Search Results

Automobile body panels made from advanced high strength steel (AHSS) provide high strength-to-mass ratio and thus AHSS are important for automotive light-weighting strategy. However, in order to increase their use, the significant wear damage that AHSS sheets cause to the trim dies should be reduced. The wear of dies has undesirable consequences including deterioration of trimmed parts' edges. In this research, die wear measurement techniques that consisted of white-light optical interferometry methods supported by large depth-of-field optical microscopy were developed. 1.4 mm-thick DP980-type AHSS sheets were trimmed using dies made from AISI D2 steel. A clearance of 10% of the thickness of the sheets was maintained between the upper and lower dies. The wear of the upper and lower dies was evaluated and material abrasion and chipping were identified as the main damage features at the trim edges.

The increasing use of aluminum in the design of Body In White (BIW) structures created the need to develop and verify repair methodologies specific to this substrate. Over the past century, steel has been used as the primary material in the production of automotive BIW systems. While repair methods and techniques in steel have been evolving for decades, aluminum structural repair requires special attention for such common practices as welding, mechanical fastening, and the use of adhesives. This paper outlines some of the advanced verification and testing methodologies used to develop collision repair procedures for the aluminum 2003 Jaguar XJ sedan. It includes the identification of potential failure modes found in production and customer applications, the formulation of testing methodologies, CAE verification testing and component subsystem prove-out. The objective of the testing was to develop repair methodologies that meet or exceed production system performance characteristics.

To support its recycling efforts, Ford Motor Company is using a Raman based instrument, the RP-1, co-developed with SpectraCode Inc. to identify unknown polymeric parts. Our recycling initiative involves detailed dismantling of our vehicles into individual parts, calculating the percentage recyclability and making recommendations for the future use of recycled polymers. While Ford has voluntarily adopted the SAE J1344 marking protocol for identifying part material composition, a large number of unmarked parts still exist and require identification. This identification is being done with the help of RP-1. To facilitate this identification, we have generated an accurate reference library of Raman spectra for comparison to those of unknown materials. This paper will describe the techniques that were used to develop and refine the RP-1 reference library to identify automotive polymers, especially black/dark plastics.

The Corrosion Task Force of the Automotive/Steel Partnership has developed the SAE J2334 cyclic laboratory test for evaluating the cosmetic corrosion resistance of auto body steel sheet. [Ref. 1] Since the publishing of this test in 1997, further work has improved the precision of J2334. In this paper, the results of this work along with the revisions to the J2334 test will be discussed.

The previously developed power-based fuel consumption theory for Internal Combustion Engine Vehicles (ICEV) is extended to Battery Electric Vehicles (BEV). The main difference between the BEV model structure and the ICEV is the bi-directional character of traction motors and batteries. A traction motor model was developed as a bi-linear function of positive and negative traction power. Another difference is that the accessories and cabin heating are powered directly from the battery, and not from the powertrain. The resulting unified model for ICEV and BEV energy consumption has linear terms proportional to positive and negative traction power, accessory power, and overhead, in varying proportions. Compared to the ICEV, the BEV powertrain has a high marginal efficiency and low overhead. As a result, BEV energy consumption data under a wide range of driving conditions are mainly proportional to net traction power, with only a small offset.

The “adequate” number of integration points (NIP) required to achieve accurate springback simulation results is studied in this paper in an effort to clarify confusions reported in the literature and shed light on the origin of the confusion. A bending-under-tension model is adopted where springback solution can be obtained with analytical integration through metal thickness. Numerical integrations are then performed and compared with analytical solution to assess associated errors. A crucial distinction is made in the paper that, the model can be posed either as a displacement-value problem where both tension strain and bending radius are prescribed or as a mixed-value problem where the tension force and bending radius are prescribed. Although they are physically equivalent due to the uniqueness of solution, the numerical solutions are different. The associated errors in springback respond differently to the number of integration points employed.

