Search Results

Future emission norms in India (BS6) necessitates the 2 wheeler industry to work towards emission optimization measures. Engine operation at stoichiometric Air-Fuel Ratio (AFR) would result in a good performance, durability and least emissions. To keep the AFR close to stoichiometric condition, an Oxygen sensor is placed in the exhaust system, which detects if air-fuel mixture is rich (λ<1) or lean (λ>1) and provides feedback to fuel injection system for suitable fuel control. O2 sensor has a ceramic element, which needs to be heated to a working temperature for its functioning. The ceramic element would break (thermal shock) if water in liquid form comes in contact with it when the element is hot.

Traction control (ASR) is the logical ongoing development of the antilock braking system (ABS). Due to the high costs involved though, the widespread practice of reducing the engine power by electronic throttle control (or electronic enginepower control) has up to now prevented ASR from becoming as widely proliferated as ABS. A promising method has now been developed in which fuel-injection suppression at individual cylinders is used as a low-price actuator for a budget-priced ASR. First of all, an overview of the possibilities for influencing wheel-torque by means of intervention at the engine and/or brake as a means of reducing driven wheel slip is presented. Then, the system, the control strategy, and the demands on the electronic engine-management system with sequential fuel injection are discussed. The system's possibilities and its limitations are indicated, and fears of damaging effects on the catalytic converter are eliminated.

For the BMW V8 engine, a new LEV/EU3 emission concept has been developed by improvements to the previous engine management and secondary air supply and a complete new exhaust system. Beside the emission limits, also high engine output targets and high operating reliability were targeted. In addition the new exhaust system had to meet low cost targets. Based on these requirements an exhaust concept with separate pre catalyst and main catalyst was chosen. To reduce the heat mass and to optimize the pressure drop, 4.3mil/400cpsi thin wall ceramic substrates were used for the pre and main catalyst.

To meet LEV and EU Stage III emission requirements, it is necessary for new catalytic converters to be designed which exceed light-off temperature as quickly as possible. The technical solutions are secondary air injection, active heating systems such as the electrically heated catalytic converter, and the close coupled catalytic converter. Engine control functions are extensively used to heat the converter and will to play a significant role in the future. The concept of relocating the converter to a position close to the engine in an existing vehicle involves new conflicts. Examples include the space requirements, the thermal resistance of the catalytic coating and high temperature loads in the engine compartment.

The tightening of Heavy Duty Diesel (HDD) emissions legislation throughout the world is leading to the development of emission control devices to enable HDD engines to meet the new standards. NOx and Particulate Matter (PM) are the key pollutants which these emission control systems need to address. Diesel Particulate Filters (DPFs) are already in use in significant numbers to control PM emissions from HDD vehicles, and Selective Catalytic Reduction (SCR) is a very promising technology to control NOx emissions. This paper describes the development and performance of the Compact SCR-Trap system - a pollution control device comprising a DPF-based system (the Continuously Regenerating Trap system) upstream of an SCR system. The system has been designed to be as easy to package as possible, by minimising the total volume of the system and by incorporating the SCR catalysts on annular substrates placed around the outside of the DPF-based system.

In recent years, car manufacturers have been shifting their efforts towards improving quality of interior noise, rather than simply reducing noise levels. One of the most important issues, which is today widely accepted, is that noise contains information. Slamming noise should warn us that doors are safely closed, control panel pushbutton “clicks” inform us about the correct turning on of devices, etc.. One of the acoustic researchers' task is therefore to modify the original noise to emphasize quality of information and to reduce annoying components. For these reasons, it is very important to affect noise timbre, by investigating the relationships between mechanical and acoustical parameters. In this paper we describe a workstation (which we have called N.O.T.E.: Noise Optimizator for Thermal Engine) for intake and exhaust system noise synthesis, that integrates an acoustical simulation code with a synthesizer.

Secondary air injection after cold start gives two effects for reduced exhaust emissions: An exothermic reaction at the hot exhaust valves occurs, which increases the temperature of the exhaust gas. It gives sufficient air to the catalyst during the cold start fuel enrichment that is necessary to prevent driveability problems. Handicaps for the wide use of air injection include space constraints, weight and price. An electrical air blower was choosen to best satisfy all these requirements. The development steps are described. The result is a three stage radialblower with extremly high revolutions of about 18000 rpm. The system configuration and the outcome are demonstrated on the new C-Class of Mercedes-Benz. The results show emission reductions higher than 50 %, while also satisfying the development goals of noise, volume, weight and cost requirements.

