Search Results

The usage of forging a preformed, near net shape, compacted and sintered metal powder has been widely accepted since the eighties and is now one of the mainstays for producing Connecting rods in North America. However, its use in Indian subcontinent is limited as its counterpart i.e. conventional steel forging is still the most dominant. Powder metallurgy route has many advantages like good dimensional accuracy; minimum scattering of weight etc. Despite these advantages, the Powder metallurgy process is still not preferred predominantly due to technical (endurance) and infrastructural limitations. This work envisages combining the benefits of powder metallurgy process with the required mechanical properties viz. tensile and fatigue strength alongside design modifications to meet the requirements of a connecting rod for a 2-cylinder diesel engine. The connecting rods met the fatigue life at the required FOS equaling the performance of a conventionally forged connecting rod.

In today’s manual transmissions of car, gearshift system requires high performance with particular emphasis on low effort, minimal travel and positive feel. To meet these targets, a high capacity multi cone synchronizers along with higher co-efficient of friction material used for lower gears. The design of synchronizer with these specifications is influenced by torsional fluctuations from engine. Excessive torsional vibrations leads to wobbling of synchro rings within the peripheral clearances with surrounding parts. Wobbling leads to abrasion wear of frictional area of synchro ring causing grating or crashing noise of gears during shifting. This paper presents the optimization of the multiple cone synchronizer design exposed to excessive torsional vibrations and validation of the same on test bench during development stage instead vehicle level validation.

In case of new generation of commercial vehicles, three shaft transmissions are designed with press fitted gears on counter shaft. It allows user to save the cost of transmission manufacturing by considerable amount. In case of heavy commercial vehicles, which are being used in abusive conditions such as mining and off-road applications, it becomes absolutely necessary to ensure that the gears press fit should withstand the continuous loads and impact loads. There are design guidelines available to ensure proper fit and torque carrying capacity between the mating parts. Still, there are gear slippage, shaft and gear breakage failures in the field. In this scenario, there is a need to develop bench test procedure which will capture such failures in the prototype stage. Looking at the failures in the field, it is necessary to capture all above hidden failures in design validation phase.

In the recent years steering feel characteristics have emerged as one of the important brand image attributes of automotive OEMs. Since past few decades, the hydraulic assisted steering system (HPAS) on which lot of research was done to tune the steering feel has been taken over by electric power assisted steering (EPAS) system. The EPAS primarily uses an electric motor controlled by an electronic control unit to assist the driver in maneuvering the vehicle. The next big leap in the steering system advancement is steer-by-wire (SbW) technology where the mechanical linkage between the steering wheel and the road wheels is eliminated. The advantages of this system are ease to use, elimination of noise-vibration-harshness of steering system caused by road forces, modularly of steering system for packaging, improved visibility to front-end displays and road ahead and a fun to drive concept.

Design of HVAC system plays an important role in acoustic comfort for passengers. With automotive world moving towards electrical vehicles where powertrain noise is low, designing low noise HVAC system is becoming more important. For an automobile manufacturer, ability to predict the production vehicle cabin noise at the early design stage is important as it allows more freedom for design changes, which can be incorporated in the vehicle at lower cost. Although HVAC prototype and system level testing at early design stage is possible for noise estimation but flow field is not visible in test that makes difficult to improve design. CFD simulation can provide detailed information on flow field, noise source strength and location. But in such a simulation, accurate prediction has been a challenge due to the inability of CFD tools to model acoustic absorptive characteristics of interior walls of cabin.

Structural automotive components are subjected to fatigue damage under cyclic stresses and strains. The fatigue damage initiates at stress levels lower than the elastic limit of the material and results in cracks. The Initial fatigue cracks are difficult to detect, such cracks can develop rapidly and cause sudden and brittle failure in structures. Many structural automotive components are fabricated involving weld induced local conditions such as geometry of weld toe and localized tensile residual stresses. These conditions are favorable for initiation of fatigue damage at weld toe. In current work, sever plastic deformation (SPD) which is based on high frequency impact treatment using ultrasound energy was applied on weld toe of representative weld joints. The effect of SPD on weld toe geometry modification, microstructure and residual stresses were evaluated. Microscopic and X-ray diffraction techniques were used to study the effects of SPD.

