Search Results

Life Cycle Assessment (LCA) is a methodology used to determine quantitatively the environmental impacts of a range of options. The environmental community has used LCA to study all of the impacts of a product over its life cycle. This analysis can help to prevent instances where a greater degree of environmental harm results when changes are made to products based on consideration of impacts in only part of the life cycle. This study applies the methodology to engine lubricants, and in particular chlorine limits in engine lubricant specifications. Concern that chlorine in lubricants might contribute to emissions from vehicle exhausts of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), collectively called PCDD/F, led to the introduction of chlorine limits in lubricant specifications. No direct evidence was available linking chlorine in lubricants to PCDD/F formation, but precautionary principles were used to set lubricant chlorine limits.

The Nissan KA24E engine test is designated to replace the Ford Sequence VE engine test as the low temperature valve train wear requirement for ILSAC (International Lubricant Standardization and Approval Committee) GF-3. The KA24E (recently designated the Sequence IV A) represents much of the current world-wide material and design technology while retaining the sliding cam/follower contact found in earlier engine designs. The work presented here is the first of two reports. In this first report, the physical and chemical environment the KA24E engine presents a lubricant is characterized and compared to those of the Sequence VE engine. Valve train materials and wear modes are investigated and described. Although chemical analysis of drain oils indicate the KA24E procedure does not degrade the lubricant to the extent seen in the Sequence VE test, valve train wear appears to proceed in a similar manner in both tests.

SAE 2004-01-3009 reported on work conducted to investigate the correlation between the Mack T-11 laboratory engine tests and vehicle field tests. It concluded that the T-11 test provides an effective screening tool to investigate soot-related viscosity increase, and the severity of the engine test limits provides a substantial margin of safety compared to the field. This follow-up paper continues the studies on the 2003 Mack CV713 granite dump truck equipped with an AI-427 internal EGR engine and introduces experimentation on a 2003 CX613 tractor unit equipped with an AC-460P cooled EGR engine. The paper further assesses the correlation of the field trials to the Mack T-11 engine test and reviews the impact of ultra low sulfur diesel (ULSD) and prototype CJ-4 lubricant formulations in these engines.

Direct injection spark ignition (DISI) engine technology offers tremendous potential advantages in fuel savings and is likely to command a progressively increasing share of the European passenger vehicle market in the future. A concern is its propensity to form deposits on the inlet valve. In extreme cases, these deposits can lead to poor drivability and deteriorating emission performance. This inlet valve deposit build up is a well-known phenomenon in DISI engines since even additised fuel cannot wash over the back of intake valves to keep them clean. Two lubricants and two fuels were tested in a four car matrix. One of the lubricants was a fluid specifically developed by Lubrizol for DISI technology; the other was a baseline oil meeting Ford lubricants requirements and was qualified to ACEA A1/B1/ ILSAC GF2 performance level. Similarly, a baseline fuel was tested against an additised system.

This paper features the results of emission tests conducted on diesel oxidation catalysts, and the combination of diesel oxidation catalysts and water blend fuel (diesel fuel continuous emulsion). Vehicle chassis emission tests were conducted using an urban bus. The paper reviews the impact and potential benefits of combining catalyst and water blend diesel fuel technologies to reduce exhaust emissions from diesel engines.

Soot is a typical byproduct of the diesel fuel combustion process, and a portion of the soot inevitably enters an engine's crankcase. A key functionality of a diesel engine lubricant is to disperse and suspend soot so that larger-particle agglomerations are prevented. The role of soot agglomeration in abrasive engine wear and lubricant viscosity increase is the subject of a continuing investigation; however, what is generally known is that once an engine lubricant loses its ability to control soot and a rapid viscosity increase begins, the lubricant has reached the end of its useful life and should be changed to maximize engine performance and life. This issue of soot related viscosity increase is of such importance that the Mack T-11 engine test was developed as a laboratory tool to evaluate lubricants. The newly proposed Mack EO-N Premium Plus - 03 specification includes a T-11 performance requirement.

