Search Results

As the vehicle functions are getting distributed over multiple ECUs in order to realize various complex control functions, the need for sophisticated on-board diagnostic strategies are increasing in automotive domain, leading to a significant amount of hardware and software implementations for fault management inside various ECUs in the vehicle. This paper proposes optimized vehicle level approach for fault management strategies, wherein a centralized intelligent Gateway Module is proposed in the vehicle network architecture, which will be responsible for fault management of the complete vehicle in a chronological sequence. This Gateway Module will thereby have the possibility to group a cluster of faults raised by different ECUs and correlate them meaningfully to guide the operator towards root cause of the fault.

The use of Wheel Force Transducers (WFTs) to acquire data for laboratory simulation is becoming standard industry practice. However, in test rigs where we have only the suspension module and not the complete vehicle, does the reproduction of the orthogonal forces and moments at the wheel centre guarantee an accurate replication of the fatigue damage in the suspension components? The objective of this paper is to review the simulation methodology for a highly non-linear suspension in a 3 DOF (degree-of-freedom) suspension test rig in which the simulation was carried out using only the three orthogonal loads and vertical displacement. The damage at critical locations in the suspension is compared with that on the road and an assessment of the simulation using the WFT is made based on a comparison of the damage on the road vs. the rig.

Spot welding is the primary joining method used in automobiles. Spot-weld plays a major role to maintain vehicle structural integrity during impact tests. Robust spot weld failure definitions is critical for accurate predictions of structural performance in safety simulations. Spot welds have a complex metallurgical structure, mainly consisting of fusion and heat affected zones. For accurate material property definitions in simulation models, huge number of inputs from test data is required. Multiple tests, using different spot weld joinery configurations, have to be conducted. In order to accurately represent the spot-weld behavior in CAE, detailed modeling is required using fine mesh. The current challenge in spot-weld failure assessment is developing a methodology having a better trade-off between prediction accuracy, testing efforts and computation time. In view of the above, cohesive zone models have been found to be very effective and accurate.

1 With increasing fuel price, the power train size is on a downward trend. For Fuel Economy maximization, the engine capacity and reduction ratios are getting reduced. So gradability of a vehicle is becoming a trade off factor for the power train size finalization in a car. At the same time OEMs are working hard to maintain profitability by reducing development and operational cost and time. In this complexly competitive scenario in automobile manufacturing, simulation is gaining an upper hand over actual testing as simulation consumes lesser time and resource as compared to actual testing. This paper is aimed at developing a simulation technique for restart or stop and start gradability which is a very critical parameter for finalization of engine torque characteristics and power train configuration. The simulation is done on AVL-CRUISE software.

The power output of an internal combustion engine is directly proportional to the amount of air that can be forced into the cylinder per cycle and the amount of fuel that can be burned efficiently. The amount of air is most effectively increased by means of a mechanical supercharger. The purpose of this paper is attempting the non mechanical supercharging ways (Supercharging by means of gas dynamic effects) for naturally aspirated (NA) diesel engines and understanding in a better way the induction gas dynamics and its influence on engine performance characteristics. Wave dynamics in the intake system has strong influence on the performance of naturally aspirated internal combustion (IC) engines. This paper presents an application of Helmholtz resonator in the induction system of the naturally aspirated diesel engine to improve the engine breathing efficiency (volumetric efficiency).

In the automotive industry, silicon adhesive has become increasingly popular due to its benefits in ease of assembly and cost savings associated with material and manufacturing processes. To meet the imperative of minimizing both time and expenses during the project's development phase, it becomes essential to select the appropriate gasket material and an optimal flange design at the outset of the design process. In order to achieve stringent emission standards such as Real Driving Emission (RDE) and Corporate Average Fuel Economy (CAFE) norms, a better sealing performance is an essential parameter. Various types of liquid gaskets such as silicon rubber based Room Temperature Vulcanizing (RTV) sealants and thermoset plastic based Anaerobic sealants are widely used in an Internal Combustion engine. They are commonly used for the components such as oil sump, bedplate, and gearbox housings, etc.

Shock tube is used to simulate blast loading conditions on materials for studying the failure behavior of different materials under blast pressures on smaller scale. This paper describes CAE method developed for simulating shock tube experiment in LS-DYNA3D environment. The objective of shock tube simulation is to characterize material failure parameters so as to predict risk of material failure in full vehicle blast simulations while developing vehicle for blast protection applications. The paper describes modeling of shock wave and its interaction with test specimen in shock tube environment. Arbitrary Lagrangian-Eulerian (ALE) techniques are applied to simulate shock tube experiment in LS-DYNA3D and simulation predictions are compared with experimental test data. CAE correlation studies were carried out with respect to incident and reflected pressures in shock tube, deformation and plastic strains on test specimen, shock wave velocity etc.