For sustainability in automobile manufacturing, recycle, reuse, and repair of used up cutting tools is now an established process. Although many types of tools were designed for one time use and then throw, an increasing awareness of the impact on the natural resources have made manufacturers to put some of these back to use or sell it back to suppliers who have put up a mechanism to extract the elements e.g. Tungsten and use it for manufacturing of new tools. There are many ways in which cutting tools can be recycled. Be it by reshaping a used up throwaway type tool [1], by redesigning of a tool holder for the use of unused cutting edges [2] or reusing short length drills that are used in making of long oil holes in crank case, cylinder head, cam shaft or connecting rods [3]. This paper demonstrates successful use of used up crankshaft grinding wheels.

Vehicle crashworthiness is an important aspect of vehicle development. Vehicle structural performance plays a critical role during crash for controlling the occupant injuries. During a crash event, vehicle energy management governs the structural performance and passenger compartment integrity. However, these parameters are dependent on material properties such as yield/ultimate tensile strength, work hardening effects, strain rate dependency, material elongations and material fracture strains. Appropriate representation of these material properties in CAE (Computer Aided Engineering) environment is very critical for reliable prediction of vehicle structural performance during development phase. Among all material properties, material fracture strain is the most complex one and needs detailed material characterization approach for failure definitions.

Due to the recent trend in auto industry to opt for higher power engines, causes increase in vibrations levels in the passenger’s compartment. This requires a better and comprehensive model to analyze vibrations from engine to seat and steering wheel much before the proto stage of development in the design stage itself. For this purpose, modelling is done in ADAMS multi dynamics and assuming the 16 degrees of freedom of the vehicle. Further, a crank drive model is developed to simulate engine excitation forces comprising unbalanced inertia forces and torque fluctuations and their effects seat rail and steering wheel vibration is derived. This tool is an attempt to predict such vibrations caused and assist in design enhancement and streamline the procedure.

Comfortable cabin environment from temperature, noise and vibration point of view is one of the most desirable aspects of any vehicle operating in hot or cold environment. Noise generated from HVAC system is one of the most irritating phenomena resulting in customer dissatisfaction and complaints. It becomes absolutely necessary to have low HVAC noise levels when the target market has hot weather all round the year. Balance between control of temperature in desired way with least possible noise and vibration is the key for HVAC performance optimization within constrains posed by design and cost. This paper describes the approach for NVH refinement of front HVAC system proposed for a vehicle with limited off-road capability for which packaging constraints and late changes related to airflow and HVAC unit design for meeting comfort and crash requirements resulted in deterioration of noise and vibrations while operation.

Normal engine mounting system is designed to carry loads of powertrain in all driving conditions and also isolate the vibrations of powertrain. Softer mounts are good for vibration isolation but it is not recommended to have softer mounts because durability will be affected adversely. Optimum stiffness needs to be finalized which will have balance between durability and performance. In addition to durability many performance parameters needs to be checked during the time of development. This study includes the development of engine mounting system for elimination of drive away judder in first gear. Maximum peak torque value for the drive-away event is in the range of 80Nm - 120Nm. In the worst case, this peak torque can reach to maximum 170Nm depending on maneuver, engine rpm is around 1100-1200. Steering wheel, instrument panel and whole vehicle cabin will vibrate for few seconds and then vehicle will run smoothly.

This paper discusses the test setup and methodology required to validate complete lift axle assembly for simulating the real time test track data. The correlation of rig vs track is discussed. The approach for reduction of validation time by eliminating few of the non-damaging tracks/events, its correlation with real life condition is discussed, and details are presented. With increased competition, vehicle development time has reduced drastically in recent past. Bench test procedure using accelerated test cycle discussed in this paper will help to reduce development time and cost. Process briefed in this paper can also be used for similar test specification for other structural parts or complete suspension system of heavy commercial vehicles.

Twist-beam suspensions are an example of design solution presenting acceptable performance when applied to passenger cars & light vehicles and it can provide an optimal between cost & performance in the automotive market. For these reasons, twist beam is quite popular in use in rear suspension of light vehicles. In contrary to other types of suspension, the twist-beam has a flexible torsion beam connecting the swing arms. The study of the deformation of this flexible element becomes important to understand its performance and durability behavior. As the name signifies, twist beam major performance attribute is control of twist or opposite wheel travel arising from vehicle roll or road input. Current approach for the study this deformation is through FEA & Multi-body dynamics software tools.

