Search Results

Further improvements of internal combustion engines to reduce fuel consumption and to face future legislation constraints are strictly related to the study of mixture formation. The reason for that is the desire to supply the engine with homogeneous charge, towards the direction of a global stoichiometric blend in the combustion chamber. Fuel evaporation and thus mixture quality mostly depend on injector atomization features and charge motion within the cylinder. 3D-CFD simulations offer great potential to study not only injector atomization quality but also the evaporation behavior. Nevertheless coupling optical measurements and simulations for injector analysis is an open discussion because of the large number of influencing parameters and interactions affecting the fuel injection’s reproducibility. For this purpose, detailed numerical investigations are used to describe the injection phenomena.

Engine valve flow coefficients are not only used to characterize the performance of valve/port designs, but also for modelling gas exchange in 0D/1D engine simulation. Flow coefficients are usually estimated with small pressure ratios and at ambient air conditions. In contrast, the ranges for pressure ratio, pressure and temperature level during engine operation are much more extensive. In this work the influences of these three parameters on SI engine poppet valve flow coefficients are investigated using 3D CFD and measurements for validation. While former investigations already showed some pressure ratio dependencies by measurement, here the use of 3D CFD allows a more comprehensive analysis and a deeper understanding of the relevant effects. At first, typical ranges for the three mentioned parameters during engine operation are presented.

Engine valve flow coefficients are used to describe the flow throughput performance of engine valve/port designs, and to model gas exchange in 0D/1D engine simulation. Valve flow coefficients are normally determined at a stationary flow test bench, separately for intake and exhaust side, in the absence of the piston. However, engine operation differs from this setup; i. a. the piston might interact with valve flow around scavenging top dead center, and instead of steady boundary conditions, valve flow is nearly always subjected to pressure pulsations, due to pressure wave reflections within the gas exchange ports. In this work the influences of piston position and flow pulsation on valve flow coefficients are investigated for different SI engine geometries by means of 3D CFD and measurements at an enhanced flow test bench.

A simulation approach to predict the amount of snow which is penetrating into the air filter of the vehicle’s engine is important for the automotive industry. The objective of our work was to predict the snow ingress based on an Eulerian/Lagrangian approach within a commercial CFD-software and to compare the simulation results to measurements in order to confirm our simulation approach. An additional objective was to use the simulation approach to improve the air intake system of an automobile. The measurements were performed on two test sites. On the one hand we made measurements on a natural test area in Sweden to reproduce real driving scenarios and thereby confirm our simulation approach. On the other hand the simulation results of the improved air intake system were compared to measurements, which were carried out in a climatic wind tunnel in Stuttgart.

Urban air mobility (UAM) is a fast-growing industry that utilizes electric vertical take-off and landing (eVTOL) technologies to operate in densely populated urban areas with limited space. However, atmospheric icing serves as a limitation to its operational envelope as in-flight icing can happen all year round anywhere around the globe. Since icing in smaller aviation systems is still an emerging topic, there is a necessity to study icing of eVTOL rotors specifically. Two rotor geometries were chosen for this study. A small 15-inch rotor was selected to illustrate a multirotor UAV drone, while a large 80-inch rotor was chosen to represent a UAM passenger aircraft. The ice accretion experiments were conducted in an icing wind tunnel on the small 15-inch rotor. The icing simulations were performed using FENSAP-ICE. The ice accretion simulations of the 15-inch rotor sections at –5 °C show a large, rather streamlined ice shape instead of the expected glaze ice characteristics.

Quantitative Laser-Induced Incandescence (LII) has been applied to investigate the soot formation in a combusting Diesel jet for various conditions. For the quantification of the LII signal the local soot volume fraction of a diffusion flame burner was measured using laser beam extinction. These data were used for the calibration of the LII signal. The investigation of the soot formation in a combusting Diesel jet was performed in a high pressure, high temperature combustion chamber with optical access. A wide range of pressure (up to 10 MPa) and temperature (up to 1,500 K) conditions could be covered using a hydrogen precombustion, which is initiated inside the chamber before fuel injection. The influence of different gas atmospheres have been investigated by varying the gas composition (H2, O2 and N2) inside the chamber.