The emissions legislation in the US and Europe introduces the need for the application of diesel particulate filters (DPF) in most diesel vehicles. In order to fulfill future OBD legislations, which include more stringent requirements on monitoring the functionality of those particulate filters, new sensors besides the differential pressure sensor are necessary. The new sensors need to directly detect the soot emission after DPF and withstand the harsh exhaust gas environment. Based on multi layer ceramic sensor technology, an exhaust gas sensor for particulate matter (EGS-PM) has been developed. The soot-particle-sensing element consists of two inter-digitated comb-like electrodes with an initially infinite electrical resistance. During the sensor operation, soot particles from the exhaust gas are collected onto the inter-digital electrodes and form conductive paths between the two electrode fingers leading to a drop of the electrical resistance.

CNG direct injection is a promising technology to promote the acceptance of natural gas engines. Among the beneficial properties of CNG, like reduced pollutants and CO2 emissions, the direct injection contributes to a higher volumetric efficiency and thus to a better driveability, one of the most limiting drawbacks of today’s CNG vehicles. But such a combustion concept increases the demands on the injection system and mixture formation. Among other things it requires a much higher flow rate at low injection pressure. This can be only provided by an outward-opening nozzle due to its large cross-section. Nevertheless its hollow cone jet with a specific propagation behavior leads to an adverse fuel-air distribution especially at higher loads under scavenging conditions. This paper covers numerical and experimental analysis of CNG direct injection to understand its mixture formation.

Modern zirconia oxygen sensors are heated internally to achieve an optimal detection of the oxygen concentration in the exhaust gas and fast light off time. The temperature of the gas in the exhaust pipe varies in a wide range. The zirconia sensor is cooled by radiation and forced convection caused by cold exhaust gas. If the zirconia temperature falls, the oxygen detection capability of the sensor decreases. To minimize the cooling effects, protection tubes cover the zirconia sensor. However, this is in conflict with the aim to accelerate the dynamics of the lambda sensor. In this paper, the heat transfer at the surface of a heated planar zirconia sensor with two different double protection tubes of a Bosch oxygen sensor is examined in detail. The geometric configuration of the tubes forces different flow patterns in the inner protection tube around the zirconia sensor. The zirconia sensor is internally electrically heated by a platinum heater layer.

In new exhaust system specifications such as single cylinder balancing, closed coupled catalyst systems, sensor locations close to the engine, turbo applications, fast light off situations and diesel engine applications the dynamic behavior of the lambda sensor becomes more important. This demands a detailed knowledge and modeling of the relevant parameters. In former analysis of exhaust gas sensors the main focus has been the electrochemical processes in the sensor. The influence of flow structure and protection tubes had lower priority. In this paper we present the numerical and experimental analysis of cold air flowing in a pipe including mounted exhaust sensors. Two double-protection tubes from the Robert Bosch GmbH have been examined named (a) and (b). The predicted results have been compared with values measured with Laser Doppler Anemometry (LDA). The flow pattern in the protection tube type (a) depends on the geometric configuration of the sensor element and the tubes.

Exhaust acoustics simulation is an important part of the exhaust system process. Especially important is the trend towards a coupled approach to performance and acoustics design. The present paper describes a new simulation tool developed for such coupled simulations. This tool is based on a one-dimensional fluid dynamics solution of the flow in the engine manifolds and exhaust and intake elements. To represent the often complex geometries of mufflers, an easy-to-use graphical pre-processor is provided, with which the user builds a model representation of mufflers using a library of basic elements. A comparison made to two engines equipped with exhaust silencers, shows that the predictions give good results.

