Search Results

Tests were conducted on a variety of commercially available spark plugs to determine the influence of igniter design on initial kernel formation and overall performance. Flame kernel formation was investigated using high-speed schlieren visualization. The flame growth rate was quantified using the area of the burned gas region. The results showed that kernel growth rate was heavily influenced by electrode geometry and configuration. The igniters were also tested in a bomb calorimeter to determine the levels of supplied and delivered energy. The typical ratio of supplied to delivered energy was 20% and igniters with a higher internal resistance delivered more energy and had faster kernel formation rates. The exception was plugs with large amounts of conductive mass near the electrodes, which had very slow kernel formation rates despite relatively high delivered energy levels.

Swirl plane Particle Image Velocimetry (PIV) measurements were performed in a single-cylinder optically accessible gasoline direct injection (DISI) engine using a borescope introduced through the spark plug hole. This allowed the use of a contoured piston and the visualization of the flow field in and around the piston bowl. The manifold absolute pressure (MAP) was fixed at 90 kPa and the engine speed was varied in increments of 250 rpm from 750 rpm to 2000 rpm. Images were taken from 270° to 320° bTDC of compression at 10° intervals to study the evolution of the velocity fluctuations. Measurements were performed with and without fuel injection to study its effect on the in-cylinder flow fields. Fuel was injected at 10 MPa and 5 MPa. The 2-D spatial mean velocities of individual flow fields and their decompositions were averaged over 100 cycles and used to investigate the effects of engine speed and image timing on the flow field.

Biodiesel produced from soybean oil, canola oil, yellow grease, and beef tallow was tested in two heavy-duty engines. The biodiesels were tested neat and as 20% by volume blends with a 15 ppm sulfur petroleum-derived diesel fuel. The test engines were a 2002 Cummins ISB and 2003 DDC Series 60. Both engines met the 2004 U.S. emission standard of 2.5 g/bhp-h NOx+HC (3.35 g/kW-h) and utilized exhaust gas recirculation (EGR). All emission tests employed the heavy-duty transient procedure as specified in the U.S. Code of Federal Regulations. Reduction in PM emissions and increase in NOx emissions were observed for all biodiesels in all engines, confirming observations made in older engines. On average PM was reduced by 25% and NOx increased by 3% for the two engines tested for a variety of B20 blends. These changes are slightly larger in magnitude, but in the same range as observed in older engines.

Particle size distribution and number concentration were measured in the dilute exhaust of a heavy-duty diesel engine for steady-state and transient engine operation using two different dilution systems that included a full flow CVS that was coupled to an ejector pump (CVS-EP), and a double-ejector micro-dilution tunnel (DEMDT) that was connected to engine exhaust close to turbocharger outlet. Measurements were performed using a scanning mobility particle sizer (SMPS), an electrical low pressure impactor (ELPI), and a parallel flow diffusion battery (PFDB). Fuels with sulfur content of about 385 ppm and 1 ppm were used for this work. The PFDB performed well in measuring nanoparticles in the size range below 56 nm when compared with the SMPS. This was especially valid when a distinct log-normal size distribution in the size range below 56 nm in diameter, the upper size limit of the PFDB, was present.

The design of helical Intake ports for swirl generation is a process that has been developed over a number of years through primarily empirical methods. A number of design rules have been established that enable designers to develop ports that approach the state-of-the-art for maximum swirl generation with minimum pressure loss. More recently, computer-aided design (CAD) tools have been introduced that permit geometry and features to be accurately defined by mathematical surface descriptions, and to be parameterized such that derived geometry is updated automatically along with parent features. The author has developed a parametric design approach for helical ports that incorporates the lessons learned from experience into a systematic design procedure. This procedure takes advantage of the current CAD capabilities to expedite the design process and improve the result.

SCR-on-filter, or SCRoF, is an emerging technology for different market segments and vehicle applications. The technology enables simultaneous particulate matter trapping and NOX reduction, and provides thermal management and aftertreatment packaging benefits. However, there is little information detailing the lubricant derived exposure effects on functional SCR performance. A study was conducted to evaluate the impact of various oil consumption pathways on a light duty DOC and SCRoF aftertreatment system. This aftertreatment system was aged utilizing an engine test bench modified to enable increased oil consumption rates via three unique oil consumption pathways. The components were characterized for functional SCR performance, ash morphology, and ash deposition characteristics. This included utilizing techniques, such as SEM / EDS, to evaluate the ash structures and quantify the ash elemental composition.