Modern automotive development evolves beyond artificial intelligence for highly automated driving, and toward an interconnected manifold of data-driven development processes. Widely used analytical system modelling struggles with rising system complexity, invoking approaches through data-driven system models. We consider these as key enablers for further improvements in accuracy and development efficiency. However, literature and industry have yet to thoroughly discuss the relevance and methods along the vehicle development cycle. We emphasize the importance of data-driven system models in their distinct types and applications along the developing process, from pre-development to fleet operation. Data-driven models have proven in other works to be fast approximators, of high accuracy and adaptive, in contrast to physics-based analytical approaches across domains.

A numerical method for generating a blockloading profile from a rainflow histogram is described. Unlike previous techniques, this method produces a blockloading profile which, when rainflow-counted, yields a rainflow histogram identical to the original. When implemented with modern data acquisition and signal-processing techniques, this generation method provides a means of developing blockloading test profiles which are correlated with actual service data. This key benefit elevates existing simple testing systems as useful and productive tools despite the emrgence of more complex testing systems.

Product development processes generate large quantities of experimental and analytical data. The data evaluation process is usually quite lengthy since the data needs to be extracted from a large number of individual output files and arranged in suitable formats before they can be compared. When the data quantity grows extremely large, manual extraction cannot be done in a limited timeframe. This paper describes a set of tools developed by MTS engineers to automatically extract the desired information from a large number of files and perform data post-processing. The tools greatly improved both speed and accuracy of the evaluation process during the development of a sound quality-based end-of-line inspection system for seat tracks [1]. It allowed engineers to quickly gather a comprehensive understanding of the relative importance of individual design parameters and of their correlation to the subjective perception of the sound quality of the seat track.

In recent studies, the health implications of ultra fine particle emissions from vehicles have been investigated in a number of international studies. The adverse health effects are not only dependent on total particulate mass but also on other attributes including size, number and surface area of the particles. These ultra fine particles cause more adverse effect than larger particles. With this need UNECE GRPE had launched a Particulate Measurement Program (PMP) to formulate the regulation to control both particulate mass and number of ultra fine particles. These new regulations are applicable to the diesel and gasoline direct injection passenger cars and heavy duty engines of Euro-V/VI technology. However, at present the other vehicle categories and alternate fuels are not been covered. Limited experiments have been carried-out on the in-use vehicles which are with old technologies.

A numerical simulation program for the design of the cooling air duct and the cooling system of vehicles for stationary operating conditions is introduced. This program allows the simulation of interactions with the system environment resp. an air conditioning. Hot recirculations of air in the front part of the car and the inhomogenious flow through the heat exchangers radiator and condensor in their affects on the heat transfer capacity are simulated. The power demand of the fan, the water pump and the compressor is taken into account for calculating the heat flow from the engine into the cooling water.

Today, LRI is a proven manufacturing technology for both small and large scale structures (e.g. sailboats) where, in most cases, experience and limited prototype experimentation is sufficient to get a satisfactory design. However, large scale aerospace (and other) structures require reproducible, high quality, defect free parts, with excellent mechanical performance. This requires precise control and knowledge of the preforming (draping and manufacture of the composite fabric preforms), their assembly and the resin infusion. The INFUCOMP project is a multi-disciplinary research project to develop necessary Computer Aided Engineering (CAE) tools for all stages of the LRI manufacturing process. An ambitious set of developments have been undertaken that build on existing capabilities of leading drape and infusion simulation codes available today. Currently the codes are only accurate for simple drape problems and infusion analysis of RTM parts using matched metal molds.

Environmental pollution is of great concern; hence the emission norms for the diesel engines are made more stringent. The purpose of this work is to develop a process to optimize the FIS parameters and select a most suitable FIS by simulation to meet the target emissions. During the combustion optimization exercise of diesel engine, different hardware combinations like injector, HPP etc are matched through testing to achieve the required performance and emissions. The process requires the real testing of the engine on engine dynamometer with various hardware combinations, which is expensive and time consuming. A simulation model of diesel FIS is constructed using ‘AVL Hydsim’. The model is validated by comparing the predicted and the experimental results. The validated model is used for further work. Critical parameters were listed based on the sensitivity analysis on the base model.