With increased awareness about environmental issues, the trend of automobile industry is to use ‘Recycled’ or ‘Biodegradable’ or ‘Energy Recoverable’ material. As a part of this programme, to make the vehicle ‘Green’ in nature, many automobile OEMs have taken the initiative to make use of natural fibre composite in their vehicles. Natural fibre based composite has been successfully proven for less critical as well as for semi-structural applications in an automobile. These typical applications are insulations, headlining, carpets, door pad etc. There is a demanding task for automotive OEMs to meet 85% Recyclability and 95% Recoverability targets by year 2015. To meet the RRR (Reuse, Recycle & Recover) and the ELV (End of Life) regulatory requirements, increased use of natural fibre based composite/ biopolymers is unavoidable. Natural fibre can offer potential advantages such as weight saving and improve overall green rating of the vehicle.

Currently, automotive industries are using Advanced High-Strength Steels (AHSS) sheet grades to achieve key requirements like light weighting and improved crash performance. But forming of AHSS grades becomes key challenge due to its lesser ductility and edge fracturing tendency during forming. In general, most of the automotive components undergoes shearing operations like blanking and punching which affects the edge ductility of the steel. AHSS grades possess limited edge ductility compared with conventional steel grades which results in edge fracturing due to tensile strain during stretch flanging operation. Stretch flange-ability is an important formability characteristic, which aids in material selection to avoid edge fracturing of complex shaped parts. Material with better stretch flange-ability possess better edge ductility and hence perform better in stretch flanging of sheet metal.

OEMs are seeking to develop vehicle light weighting strategies that will allow them to meet weight and fuel economy targets hence increasingly shifting their focus towards incorporating lighter material solutions at mass produced scales. Composites are seen by automotive manufacturers as the solution to lightweight vehicles without affecting their performance. More and more parts are made of short fiber reinforced plastics (SFRP) as well as continuous fiber composites. However, replacing metals by composites requires a new design approach and a clear understanding of the composite behavior. This paradigm however requires a dedicated tool for composite design in order to take into account the specific composite behavior. Traditional design tools are not able to state accurately the composite material behavior and sometime leading to use high safety of factors and lack of confidence in the design.

With the advent of new technologies and rigorous research and development work going on vehicle engines, cars are becoming quieter and more refined than ever before. This has led to the observance of subjective noises being audible to passenger compartment which were earlier masked behind engine noise. The vehicle HVAC system has several moving parts and transient flow of refrigerant which can cause certain types of irritant noise. Thus having a refinement in of air-conditioning (AC) system would aid us in cutting down on this parasitic noise source. Thus noise refinement should be one of the important parameters during the design and development of the Heating, Ventilation and Air-Conditioning (HVAC) system for a vehicle program.

The main objective of the exhaust system is to offer a leakage proof, noise proof, safe route for exhaust gases from engine to tailpipe, where they are released into the environment, while also processing them to meet the emission norms. New stringent emission norms demand ‘near-zero’ leakage exhaust systems, throughout vehicle life bringing the joints into focus as they are highly susceptible to leakage. Needless to say, this necessitates them to endure not only structural but also the environmental loads, throughout their life. Thus, the fatigue life or durability tests become the most critical part of the exhaust system development. Test acceleration and result correlation (for life prediction), to meet the stringent project timelines and stricter environmental norms are the key considerations for developing a new testing methodology. Quality of accelerated tests is ensured by deploying all possible multiple loads, to simulate real-life conditions.

The commercial vehicle market in India is shifting to higher payload capacity vehicles due to a lower transportation cost per unit goods. To cater this requirement, the vehicle manufacturers are designing the heavy multi-axle commercial vehicles and with higher per axle loading capacity. One of such a vehicle design involves five-axle vehicle with non-steerable, twin tire, lift axle. Though using a twin tires have increased loading capacity of lift axle compared to a single tire self-steerable lift axle, it can cause tire scrub while vehicle is turning and leads to a significant tire wear. The tire wear possibility due to use of non-steerable lift axle is estimated through simulation using full vehicle model in ADAMS. The operating zone of the vehicle, where maximum tire wear can occur, is identified through simulation. Different alternatives to reduce tire wear for this scenario are also discussed.

This paper takes a review of fretting phenomenon on splines of the engaging gears and corresponding splines on shaft of automotive transmission and how it leads to failure of other components in the gearbox. Fretting is a special wear process which occurs at the contact area of two mating metal surfaces when subject to minute relative oscillating motion under vibration. In automotive gearbox, which is subjected to torsional vibrations of the powertrain, the splines of engaging gears and corresponding shaft may experience fretting, especially when the subject gear pair is not engaged. The wear debris formed under fretting process when oxidizes becomes very hard and more abrasive than base metal. These oxidized wear particles when comes in mesh contact with nearby components like bearings, gears etc. may damage these parts during operation and eventually lead to failure.