation between test results and short-trip service. Average engine rust ratings correlate with service data within ±0.5 numbers. The new test also provides better repeatability and reproducibility in a significantly shorter schedule. The rust repeatability and reproducibility is less than ±0.2 and ±0.6 numbers, respectively. Test time has been reduced 52%.

Tire nonuniformities are a major source of vibration problems in vehicles. There is considerable disagreement on which tire uniformity parameters are important to vehicle noise and vibration problems, and on how these uniformity parameters should be measured. This paper is concerned primarily with the effects of the nonuniformities of the tire structure which cause contact patch force variations as the tire is rolled in a straight line at constant axle height. Experimental results showing the effects of mean radial load and roll size on these structural, or static, nonuniformities are presented which indicate that these force variations should be measured on a large roll at rated load. Mathematical analyses of certain vehicle vibrations show that radial and lateral force variation are important uniformity parameters. The amplitude of the first harmonic of these force variations contributes to vehicle shake.

The primary forces and moments which affect the directional control properties of wheeled vehicles are those between the road and the rolling tire. These forces and moments are nonlinear functions of a large number of parameters including slip angle, camber angle, vertical load, tire-road friction coefficient, and traction forces, among others. A new apparatus particularly suited to the measurement of the steady state tire properties most significant in handling studies is described. The forces and moments of interest are defined and typical results fora7.60-15 tire are presented to illustrate the effects of slip angle, camber angle, vertical load, inflation pressure, and wheel torque on lateral force and aligning torque.

Two steam-powered passenger ears have been designed, built, and tested. The SE-101 is an intermediate sport coupe incorporating the comfort and convenience features of a modern passenger car and vehicle performance comparable to a low-powered automobile. The SE-124 is a very low-power intermediate sedan with manual start and semiautomatic control. The characteristics of these cars were evaluated relative to the operational requirements of current transportation needs, with particular emphasis on exhaust emissions. Start-up time, exhaust emissions, fuel economy, acceleration, and water consumption data are presented. Although any one of these characteristics may be improved at the expense of others, it does not appear that any compromise can satisfy all of the areas required by today's motorist.

Conventional radial lip oil seals can be made more effective by utilizing helical grooving beneath the contact lip surface. Miniature hydrodynamic pumps so formed aid the radial lip seal in containing the oil by generating fluid forces opposite in direction to the leakage flow forces. This seal-shaft combination has been termed the Hydroseal. Four factorial experiments were conducted to evaluate the effect of helix angle, groove depth, groove width, and number of grooves on sealing performance. The criterion used as a basis for selecting the optimum design were leakage, wear, hardening of the sealing surface, and pumping capacity. These data indicated that the best hydroseal design was one with three grooves, 0.0003 in. deep, 0.014 in. wide, having a helix angle of 45 deg.

At the 1970 SAE International Automobile Safety Conference, the first experimental chest impact results from a new, continuing biomechanics research program were presented and compared with earlier studies performed elsewhere by one of the authors using a different technique. In this paper, additional work from the current program is documented. The general objective remains unchanged: To provide improved quantification of injury tolerance and thoracic mechanical response (force-time, deflection-time, and force-deflection relationships) for blunt sternal impact to the human cadaver. Fourteen additional unembalmed specimens of both sexes (ranging in age from 19-81 years, in weight from 117-180 lb, and in stature from 5 ft 1-1/2 in to 6 ft) have been exposed to midsternal, blunt impacts using a horizontal, elastic-cord propelled striker mass. Impact velocities were higher than those of the previous work, ranging from 14-32 mph.