Modern multi-grade engine lubricants are formulated to “stay in grade” during field service. Viscosity loss during the early stages of lubricant life is commonly believed to be caused by mechanical degradation of the viscosity modifier in the engine [1]. The Kurt Orbahn shear stability bench test (ASTM D 6278, 30 cycles) has been the industry standard predictor of viscosity loss due to polymer shear in heavy duty diesel engine lubricants. However, the Engine Manufacturers' Association (EMA) has expressed some concern that it underestimates the degree of polymer shear found in certain engines in the field, such as the Navistar 6.0L HEUI (Hydraulic Electronic Unit Injector) Power Stroke engine; a more severe bench test would serve to improve correlation with this and other similar engine designs. This paper offers a new approach for critically examining the relationship between the bench test and field performance.

Modern high power density gasoline fueled engines place an ever-increasing demand on the engine lubricant. In this study, it is shown that advances in engine design to increase performance, improve fuel economy and lower emissions have outpaced the development of typical commercial engine lubricants. Advanced designed engines began to experience oil starvation as a result of a combination of driving cycles, oil quality and poor maintenance practices. The cause was traced to excessive increases in borderline pumping viscosity as measured by MRV TP-1 (ASTM D4684). Used oil analysis for MRV TP-1 showed viscosity greatly increased in excess of stay-in-grade requirements and in many cases the crankcase lubricant was solid at the temperature appropriate for its viscosity grade. However, at the same time CCS values were in grade or only slightly (1W grade) elevated.

Phosphorus is known to reduce effectiveness of the three-way catalysts (TWC) commonly used by automotive OEMs. This phenomenon is referred to as catalyst deactivation. The process occurs as zinc dialkyldithiophosphate (ZDDP) decomposes in an engine creating many phosphorus species, which eventually interact with the active sites of exhaust catalysts. This phosphorous comes from both oil consumption and volatilization. Novel low-volatility ZDDP is designed in such a way that the amounts of volatile phosphorus species are significantly reduced while their antiwear and antioxidant performances are maintained. A recent field trial conducted in New York City taxi cabs provided two sets of “aged” catalysts that had been exposed to GF-4-type formulations. The trial compared fluids formulated with conventional and low-volatility ZDDPs. Results of field test examination were reported in an earlier paper (1).

The tightening legislation in the on-road heavy-duty diesel area means that pollution control systems will soon be widely introduced on such engines. A number of different aftertreatment systems are currently being considered to meet the incoming legislation, including Diesel Particulate Filters (DPF), Diesel Oxidation Catalysts (DOC) and Selective Catalytic Reduction (SCR) systems. Relatively little is known about the interactions between lubricant-derived species and such aftertreatment systems. This paper describes the results of an experimental program carried out to investigate these interactions within DPF, DOC and SCR systems on a state-of-the-art 9 litre engine. The influence of lubricant composition and lube oil ash level was investigated on the different catalyst systems. In order to reduce costs and to speed up testing, test oil was dosed into the fuel. Tests without dosing lubricant into the fuel were also run.

Regulations reducing emissions worldwide are the driving force behind the trend to converging diesel engine design strategies among manufacturers. This results in common engine lubricant performance and the need for a global performance platform for diesel engine lubricants (1, 2). This paper chronicles a multi-year project that defined a diesel engine lubricant platform to meet global Original Equipment Manufacturer (OEM) requirements. The design of the additive chemistry required to achieve the platform targets is described. Demonstration of the performance capabilities of the new technology in engine tests that constitute international specifications and field testing is also discussed. The results suggest that formulating a heavy duty diesel engine oil to meet a variety of worldwide lubricant requirements results in a more robust formulation, outperforming oils designed to meet only regional requirements.

The Environmental Protection Agency will require a reduction in U.S. diesel particulate standards in 1991. To comply with this, the OEM's must modify engine design and ask petroleum refiners to reduce fuel sulfur levels to less than 0.05%. This reduction could have a dramatic impact on an engine's lubricant and possibly its performance. The durability and particulate emission stability of new engines designed to use low sulfur fuel should be related to lubricant performance and protection. Performance with low sulfur fuel must also be acceptable with equipment in service today. Laboratory evaluations of lubricant performance in current equipment were conducted with the Caterpillar 1G2 and various multicylinder diesel tests used for API CE certification. Performance differences attributable to both fuel sulfur and lubricant formulation variations have been identified and will be discussed.