High strength aluminium alloys are an ideal material in the automotive sector leading to a significant weight reduction and enhancement in product safety. In recent past extensive development in the field of high strength steel and aluminium was undertaken. This development has been propelled due to demand for light weight automotive parts. The high strength to weight ratio possessed by Al alloy helps in reducing the total weight of the vehicle without effecting the overall performance, thereby increasing the fuel economy, and reducing the carbon emission level. Joining of high strength aluminium alloy is critical to develop durable automotive products. Joining of high strength aluminium alloy for mass production in automobile industry is a challenging task. Laser welding is recognized as an advanced process to join materials with a laser beam of high-power, high- energy density.

Commercial vehicle are exposed to harsh environment conditions like dust, mud, wind, rain, extreme sun and winter throughout. Apart from white goods and other conventional loading these vehicles also used in applications which involve Handling of Dirty Loads, Construction Raw materials, Mining Industry etc. which leads to fast deterioration of Interiors. Also, in most cases drivers are not the owners. Hence due to high cost of Cleaning at dealerships and low Product maintenance awareness amongst Commercial Vehicle Users, on Road Washing & Cleaning by riverside is common practice which leads to early deterioration of Interior trims. This paper deals with the retention of newness of soft trim parts such as headliner, wall trims and carpets. Causes of product deterioration and attributes which influence newness like product appeal, NVH, perceived quality, environmental impact, geometry retention over time etc. have been discussed in detail.

Regenerative braking has become one of the major features for a hybrid vehicle as it converts brake energy into electrical energy storable into battery and leads to an increase in overall fuel efficiency of the vehicle. Traditional regenerative braking systems are designed such that the mechanical braking force from the friction brakes is varied in order to get maximum electric braking. This is the optimum method; however, such a system calls from electronics (Anti-lock Braking System) for regulation of mechanical braking leading to an increased cost. In this paper, the authors present a new strategy for implementing a regenerative brake strategy without changing the mechanical brake system of a conventional vehicle converted to a hybrid vehicle. The electric motor that serves as the traction motor or the Integrated Starter Generator (ISG) system, is used for regenerative braking also. There is no change in the other vehicle specifications as compared to the conventional vehicle.

Most of the energy consumed in today's mobility industry is derived from fossil fuels. The demand for clean, renewable and affordable alternative energy is forcing the automotive industry to look beyond the conventional fossil fuels. Fuels options like liquefied petroleum gas (LPG), compressed natural gas (CNG) and ethanol blends are quickly finding widespread acceptance as alternative sources. This paper presents the results of experimental studies conducted on a 1.2-liter MPI engine with three different alternate fuels. The fuels considered for the evaluation (apart from base gasoline) are 10% ethanol-blended fuel (E10), LPG (gaseous propane: butane mix) and CNG (gaseous methane). Experiments were conducted to compare their effect on engine performance and emissions. The test results show that E10 has the lowest power drop whereas CNG has the highest power drop (12%) as compared to gasoline. The maximum power drop in LPG is 4%, which is close to the theoretical predictions.

Depletion of fossil fuel reserves, the unsteadiness of their prices and the increasingly stricter exhaust emission legislation put forward attention of world towards use of alternate fuels. The ever increasing demand for ecologically friendly vehicles can be met by use of clean fuels like Compressed Natural Gas (CNG) and Hydrogen (H2). Lower carbon to hydrogen ratio of CNG makes it a cleaner fuel, due to this CNG is gaining popularity as an internal combustion (IC) engine fuel in transport sector. Hydrogen fuel for IC engines is also being considered as a future fuel due to its simple carbon less structure. However, several obstacles have to be overcome before widespread utilization of hydrogen as an IC engine fuel can occur in the transport sector. The 18 percent hydrogen enriched CNG fuel referred to as HCNG has the potential to lower emissions and could be considered a first step towards promotion of a Hydrogen economy.

In a heavy commercial vehicle, the engine cooling package is designed by considering peak heat load on the vehicle cooling system from an engine end. In cooling systems, the major unit that consumes most power from the engine is the engine cooling fan. It was seen from the vehicle measured duty cycle data, for most of the time engine operates at part load condition. Regardless of demand from the engine cooling system, engine fan was operating continuously at equivalent speed of the engine. This results in continuous consumption of productive engine power from the fan end ultimately affecting vehicle fuel economy. The present study shows that low idle speed viscous fan has the potential to meet stringent engine cooling performance requirements and consumes less engine power throughout an actual vehicle duty cycle. Experiments were conducted on test vehicle with different fan speeds.