Advanced features in automotive systems often necessitate the management of complex interactions between subsystems. Existing control strategies are designed for certain levels of robustness, however their performance can unexpectedly deteriorate in the presence of significant uncertainties, resulting in undesirable system behaviors. This limitation is further amplified in systems with complex nonlinear dynamics. Hydro-mechanical clutch actuators are among those systems whose behaviors are highly sensitive to variations in subsystem characteristics and operating environments. In a P2 hybrid propulsion system, a wet clutch is utilized for cranking the engine during an EV-HEV mode switching event. It is critical that the hydro-mechanical clutch actuator is stroked as quickly and as consistently as possible despite the existence of uncertainties. Thus, the quantification of uncertainties on clutch actuator behaviors is important for enabling smooth EV-HEV transitions.

This paper presents a Short Time Fourier Transform based algorithm to identify unknown parameters in fuel dynamics system during engine cold start and warm-up. A first order system is used to model the fuel dynamics in a port fuel injection engine. The feed forward transient fuel compensation controller is designed based on the identified model. Experiments are designed and implemented to verify the proposed algorithm. Different experiment settings are compared.

Direct bypass to DC-DC boost converter in traction inverter increases converter's capability and efficiency significantly by providing a lower loss path for power flow between the battery and DC-link terminal. A bypass using diode is an excellent solution to achieve this capability at low cost and system complexity. Bypass diode operates in the linear operating region (DC Q-point) when the battery discharges through the bypass diode to drive the electric motors. Therefore, thermal stress on the DC-link capacitor is shared between the input and DC-link capacitors through the bypass diode. On the other hand, inverters introduce voltage oscillation in the DC-link terminal which results in unwanted energy oscillation through the bypass diode during battery charging. Both of these phenomena have been explained in details.

Thermally sprayed coatings have used in place of iron bore liners in recent aluminum engine blocks. The coatings are steel-based, and are sprayed on the bore wall in the liquid phase. The thermal response of the block structure determines how rapidly coatings can be applied and thus the investment and floor space required for the operation. It is critical not to overheat the block to prevent dimensional errors, metallurgical damage, and thermal stress cracks. This paper describes an innovative finite element procedure for estimating both the substrate temperature and residual stresses in the coating for the thermal spray process. Thin layers of metal at a specified temperature, corresponding to the layers deposited in successive thermal spray torch passes, are applied to the substrate model, generating a heat flux into the block. The thickness, temperature, and application speed of the layers can be varied to simulate different coating cycles.

Thermal fatigue presents a new challenge in cast aluminum engine design. Accurate thermomechanical stress analysis and reliable failure criterion are the keys to a successful life prediction. It is shown that the material stress and strain behavior of cast aluminum is strongly temperature and strain rate sensitive. A unified viscoplasticity constitutive relation is thus proposed to simultaneously describe the plasticity and creep of cast aluminum components deforming at high temperatures. A fatigue failure criterion based on a damage accumulation model is introduced. Damages due to mechanical fatigue, environmental impact and creep are accounted for. The material stress and strain model and thermal fatigue model are shown to be effective in accurately capturing features of thermal fatigue by simulating a component thermal fatigue test using 3D FEA with ABAQUS and comparing the results with measured data.

Over the past five years, the US Automotive Materials Partnership (USAMP) has brought together representatives from DaimlerChrysler, General Motors, Ford Motor Company and over 40 other participant companies from the Mg casting industry to create and test a low-cost, Mg-alloy engine that would achieve a 15 - 20 % Mg component weight savings with no compromise in performance or durability. The block, oil pan, and front cover were redesigned to take advantage of the properties of both high-pressure die cast (HPDC) and sand cast Mg creep- resistant alloys. This paper describes the alloy selection process and the casting and testing of these new Mg-variant components. This paper will also examine the lessons learned and implications of this pre-competitive technology for future applications.

The proliferation of Unibody construction, for vehicle weight reduction, and the expanded use of precoated steel, for improvement in outer body rust-through protection, has significantly increased the number of bimetallic and crevice unions on U.S. manufactured vehicles. Cyclic corrosion and proving ground testing has shown that these unions are highly active electrochemically, resulting in extensive anodic corrosion and cathodic de-lamination of the paint film. This work examines the individual contribution of each layer of the applied protective coatings package, with respect to applied film thickness, to the reduction of permeation by water, oxygen, and NaCl and resultant corrosion.