A zero-dimensional cycle simulation model coupled with a chemical equilibrium model and a two-zone combustion model has been extended to predict nitric oxide formation and emissions from spark-ignited, lean-burn natural gas engines. It is demonstrated that using the extended Zeldovich mechanism alone, the NOx emissions from an 8.1-liter, 6-cylinder, natural gas engine were significantly under predicted. However, by combining the predicted NOx formation from both the extended Zeldovich thermal NO and the Fenimore prompt NO mechanisms, the NOx emissions were predicted with fair accuracy over a range of engine powers and lean-burn equivalence ratios. The effect of injection timing on NOx emissions was under predicted. Humidity effects on NOx formation were slightly under predicted in another engine, a 6.8-liter, 6-cylinder, natural gas engine. Engine power was well predicted in both engines, which is a prerequisite to accurate NOx predictions.

Copper ion exchange procedures were used to prepare zeolite-based catalysts for NOx reduction in lean (oxygen-rich) exhaust. Energy dispersive x-ray fluorescence and scanning electron microscopy analyses confirmed the presence of copper in the zeolite matrix. Zeolites were applied onto honeycomb and foam substrates, and evaluated for catalytic NOx reduction efficiency using engine exhaust. Copper-exchanged zeolite catalysts prepared for this study revealed NOx reduction of 95 percent for a period of seven minutes using previously adsorbed exhaust hydrocarbons as the reducing agent. Experiments using ethylene injection to supplement the exhaust suggest long-term and sustained NOx reduction, initially observed at 52 percent. Experimental results and performance comparisons of ZSM-5, mordenite, and Y-type zeolites are discussed. Zeolite catalysts based on Cu-mordenite showed high levels of initial NOx reduction, while results using Cu-ZSM-5 suggested better long-term activity.

This paper describes a hybrid robust nonlinear control approach for modern diesel engines running low temperature combustion and conventional diesel combustion modes. Using alternative combustion modes has become a promising approach to reduce engine emissions. However, due to very different in-cylinder conditions and fueling parameters for different combustion modes, control of engines operating multiple combustion modes is very challenging. It becomes difficult for conventional calibration / mapping based approaches to produce satisfactory results in terms of engine torque responses and emissions. Advanced control techniques are then demanded to accomplish the tasks. An innovative hybrid control system is designed to track different key engine operating variables at different combustion modes as well as avoid singularity which is inherent for turbocharged diesel engines running multiple combustion modes.

The effect of humidity on the lean misfire limit and emissions from a lean burn, natural gas engine is described in this paper, along with a description of a practical humidity compensation method for incorporation into an electronic control system. Experiments to determine the effects of humidity on the lean limit and emissions are described. Humidity increases were shown to decrease the rate of combustion, reduce NOx emissions, and increase the levels of unburned hydrocarbon (HC) and carbon monoxide (CO) emissions. Data and calculations are also presented which demonstrate that increases in humidity will cause enleanment in a typical closed loop control system utilizing a universal exhaust gas oxygen (UEGO) sensor. A prototype system for humidity sensing and subsequent compensation based on these findings was implemented, and the system was found, through additional testing, to compensate for humidity very effectively.

Advanced combustion strategies used to improve efficiency, emissions, and performance in internal combustion engines (IC) alter the chemical composition of engine-out emissions. The characterization of exhaust chemistry from advanced IC engines requires an analytical system capable of measuring a wide range of compounds. For many years, the widely accepted Coordinating Research Council (CRC) Auto/Oil procedure[1,2] has been used to quantify hydrocarbon compounds between C1 and C12 from dilute engine exhaust in Tedlar polyvinyl fluoride (PVF) bags. Hydrocarbons greater than C12+ present the greatest challenge for identification in diesel exhaust. Above C12, PVF bags risk losing the higher molecular weight compounds due to adsorption to the walls of the bag or by condensation of the heavier compounds. This paper describes two specialized exhaust gas sampling and analytical systems capable of analyzing the mid-range (C10 - C24) and the high range (C24+) hydrocarbon in exhaust.

