Search Results

From the beginning of 1995 on, RB will start the production of the Vehicle Dynamics Control System. A key part of this system is the Yaw Rate Sensor described in this paper. The basic requirements for this sensor for automotive applications are: mass producibility, low cost, resistance against environmental influences (such as temperature, vibrations, EMI), stability of all characteristics over life time, high reliability and designed-in safety. Bosch developed a sensor on the basis of the “Vibrating Cylinder”. The sensor will be introduced into mass production in beginning of 1995.

The Bosch ABS for passenger cars which has been in production since 1978 has been described in numerous publications. Following the gathering of extensive experience with the Bosch ABS and its installation in the different models of passenger car, the concept has been revised with various upgrade levels in order to further optimize braking performance on µ-split road surfaces with different right/left adhesion coefficients, in order further to improve the operation of the system when braking on very slippery road surfaces and also to adapt the control algorithm to four-wheel-drive vehicles with differential locks.

The manufacturers of passenger cars increasingly assign development and production of complete subsystems to the supplying industry. A brake system supplier has to give predictions about system quality and performance long time before the first prototypical system is built or even before the supplier gets the order for system development. Nowadays, the usage of computer-aided system design and simulation is essential for that task. This article presents a tool designed to support the development process. A special focus will be on how to define quality. A formal definition of quality is provided, illustrated and motivated by two examples.

This study reports on laser-based diagnostics to temporally track the evolution of liquid and gaseous fuel in the cylinder of a direct injection production type Diesel engine. A two-dimensional Mie scattering technique is used to record the liquid phase and planar laser-induced fluorescence of Diesel is used to track both liquid and vaporised fuel. LIF-Signal is visible in liquid and gas phase, Mie scattering occurs only in zones where fuel droplets are present. Distinction between liquid and gaseous phase becomes therefore possible by comparing LIF- and Mie-Signals. Although the information is qualitative in nature, trends of spray evolution are accessible. Within this study a parametric variation of injection pressure, in-cylinder conditions such as gas temperature and pressure as well as piston geometry are discussed. Observations are used to identify the most sensitive parameters and to qualitatively describe the temporal evolution of the spray for real engine conditions.

A previous study by the authors has shown an efficiency benefit of up to Δηi = 10 % for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine compared to the homogeneous stoichiometric operation with port fuel injection (PFI). While best efficiencies appeared at extremely lean operation at λ = 3.2, minimum HC emissions were found at λ = 2. The increasing HC emissions and narrow ignition time frames in the extremely lean stratified operation have given the need for a detailed analysis. To further investigate the mixture formation and flame propagation und these conditions, an optically accessible single-cylinder engine was used. The mixture formation and the flame luminosity have been investigated in two perpendicular planes inside the combustion chamber.

The usage of Electronic Diesel Control is increasing with todays stringent emissions regulations. This requirement also necessitates that such systems be versatile to meet the needs of the engine/vehicle manufacturer. EGR, start of injection, and fuel delivery can be electronically controlled. Depending on the design goals of the manufacturer any one or two of these can be controlled for partial and all of them for full Electronic Diesel Control. The development and application process has several critical areas. These include, development of the sensors, application of the different subsystems, failure warning and failure mode operation. All of these must be combined if design goals are to be met. As the capabilities of electronics increase it follows that electronic vehicle systems will also improve. Today impressive results have been achieved with systems that are in full or pilot production.

The antiskid systems which have been on the market for some time are characterized by the fact that they are separate from the brake power-assist unit and are positioned between the master cylinder and the wheel brakes (separate configuration). At present, integrated antiskid systems are also being prepared for launching on the market. In these systems the hydraulic brake power-assist unit performs the functions of brake boosting and partly also of ABS pressure modulation. The principles of ABS pressure modulation in separate and integrated antiskid systems are compared and questions concerning safety are discussed. With the separate ABS (plunger system, return system) the brake circuits are closed, i.e. when braking and also during ABS operation the volume of brake fluid between the master cylinders and the wheel brake cylinders is closed and separated from the energy supply of the hydraulic brake power-assist unit.

