Search Results

Key on/off Vibrations plays an important role in the quality of NVH on a vehicle. Hence having a good KOKO in the vehicle is desirable by every OEM. The vibration transfer to the vehicle can be refined by either reducing the source vibrations or improving isolation. In this study, critical factors affecting KOKO vibration has been identified. Focus has been given on improving the KOKO by change in mounting system stiffness & stopper gap, and assuming other parameters as constant. The study highlights a new simulation approach using ADAMS View to help run a DOE for solving KOKO issue on vehicle. The contribution of C mount stiffness and stopper gap is shown through simulation results. The correlation between simulation & test results has been established by measuring rigid body modes and KOKO vibration on vehicle for a set of mount configuration. Test results show significant KOKO improvement with the mount configuration optimized through simulation.

If we see from the past and now competition in automotive industry increased tremendously and every car manufacturer are bringing up there innovations into the market and giving a lot of options to the customers to choose and the customer experience as well as satisfaction has become one of the main driver of success for the company. In today’s world of automotive design virtual analysis is playing a crucial role in the design and development. There are software’s that are available in market to simulate practical conditions digitally. Here we are mainly focused on effect of change in engine mount stiffness on acceleration at driver seat rail point using ADAMS. Which facilitates reduction of design of experiments and finalizing optimized stiffness values for engine mounts for engine idle vibration refinement point of view. ADAMS is mechanical system analysis software where we can simulate the dynamic behavior and distribution of loads throughout the system.

Breather assembly is mounted on transmission to maintain the pressure equilibrium inside transmission. Breather allows the transmission to breathe air when the air inside transmission expands or contracts due to heating and cooling of lubricating oil during vehicle running. Breather allows the hot air to escape and cool air to enter into the transmission to prevent overheating issue. Failure of breather assembly can lead to pressure buildup inside transmission and further leading to leakage from transmission oil seals. Oil leakage through the breather assembly is governed by parameters such as opening pressure, location and orientation of breather etc. The transmission undergoes different operating conditions of input speed, load, temperature, inclination etc. Also, breather assembly is designed and positioned in such a way that there is no leakage through breather due to oil splash inside the transmission.

Brake system is the most important system in the vehicle considering the overall vehicle safety and speed control. Brake applications are repetitive during a city traffic and hilly terrain on downhill gradient. Frequent braking gives rise to an overheating of the brake drum and its components. Braking operations at high temperature gives rise to problems like reduced deceleration due to loss of brake pad friction characteristics, pad softening and sticking to drum, pad distortion and wear etc. All these factors collectively result in deterioration of the braking performance and reduction of brake pad durability with time. Till date most of the thermal analysis performed for brake drum heating are through physical testing using brake system prototypes and by means of CFD tools. These methods are time consuming and expensive. There is a need for an alternative method to reduce physical trials and prototype building and reduce dependency on CFD analysis.

Engine mounting system maintains the position of powertrain in the vehicle with respect to chassis and other accessories during inertia, torque reaction loads and roadway disturbances. The mounting system also plays a role in terms of isolation of the rest of the vehicle and its occupants from powertrain and helps in maintaining vehicle ride and handling condition. This paper investigates the performance comparison between hydromount and switchable hydromount during idle and ride performance. The optimization scheme aims to improve the performance of the mounting system in order to achieve overall powertrain performance and NVH attribute balancing through switchable mount technology.

In case of new generation of commercial vehicles, three shaft transmissions are designed with press fitted gears on counter shaft. It allows user to save the cost of transmission manufacturing by considerable amount. In case of heavy commercial vehicles, which are being used in abusive conditions such as mining and off-road applications, it becomes absolutely necessary to ensure that the gears press fit should withstand the continuous loads and impact loads. There are design guidelines available to ensure proper fit and torque carrying capacity between the mating parts. Still, there are gear slippage, shaft and gear breakage failures in the field. In this scenario, there is a need to develop bench test procedure which will capture such failures in the prototype stage. Looking at the failures in the field, it is necessary to capture all above hidden failures in design validation phase.

NVH refinement of passenger vehicle is very much essential to level that customer did not find any irritation. Engine mounting selection and design is critical to achieve targeted NVH performance. Most of OEM’s are using properly tuned hydromount to have best idling NVH performance. Hydro-mount design should be tuned at problematic frequency where we can get the very low dynamic stiffness and can get the required performance. Hydromount should be designed carefully otherwise there will be abnormal noise due to cavitation effect. Cavitation noise is such a noise which is very difficult to identify that it is coming from mount. Cavitation is the formation and collapse of vapor bubbles in a working fluid when local static pressure falls below the vapor pressure of the working fluid. Systematic approach is presented in this paper to detect cavitation noise from hydraulic mount and how to overcome the same.