Gasoline engines with Multi point fuel injection (MPFI) technology are being developed with naturally aspirated and/or turbocharged engines. Wherein a MPFI and turbo charged combination engines have certain challenges during development stages. One of the important challenge is design of air intake and exhaust system. With MPFI turbocharged engine combination, the under bonnet heat management is crucial task for drivability. The heat management of air intake plays a vital role in drivability part therefore a design layout of air intake path is an important aspect. Drivability can be categorized as low end, mid-range and top end drivability. Turbocharged MPFI engines have a typical phenomenon of ‘Lag in response’ in the low-end region. This ‘Lag in response’ phenomenon at low-end drivability region can be overcome through optimization of air intake system and optimization of exhaust back pressure.

Petroleum Oil, Lubricants (POL) & Liquefied petroleum gas (LPG) tanker vehicles are special application segment that holds a significant Market share for commercial vehicles. These vehicles need to comply additional Safety regulations specified by Petroleum and explosives safety organization (PESO). For compliance to Rule-70, Protective heat shield on exhaust system needs to be designed and validated in order to avoid any catastrophic failure. The paper demonstrates the methodology to identify the worst case scenario for the existing commercial vehicle segment. Based on detail digital mock up (DMU) review Metallic heat shield was designed on after treatment system (ATS). The flexible heat shield was designed for exhaust pipe & joints in order to restrain the heat flow to the surrounding aggregates. After finalising design, CFD analysis was carried out to find out the thermal effects on various components and results within acceptable limits.

Important vehicle performance parameters such as, fuel economy and high speed stability are directly influenced by its aerodynamic drag and lift. Wind tunnel testing to asses these parameters requires heavy investment especially when test wind tunnel is not available in the country where vehicle development center is present. Hence to save cost and to compress development time, it is essential to asses and optimize parameters of a vehicle in very early stages of development. Using numerical flow simulations optimization runs can be carried out digitally. Industry demands prediction of aerodynamic drag and lift coefficients (CD,CL) within an accuracy of a few counts, consuming minimal HPC resources and in a short turnaround time. Different OEMs deploy different testing methods and different softwares for numerical simulations.

A hybrid electric powertrain being a complex system requires analysis of all its subsystems to optimally utilize, size components for performance evaluation and control strategy development. An integrated high fidelity model of these can lower development costs, time and achieve the targeted performance while allowing for early redefinition of the system. A high fidelity model of a sedan car featuring chassis with longitudinal and lateral dynamics, suspension with joints, tires calculating longitudinal & lateral forces during vehicle motion, Engine model with combustion & dynamics of reciprocating and rotating components, Electric motors, Battery system, and gearbox with synchronizers and friction components was developed. Powertrain components were interconnected using 3D rotational flanges. Weight distribution was accomplished by appropriately locating various powertrain components using 3D supporting mounts, which help to study the mount forces as well.

One of the very first customer touchpoint in a vehicle is quality of gear shifting. Gearshift quality is perceived as a symbol of refinement of a vehicle. Globally, lot of efforts are taken to refine the gearshift quality. Design improvements in internal components of transmission, cable and shifter assembly, knob design iterations are carried out to arrive at optimum gearshift quality at the vehicle level. Current practice for this activity includes processes such as design modification, manufacturing of proto components, assembly of components and fitment in the vehicle. This vehicle is then instrumented with sensors and data acquisition units to capture the parameters which determine the gearshift quality. This is an iterative process which goes on until necessary refinement/improvement is achieved. This process requires investment of lot of time, efforts and the budget. This paper describes a virtual approach to arrive at optimum design of components.

Passive safety regulations specify minimum safety performance requirements of vehicle in terms of protecting its occupants and other road users in accident scenarios. Currently for majority cases, the compliance of vehicle design to passive safety regulations is assessed through physical testing. With increased number of products and more comprehensive passive safety requirements, the complexity of certification is getting challenged due to high cost involved in prototype parts and the market pressures for early product introduction through reduced product development timelines. One of the ways for addressing this challenge is to promote CAE based certification of vehicle designs for regulatory compliance. Since accuracy of CAE predictions have improved over a period of time, such an approach is accepted for few regulations like ECE-R 66/01, AIS069 etc which involves only loadings of the structures.

Liquefied Petroleum Gas (LPG)-powered vehicles use a pressure regulator/vaporizer to expand and modulate the gas pressure to meet the engine's operational demands. This expansion process is accompanied by a phase change wherein liquid LPG is converted to its gaseous form. This consequently reduces the temperature of the working fluid which may result in freezing (Joule-Thompson effect). In order to aid complete phase change and avoid any freezing, the vaporizer is heated either electrically or by the engine coolant circulation. Any inefficiency in the heating may lead to improper phase change and can result in a phenomenon known as "liquid carryover," wherein a liquid LPG gets entrained in the downstream gas circuit where the gaseous form is demanded. The liquid carryover (if any) leads to the improper engine functioning leading to driveability and emission issues.