The emissions legislation in the US and Europe introduces the need for the application of diesel particulate filters (DPF) in most diesel vehicles. In order to fulfill future OBD legislations, which include more stringent requirements on monitoring the functionality of those particulate filters, new sensors besides the differential pressure sensor are necessary. The new sensors need to directly detect the soot emission after DPF and withstand the harsh exhaust gas environment. Based on multi layer ceramic sensor technology, an exhaust gas sensor for particulate matter (EGS-PM) has been developed. The soot-particle-sensing element consists of two inter-digitated comb-like electrodes with an initially infinite electrical resistance. During the sensor operation, soot particles from the exhaust gas are collected onto the inter-digital electrodes and form conductive paths between the two electrode fingers leading to a drop of the electrical resistance.

Cost reduction of engine management systems (EMS) for two-wheeler applications is the key to utilize their potentials compared to carburetor bikes regarding emissions, fuel economy and system robustness. In order to reduce the costs of a system with port fuel injection (PFI) Bosch is developing an EMS without a manifold air pressure (MAP) sensor. The pressure sensor is usually used to compensate for different influences on the air mass, which cannot be detected via the throttle position sensor (TPS) and mean engine speed. Such influences are different leakage rates of the throttle body and changing ambient conditions like air pressure. Bosch has shown in the past that a virtual sensor relying on model based evaluation of engine speed can be used for a detection of leakage air mass in idling to improve the pre-control of the air-fuel ratio. This provides a functionality which so far was only possible with an intake pressure sensor.

An electronic control of throttle angle is required for safety systems like traction control (ASR) and for advanced engine management systems with regard to further improvements of driving comfort and fuel economy. For applications, in which only ASR is required, two versions of a new traction control actuator (TCA) have been developed. Their function is based on controlling the effective length of the bowden cable between the accelerator pedal and the throttle. Besides retaining the mechanical linkage to the throttle, the concept has no need for a pedal position sensor, which is necessary for a drive-by-wire system. Design and performance of both actuators are described and their individual advantages are compared. Moreover, the communication of the system with ASR and its behaviour with regard to vehicle dynamics are illustrated.

The manufacture of semiconductor sensors requires high investment and does not become economically viable until very high production numbers come into consideration. In the case of low production numbers, of the kind that come into consideration for production startups, and in the case of variations e.g. in the measuring range and similar, as may be the case due to the adaptation of models, it may be more viable to employ other techniques which likewise have a high rationalization potential which comes into effect already at low production numbers and which exhibits greater flexibility. The film techniques offer alternative sensor concepts for many measured quantities, whose production is reasonable in price even at smaller production numbers and possesses the necessary alteration flexibility. Besides these, are the advantages of the laser adjustment and the seamless connection of the evaluation electronics. Even possibilities laying within micro-machining technology can be used.

In order to fulfil emission legislation and achieve good drivability of combustion-engine-powered vehicles, information about the air charge and feedback about the engine condition is necessary. In current systems, different sensors are used, e.g. the MAP (manifold air pressure) sensor and a lambda sensor. Aiming at reducing costs, efforts are being made to reduce the number of sensors while still retrieving the necessary information. Various engine speed based functions are state-of-the-art for automotive engines, e.g. for fuel-calibration, misfire-detection etc. Those functions evaluate the engine speed fluctuations during a working cycle induced by combustion. For multiple-cylinder engines, those influences are overlapping, therefore evaluation possibilities are limited. The work presented is based on the effect that at a single-cylinder engine, there is no overlap of combustion influences of various cylinders on the crankshaft.

The development in electronics for automotive application shows a high speed of improvement over the last 20 years regarding downsizing of all components. This could be achieved despite the harsh environmental conditions we find in vehicles, especially in the engine compartment. Big changes have always required the development of new technologies regarding the production of electronic components. The paper shows technologies which are right now under development to allow the next steps regarding downsizing as well as some examples of possible applications. There is also information regarding the current obstacles for improvements beyond this point as well as basic ideas how to overcome some of them.

The SAE J2716 SENT (Single Edge Nibble Transmission) Protocol has entered production with a number of announced products. The SENT protocol is a point-to-point scheme for transmitting signal values from a sensor to a controller. It is intended to allow for high resolution data transmission with a lower system cost than available serial data solution. The SAE SENT Task Force has developed a number of enhancements and clarifications to the original specification which are summarized in this paper.