Tailgate stoppers play vital role in exerting preload on the Tailgate latch mechanism and also restrict the relative motion of the Tailgate against vehicle Body in White (BIW). These stoppers act as over-slam dampeners and reduce the transmissibility of vibrations thereby reduce the risk of Squeaks & Rattles (S&R) noises. S&R noises from Tailgate are most annoying to the rear passengers in the vehicle and are recurring in nature. Preventing these issues during design is a challenging task. S&R risk simulations enable us to conduct virtual Design of Experiments (DOEs) and arrive at optimal solutions. This approach helps in reducing the cost of the design changes that are required in the physical prototype at the later stages of product development and save time. The risk evaluation in the simulations is based on the relative displacement at the interfaces of two components.

Clutch engagement judder is a phenomenon wherein the driver experiences vibrations on seat during the clutch engagement process for the vehicle launch. Clutch engagement judder is one of the critical vehicle attributes as a part of overall vehicle NHV. Torsional oscillations, specifically originating from clutch in the driveline during clutch engagement, are referred as clutch engagement judder. Judder is a phenomenon wherein friction induced torsional vibrations are generated in the driveline because of sliding contact between clutch and flywheel, during engagement. These resulting oscillations inherit the first resonance frequency of the driveline. The engagement judder not only affects the dynamics of transmission system but also the vehicle, because of excitations being transferred to body via suspensions and mounts. Passengers experience these oscillations as vibrations during vehicle launch. If excitation level is high then it may cause discomfort to passengers.

In the recent years steering feel characteristics have emerged as one of the important brand image attributes of automotive OEMs. Since past few decades, the hydraulic assisted steering system (HPAS) on which lot of research was done to tune the steering feel has been taken over by electric power assisted steering (EPAS) system. The EPAS primarily uses an electric motor controlled by an electronic control unit to assist the driver in maneuvering the vehicle. The next big leap in the steering system advancement is steer-by-wire (SbW) technology where the mechanical linkage between the steering wheel and the road wheels is eliminated. The advantages of this system are ease to use, elimination of noise-vibration-harshness of steering system caused by road forces, modularly of steering system for packaging, improved visibility to front-end displays and road ahead and a fun to drive concept.

The fuel economy of heavy commercial vehicles can be significantly improved by reducing the rolling resistance of tires. To reduce the rolling resistance of 6×4 tractor, the super single tires instead of rear dual wheel tires are tried. Though the field trials showed a significant increase in fuel economy by using super single tires, it posed a concern of road safety when these tires blowout during operation. Physical testing of tire blowout on vehicle is very unsafe, time consuming and expensive. Hence, a full vehicle simulation of super single tire blowout is carried out. The mechanical properties of tires such as cornering stiffness, radial stiffness and rolling resistance changes during the tire blowout; this change is incorporated in simulation using series of events that apply different gains to these mechanical properties.

In today's scenario, most of the OEMs use manual transmissions with synchronizer gear shifting system for ease of gear shifting. It gives very high fuel efficiency. Gear shifting is a customer touch point, hence it is very important to select adequate synchronizer capacity so that it will perform in better and last longer. To test the synchronizers, there are many test methods which give the idea about life of synchronizer and its performance, in different conditions. Regular synchronizer rig tests consume lot of time in deriving the results. So it is very important to find out a way which will give same results within short time period. To carry out the short time test or accelerated test, we need to understand the effect of various factors like reflected inertia, drag torque, differential speed, synchronizing time, and gear shifting force on synchronizer capacity.

Structural automotive components are subjected to fatigue damage under cyclic stresses and strains. The fatigue damage initiates at stress levels lower than the elastic limit of the material and results in cracks. The Initial fatigue cracks are difficult to detect, such cracks can develop rapidly and cause sudden and brittle failure in structures. Many structural automotive components are fabricated involving weld induced local conditions such as geometry of weld toe and localized tensile residual stresses. These conditions are favorable for initiation of fatigue damage at weld toe. In current work, sever plastic deformation (SPD) which is based on high frequency impact treatment using ultrasound energy was applied on weld toe of representative weld joints. The effect of SPD on weld toe geometry modification, microstructure and residual stresses were evaluated. Microscopic and X-ray diffraction techniques were used to study the effects of SPD.