Anthropometric data of a country is vital database for automotive design and other design applications. It is also an important parameter in population studies. Most developed countries have invested resources over the years to develop such a database and this information is accessed by many OEMs and major Design Houses. However, an updated and comprehensive Anthropometry of Indian Population is largely unknown. In the past, a few institutions have done projects to bring out a picture of the Indian Anthropometry. However, keeping in view the rapid industrialization and increase of India-specific designs which require an access to latest Anthropometric database, the project “SIZE INDIA” has been initiated. For the first time in India, a state of the art 3D Whole body scanner technology has been used and thereby large volume of data has been generated in a very short span of time.

A real-time 3-dimensional, nonlinear simulator for the dynamical behaviour of trucks has been developed. The simulator serves as industrial test stand for examinations on different electronic control systems. This paper describes the challenging task of developing a powerful real-time simulator with hardware coupling based on parallel transputer systems. The integration of an anti-lock braking system (ABS) as hardware-in-the-loop by means of an interface electronic device is described. The interface electronics provide the coupling of the electronic control unit (ECU). The special demands on the signals and the resulting concept for the developed electronic interface are specified. Some results from dynamic braking simulations show the quality of the simulator.

Multi-dimensional modelling of the flow and combustion promises to become a useful optimisation tool for IC engine design. Currently, the total simulation time for an engine cycle is measured in weeks to months, thus preventing the routine use of CFD in the design process. Here, we shall describe three tools aimed at reducing the simulation time to less than a week. The rapid template-based mesher produces the computational mesh within 1-2 days. The parallel flow solver STAR-CD performs the flow simulation on a similar time-scale. The package is completed with COVISEMP, a parallel post-processor which allows real-time interaction with the data.

Recently, the use of laboratory-based physical prototype testing as well as the design of virtual models and virtual test equipment has accelerated the pace and quality of racing vehicle development. In particular, the combined use of both virtual and physical testing, when correlated to racetrack improvements, yields a powerful development tool(1), (2),(3). In this study, we applied these techniques from the first stages of the design of a unique Grand Prix racing motorcycle. First, a wire-frame CAD model, then a parametric CAD solid model of the motorcycle was created after preliminary calculations specified the approximate design of structural elements. Subsequently, a virtual dynamic model was created and subjected to a variety of inputs, including sine sweeps, shaped white noise and simulated road time-histories. Loads and other dynamic responses were measured on the virtual model, so that it's design could then be optimized to yield acceptable performance and durability.

A two-dimensional technique for the quantitative determination of the fuel-air ratio in hydrogen fuelled engines has been developed. The technique is based on the spontaneous Raman scattering of the hydrogen molecules (Stokes Q-branch) and the simultaneous measurement of the pressure inside the combustion chamber. From these data the local partial pressure of the hydrogen and, therefore, the fuel-air ratio can be calculated. This method was applied in a single cylinder direct injection research engine in order to prove the applicability of this technique under real engine conditions. The measurements inside the side chamber of the engine show a fast mixing process of the compressed air and the injected hydrogen (6 MPa injection pressure) independent of the injection timing.

In this paper the effects of pulsating blankholder forces in deep draw processes for sheet metal parts are discussed. Areas with and without tangential compressive stresses in the flanges, which are located between the binders, are discussed separately. Areas without tangential compressive stresses can be simulated by a special friction strip-draw test using a pulsating normal force ( representing the blankholder force ). Investigations using this equipment show that by pulsating blankholder forces it is possible to avoid galling and to reduce the friction force. Areas with tangential compressive stresses can be simulated by deep drawing axissymmetric cups using a pulsating blankholder force. Investigations with this equipment show that without increasing the danger of wrinkling the friction forces can be reduced by pulsating blankholder forces, when a certain frequency limit is reached.

For integrating Life Cycle Assessment into the design process it is more and more necessary to generate models of single life cycle steps respectively manufacturing processes. For that reason it is indispensable to develop parametric processes. With such disposed processes the aim could only be to provide a tool where parametric environmental process models are available for a designer. With such a tool and the included models a designer will have the possibility to make an estimation of the probable energy consumption and needed additive materials for the applied manufacturing technology. Likewise if he has from the technical point of view the opportunity, he can shift the applied joining technology in the design phase by changing for instance the design.