Contemporary diesel engines are high-tech power plants that provide high torques at very good levels of efficiency. By means of modern injecting-systems such as Common-Rail Injection, combustion noise and emissions could be influenced positively as well. Diesel engine are therefore used increasingly in top-range and sports cars. Today's production ECUs have no or only very low feedback regarding the process in the combustion chamber. As long as this data is missing, the design of the maps in the ECU can only be a compromise, since production tolerances and aging processes have to be considered in advance. Disturbances in the combustion process may not be detected at all. If more knowledge about the course of combustion is provided, especially the start of combustion (SOC), various operating parameters, such as the pilot injection quantity or the beginning of current feed to the injector, could be adjusted more precisely and individually for every cylinder.

The introduction of new emission legislation and the demand of increased power for small two-wheelers lead to an increase of technical requirements. Especially for single cylinder engines with high compression ratio the transient behavior close to idling is challenging. The demand for two-wheeler specific responsiveness of the vehicle requires low overall rotational inertia as well as small intake manifold volumes. The combination with high compression ratio can lead to a stalling of the engine if the throttle opens and closes very quickly in idle operation. The fast opening and closing of the throttle is called a throttle blip. Fast, in this context, means that the blipping event can occur in one to two working cycles. Previous work was focused on the development of a procedure to apply reproducible blipping events to a vehicle in order to derive a deeper physical understanding of the stalling events.

The introduction of stricter emission legislation and the demand of increased power for small two-wheelers lead to an increase of technical requirements. Especially the introduction of liquid-cooling over air-cooling allows the introduction of higher compression ratios, which improves power output as well as thermodynamic efficiencies and thereby fuel consumption. But an increase in compression ratio also introduces further challenges during transient behavior especially close to idling. In order to keep the two-wheeler specific responsiveness of the vehicle, the overall rotational inertia of the engine must be kept low. But the combination of low inertia and high compression ratio can lead to a stalling of the engine if the throttle is opened and closed very quickly in idle operation. The fast opening and closing of the throttle is called a throttle blip.

A single-chip integrated barometric pressure sensor using bulk silicon micromachining will be presented in this paper. The sensor chip incorporates the complete signal evaluation and trimming of the temperature coefficients and manufacturing tolerances. Sensor chips are mounted onto 6″ × 4″ thick film substrates for batch processing during assembly and trimming. The separated, individual devices can be used for surface mounting (SMD) on a printed circuit board (PCB). Specifications for the sensor functions, as well as the assembly and packaging concept, will be discussed. Assembly, trimming and packaging are the most expensive production steps in the manufacture of sensors. In order to reduce the costs for sensors, we are introducing a standardization of sensor assembly and trimming with batch processing capability: after dicing, the integrated sensor chip is attached to a 6″ × 4″ thick film ceramic substrate with standard die-attaching glue.

We propose a novel method to real-time in-cylinder pressure estimation by processing structure-borne sound measurements. It has been shown that knowledge of the in-cylinder pressure opens the door to robust misfire detection and sophisticated closed loop engine control schemes. However, the costs of such sensors have inhibited their use in production engines. On the other hand, acceleration sensors are of low cost and already mounted on modern production engines for knock detection. Since structure-borne sound is measured on the surface of the engine, all cylinders are simultaneously observed by one sensor. A simple physically based model, describing the speed dependence of the transfer behavior from each in-cylinder pressure to structure-borne sound is developed. Based on this model, a method for identifying the parameterized transfer function speed independently is developed.

This study presents a methodology to predict particle number (PN) generation on a naturally aspirated 4-cylinder gasoline engine with port fuel injection (PFI) from wall wetting, employing numerical CFD simulation and fuel film analysis. Various engine parameters concerning spray pattern, injection timing, intake valve timing, as well as engine load/speed were varied and their impact on wall film and PN was evaluated. The engine, which was driven at wide open throttle (WOT), was equipped with soot particle sampling technology and optical access to the combustion chamber of cylinder 1 in order to visualise non-premixed combustion. High-speed imaging revealed a notable presence of diffusion flames, which were typically initiated between the valve seats and cylinder head. Their size was found to match qualitatively with particulate number measurements. A validated CFD model was employed to simulate spray propagation, film transport and droplet impingement.