A vehicle fleet test has been conducted to determine if octane advantages due to selected cooling system variables persist with stabilized deposits. The variables tested were reduced coolant temperatures, a direct substitution of aluminum for the iron cylinder head and an aluminum head with Unique Cooling. Octane requirements, octane requirement increase (ORI), emissions and fuel economy results are presented and discussed. Engine tests to determine the sensitivity of octane to independently controlled engine temperatures confirmed the primary dependence upon coolant temperature. Additional tests identified some of the variables which cause octane differences among the cylinders of one engine and between engine families.

The process parameters to manufacture structural aluminum alloys are critical to their ductility. In particular, quench rate after solution heat treatment impacts the extent of grain boundary precipitation and the formation of precipitate free zone (PFZ) during later artificial aging. Cu-containing 6XXX alloys used for high strength automotive applications are quench sensitive as the Cu addition leads to Q-phase precipitation at grain boundaries, resulting in loss of ductility, which can negatively affect downstream manufacturing steps such as automotive joining and forming processes. Self-piercing rivet (SPR) joining, is a single step, spot joining process used to mechanically connect sheet materials together in automotive body structures. Ductility has been identified as an important metric of material rivet-ability or the ability to make a successful, crack-free SPR joint.

The effect of friction modifiers on the low-speed frictional properties of automatic transmission fluids (ATFs) was investigated by scanning force microscopy (SFM). A clutch lining material was covered by a droplet of test ATF, and a steel tip was scanned over the sample. The scanning speeds were varied from 0.13 to 8.56 mm /sec, and the frictional force was deduced from the torsion of the SFM cantilever. A reduction in dynamic friction due to the addition of the friction modifier was clearly observed over the entire speed range. This indicates that the boundary lubrication mechanism is dominant under this condition, and therefore surface-active friction modifiers can effectively improve the frictional characteristics. The friction reduction was more pronounced at lower sliding speeds. Thus addition of friction modifiers produced a more positive slope in the μ-ν (friction vs. sliding speed) plots, and would contribute to make wet clutch systems less susceptible to shudder vibrations.

It is anticipated that future gasoline engines will have improved mechanical efficiency and consequently lower exhaust temperatures at low load conditions, although the exhaust temperatures at high load conditions are expected to remain the same or even increase due to the increasing use of downsized turbocharged engines. In 2014, a collaborative project was initiated at Ford Motor Company, Oak Ridge National Lab, and the University of Michigan to develop three-way catalysts with improved performance at low temperatures while maintaining the durability of current TWCs. This project is funded by the U.S. Department of Energy and is intended to show progress toward the USDRIVE target of 90% conversion of hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx) at 150 °C after high mileage aging. The testing protocols specified by the USDRIVE ACEC team for stoichiometric S-GDI engines were utilized during the evaluation of experimental catalysts at all three facilities.

Technical Standards are essential for the expanded use of any engineering material. The Society of Automotive Engineers (SAE) Iron and Steel Castings Committee has been reworking existing, (and issuing new), standards for automotive iron and steel castings. This paper will review the status of the SAE standards for Ductile Iron, Austempered Ductile Iron (ADI), Compacted Graphite Iron (CGI) and high Silicon-Molybdenum (Si-Mo) Ductile Iron, Gray Iron and Steel Castings. The SAE Standards, (and draft standards), will be critically compared to those for ASTM and ISO. Salient differences in the standards will be discussed and implications to design engineers will be addressed. Comparisons to other, competitive materials (and their standards) will be made.

During the last decade, advances in magnesium die casting technology have enabled the production of large lightweight thin walled die castings that offer new approaches for low investment body construction techniques. As a result, many OEMs have expressed an interest in magnesium door closure systems due to investment reduction opportunities, coupled with potential weight savings of up to 50%. However, for such applications, product engineers are faced with the challenge of designing for stiffness and strength in crash critical applications with a material of lower modulus and ductility compared to wrought sheet product. Concept designs for side door systems have been presented in the literature, and indicate that structural performance targets can be achieved. However, to date, series production designs feature a multitude of supplementary sheet metal reinforcements, attached to die castings, to handle structural loads.