For sustainability in automobile manufacturing, recycle, reuse, and repair of used up cutting tools is now an established process. Although many types of tools were designed for one time use and then throw, an increasing awareness of the impact on the natural resources have made manufacturers to put some of these back to use or sell it back to suppliers who have put up a mechanism to extract the elements e.g. Tungsten and use it for manufacturing of new tools. There are many ways in which cutting tools can be recycled. Be it by reshaping a used up throwaway type tool [1], by redesigning of a tool holder for the use of unused cutting edges [2] or reusing short length drills that are used in making of long oil holes in crank case, cylinder head, cam shaft or connecting rods [3]. This paper demonstrates successful use of used up crankshaft grinding wheels.

A large number of metal cutting inserts are used in the manufacturing of automobile parts. These are made from hard metals like Carbide, Ceramic, Cermet, PCD and CBN. Since making of these hard metal inserts involve a high amount of energy in addition to natural resources namely Titanium, Tungsten, Cobalt etc, any attempt made therefore for reusing of the used up inserts will benefit environment because this reuse will lower down the demand on natural resource. Reuse can be done in a number of ways [ 1 ]. Many of these recycling techniques involve removing the dull portion developed during the first use by re sharpening [ 2 ]. A different approach is being suggested here in which used up inserts can be used directly. This approach leads to use of the unused cutting edges /corners of the insert without any re sharpening. Thus the cost of machining becomes half of the original cost or even more depending on the application for reuse.

Polymers are substituting traditional materials, such as metals, in existing as well as new applications, both for structural and aesthetic applications as they are lightweight, customizable and are easy to mould into complex shapes. With such an extensive use of polymers, there is a need to carefully scrutinize their performance to ensure reliability. This is particularly the case in the automotive and electronic industries where the aesthetic appeal of their products is of prime concern and any visible scratch damage is undesirable. Concern for aesthetics has led to a need for the quantification of visibility due to scratch damage on polymeric surfaces Many painted plastic parts used in vehicles are being replaced with the molded-in color plastics for cost reduction and also due to environmental concerns associated with solvent emissions. There are multiple methods used for scratch evaluation of polymers and paints.

Normal engine mounting system is designed to carry loads of powertrain in all driving conditions and also isolate the vibrations of powertrain. Softer mounts are good for vibration isolation but it is not recommended to have softer mounts because durability will be affected adversely. Optimum stiffness needs to be finalized which will have balance between durability and performance. In addition to durability many performance parameters needs to be checked during the time of development. This study includes the development of engine mounting system for elimination of drive away judder in first gear. Maximum peak torque value for the drive-away event is in the range of 80Nm - 120Nm. In the worst case, this peak torque can reach to maximum 170Nm depending on maneuver, engine rpm is around 1100-1200. Steering wheel, instrument panel and whole vehicle cabin will vibrate for few seconds and then vehicle will run smoothly.

Today’s competitive market demands for low cost passenger cars with lighter, smaller size, peppy response and fuel efficient engines and having world class NVH refinement levels. For such requirements, it is essential to optimize the product starting from the design conceptual stage, considering all performance aspects. Generally, three cylinder engines, due to less reciprocating masses, compared to four-cylinder engine, are said to be fuel efficient for the same capacity. Nevertheless, NVH problems caused by inherent imbalance forces and couples remain as drawback of the three-cylinder engine. However, through optimal design of the crank train, control of cylinder to cylinder pressure variation, stiffening of the engine structure, optimizing the integration with a vehicle through proper design of mounts, NVH refinement levels can be improved.

Twist beam is a semi-independent suspension having two trailing arms attached to the chassis via rubber bushes. Closed profile ‘V’ shaped cross beam interconnects left and right side arms. It provides roll stiffness of the suspension, by twisting as the two wheels moves relative to each other. Due to driving and road conditions twist beam structures are subjected to cyclic twist loads resulting into roll fatigue failure mode [1]. To design twist beam for mass, package and performance it is required to find realistic cross articulations based on vehicle application, usage pattern and protect twist beam from roll fatigue failure mode. The objective of this paper is to develop a virtual method using ‘ADAMS ®’ multibody dynamics software for maximum relative wheel center displacements during realistic hilly areas conditions. This paper describes half and full vehicle based virtual approach for twist beam cross articulations in hilly area conditions.

Apart from being an active safety system the brake system represents an important aspect of the vehicle dynamics. The vehicle retardation and stopping distance completely depend upon the performance of brake system and the functionality of all components. However, the performance prediction of the entire system is a challenging task especially for a complex configuration such as multi-axial vehicle applications. Furthermore, due to its complexity most often the performance prediction by some methods is limited to static condition. Hence, it is very important to have equivalent mathematical models to predict all performance parameters for a given configuration in all different conditions This paper presents the adopted system modelling approach to model all the elements of the pneumatic brake system such as dual brake valve, relay valve, quick release valve, front and rear brake actuators, foundation brake etc.