A local Gaussian process regression approach is presented, which allows to model nonlinearities of internal combustion engines more accurate than global Gaussian process regression. By building smaller models, the prediction of local system behavior improves significantly. In order to predict a value, the algorithm chooses the nearest training points. The number of chosen training points depends on the intensity of estimated nonlinearity. After determining the training points, a model is built, the prediction performed and the model discarded. The approach is demonstrated with a benchmark system and air charge test bed measurements. The measurements are taken from a turbocharged SI gasoline engine with both variable inlet valve lift and variable inlet and exhaust valve opening angle. The results show how local Gaussian process regression outmatches global Gaussian process regression concerning model quality and nonlinearities in particular.

In order to describe simultaneously the thermo-fluid dynamics and the acoustics of an Internal Combustion engine, a mathematical model and a computer program has been developed which integrate the Method of the Characteristics with the Acoustic. Transfer Matrix Method. The former method is currently used to model the fluid dynamics of Internal Combustion engines, whilst the latter allows the description of the acoustical behaviour of the intake and exhaust systems. The theory presented in the article integrates the two approaches, allowing the fluid-acoustics of the global system engine-silencers to be described, taking into account the mutual interactions. Preliminary investigations on a simplified system, constituted of a constant section duct, have demonstrated the consistency and validity of the model.

Apart from the reduction of engine-out emissions from the powerplant, the development of an efficient and reliable catalytic converter heating system is an important task of automotive engineering in the future to meet standards that will require reduction of cold start emissions. Carrying out a comprehensive study in this field, BMW has tested and evaluated possible solutions to this challenge. In additon to the electrically heated catalytic converter (E-cat) and the afterburner chamber, an incorporated burner system would meet the requirement for fast catalyst light-off in the future, particularly in the case of larger engines.

Historically, whenever the automotive solutions’ state of art reaches a saturation level, the integration of new verticals of technology has always raised new opportunities to innovate, enhance and optimize automotive solutions. The predictive powertrain solutions using connectivity elements (e.g., navigation unit, e-Horizon or cloud-based services) are one of such areas of huge interest in automotive industry. The prior knowledge of trip destination and its route characteristics has potential to make prediction of powertrain modes or events in certain order and therefore it can add value in various application areas such as optimized energy management, lower fuel consumption, superior safety and comfort, etc.

The production of the BMW ALPINA B12 5.7 with Switch-Tronic transmission provides the markets of Europe and Japan with an exclusive, luxury-orientated, high performance limited series limousine. This is the first vehicle worldwide to be fitted with the progressive exhaust gas aftertreatment technology known as the Electrically Heated Catalyst (EHC), in which the effectiveness of the power utilized is increased significantly by an alternating heating process for both catalytic converters. Only since this achievement has the implementation of the EHC been viable without extensive modification to the battery and alternator. With this exhaust gas aftertreatment concept, the emissions of this high performance vehicle will fall to less than half the maximum permissible for compliance with 1996 emission standards.

General Motors' 3.6L DOHC 4V V6 engine has been upgraded to provide substantial improvements in performance, fuel economy, and emissions for the 2008 model year Cadillac CTS and STS. The fundamental change was a switch from traditional manifold-port fuel injection (MPFI) to spark ignition direct injection (SIDI). Additional modifications include enhanced cylinder head and intake manifold air flow capacities, optimized camshaft profiles, and increased compression ratio. The SIDI fuel system presented the greatest opportunities for system development and optimization in order to maximize improvements in performance, fuel economy, and emissions. In particular, the injector flow rate, orifice geometry, and spray pattern were selected to provide the optimum balance of high power and torque, low fuel consumption, stable combustion, low smoke emissions, and robust tolerance to injector plugging.

Current exhaust gas emission regulations can only be well adhered to through optimal interplay of combustion engine and exhaust gas after-treatment systems. Combining a modern diesel engine with several exhaust gas after-treatment components (DPF, catalytic converters) leads to extremely complex drive systems, with very complex and technically demanding control systems. Current engine ECUs (Electronic Control Unit) have hundreds of functions with thousands of parameters that can be adapted to keep the exhaust gas emissions within the given limits. Each of these functions has to be calibrated and tested in accordance with the rest of the ECU software. To date this task has been performed mostly on engine test benches or in Hardware-in-the-Loop (HiL) setups. In this paper, a Software-in-the-Loop (SiL) approach, consisting of an engine model and an exhaust gas treatment (EGT) model, coupled with software from a real diesel engine ECU, will be described in detail.