This project’s objective was to generate experimental data to evaluate the impact of metals doped B20 on diesel particle filter (DPF) ash loading and performance compared to that of conventional petrodiesel. The effect of metals doped B20 vs. conventional diesel on a DPF was quantified in a laboratory controlled accelerated ash loading study. The ash loading was conducted on two DPFs – one using ULSD fuel and the other on B20 containing metals dopants equivalent to 4 ppm B100 total metals. Engine oil consumption and B20 metals levels were accelerated by a factor of 5, with DPFs loaded to 30 g/L of ash. Details of the ash loading experiment and on-engine DPF performance evaluations are presented in the companion paper (Part I). The DPFs were cleaned, and ash samples were taken from the cleaned material. X-ray Fluorescence (XRF), X-Ray Photoelectron Spectroscopy (XPS) and X-Ray Diffraction (XRD) were conducted on the ash samples.

The ASTM Sequence VE test evaluates lubricant performance for controlling sludge deposits and minimizing overhead camshaft lobe wear. ILSAC asked JAMA to develop a new valve train wear replacement test since the Sequence VE test engine hardware will become obsolete in the year 2000. JAMA submitted the JASO specification M 328-951) KA24E valve train wear test. This first report presents the results of technical studies conducted when JASO M 328-95 was reviewed and the ASTM standardized version of the KA24E test (the Sequence IVA) was proposed. The cam wear mechanism was studied with the goal of improving reproducibility and repeatability. Engine torque was specified to stabilize the NOx concentration in blow-by, which improved test precision. Additionally, the specifications for induction air humidity and temperature, oil temperature control, and test fuel composition were modified when the ASTM version of the KA24E test was proposed.

The measurement of piston temperature in a reciprocating engine has historically been a very time-consuming and expensive process. Several conditions exist in an engine that measurement equipment must be protected against. Acceleration forces near 2000 G's occur at TDC in automotive engines at rated speed. Operating temperatures inside the crankcase can range to near 150°C. To allow complete mapping of piston temperature, several measuring locations are required in the piston and data must be obtained at various engine operating conditions. Southwest Research Institute (SwRI) has developed a telemetry-based system that withstands the harsh environments mentioned above. The device is attached to the underside of a piston and temperature data is transmitted to a receiving antenna in the engine crankcase. The key element of this device is a tiny power generator which utilizes the reciprocating motion of the piston to generate electricity thus allowing the transmitter to be self-powered.

Range-extended hybrids are an attractive option for medium- and heavy-duty commercial vehicle fleets because they offer the efficiency of an electrified powertrain with the driving range of a conventional diesel powertrain. The vehicle essentially operates as if it was purely electric for most trips, while ensuring that all commercial routes can be completed in any weather conditions or geographic terrain. Fuel use and point-source emissions can be significantly reduced, and in some cases eliminated, as many shorter routes can be fully electrified with this architecture. Under a U.S. Department of Energy (DOE)-funded project for Medium- and Heavy-Duty Vehicle Powertrain Electrification, Cummins has developed a plug-in hybrid electric Class 6 truck with a range-extending engine designed for pickup and delivery application.

A push for more stringent emissions regulations has resulted in larger, increasingly complex aftertreatment solutions. In particular, oxides of nitrogen (NOX) and particulate matter (PM) have been controlled using two separate systems, selective catalytic reduction (SCR) and the catalyze diesel particulate filter (CDPF), or the functionality has been combined into a single device producing the SCR on filter (SCRoF). The SCRoF forgoes beneficial NO2 production present in the CDPF to avoid NH3 oxidation which occurs when using platinum group metals (PGM) for oxidation. In this study, mixed-metal oxides are shown to oxidize NO to NO2 without appreciable NH3 oxidation. This selectivity leads to enhanced performance when combined with a typical Cu-zeolite catalyst.

The principles of the magnetic-perturbation method of flaw detection and the Barkhausen noise residual stress measurement method are briefly reviewed. It is suggested that they provide very powerful tools for assuring improved ball bearing performance. The methods are applied for the evaluation of ball bearing races. Typical experimental results are presented along with metallurgical sectioning correlation.

A physics-based spark ignition model was developed and integrated into a commercial CFD code. The model predicted the spark discharge process based on the electrical parameters of the secondary ignition circuit, tracked the spark motion as it was stretched by in-cylinder gas motion, and determined the resulting energy deposition to the gas. In concert with the existing kinetic solver in the CFD code, the resulting ignition and flame propagation processes were simulated. The model results have been validated against both imaging rig experiments of the spark in moving air and against engine experimental data. The model was able to replicate the key features of the spark and to capture the cyclic variability of high-dilution combustion when multiple engine cycles were simulated.