Fuel economy is not an absolute attribute, but is highly dependent on the method used to evaluate it. In this work, two test methods are used to evaluate the differences in fuel economy brought about by changes in engine oil viscosity grade and additive chemistry. The two test methods include a chassis dynamometer vehicle test and an engine dynamometer test. The vehicle testing was conducted using the Federal Test Procedure (FTP) testing protocol while the engine dynamometer test uses the proposed American Society for Testing and Materials (ASTM) Sequence VIE fuel economy improvement 1 (FEI1) testing methodology. In an effort to improve agreement between the two testing methods, the same model engine was used in both test methods, the General Motors (GM) 3.6 L V6 (used in the 2012 model year Chevrolet™ Malibu™ engine). Within the lubricant industry, this choice of engine is reinforced because it has been selected for use in the proposed Sequence VIE fuel economy test.

Motorcycle OEMs faced with stringent global fuel economy and emission regulations are being forced to develop new hardware and emissions control technologies to remain compliant. Motorcycle oils have become an enabling technology for the development of smaller, more efficient engines operating at higher power density. Many OEMs have therefore become reliant on lubricants to not only provide enhanced durability under more extreme operating conditions, but to also provide fuel economy benefits through reduced energy losses. Unlike passenger car oils that only lubricate the engine, motorcycle oils must lubricate both the engine and the drive train. These additional requirements place different performance demands versus a crankcase lubricant. The drive train includes highly loaded gears that are exposed to high pressures, in turn requiring higher levels of oil film strength and antiwear system durability.

A new generation of fluid technology using novel diesel fuel detergent/dispersant chemistry provides a multitude of beneficial effects to the diesel engine, especially the latest model designs. In addition to improved injector, valve and combustion chamber deposit removal, the additive restores power, fuel economy, performance and emission levels1. Positive observations have also been documented along with improved performance concerning crankcase lube viscosity, soot loading and TBN retention. An even greater added benefit is the inherent capability of the fuel additive to deal with several EGR issues now prominent with the introduction of new engines. Recent research, reported herein, has uncovered the extensive efficacy of this chemistry for piston durability and neutralization of ring corrosion phenomena. All of the beneficial additive attributes are further enhanced with increased oxidative and thermal fuel stability and no loss of filterability.

The next generation of engine oil under development has been formulated to maintain beneficial oil lubrication properties at increased engine operating temperatures, increased drain-oil intervals, and with the recirculation of exhaust gas back through the engine (EGR). These conditions result in the formation of degradation products from decomposed fuel, additives, and base oil. Decomposition products containing reactive sulfur can result in the corrosion of copper alloys. Sulfur-containing compounds currently used in these formulations can include zinc dithiophosphates (ZDP), molydithiophosphates, molydithiocarbamates, and molybdic acid/amine complexes, along with sulfur containing detergents and antioxidants. Interactions among these components and others in the formulation often determine the propensity of these formulations for corrosion. This paper will discuss the results of corrosion bench tests used to screen oil formulations for copper corrosion.

Four 1998 Mitsubishi Carismas, two equipped with direct injection (GDI) and two with port fuel injection engines (PFI) were tested in a designed experiment to determine the effect of mileage accumulation cycle, engine type, fuel and lubricant type on engine wear and engine oil performance parameters. Fuel types were represented by an unadditised base fuel meeting EEC year 2000 specifications and the same base fuel plus synthetic deposit control additive packages. Crankcase oils were represented by two types (1) a 5W-30 API SJ/ILSAC GF-2 type engine oil and (2) a 10W-40 API SH/CF ACEA A3/ B3-96 engine oil. The program showed that specific selection of oil additive chemistry may reduce formation of intake valve deposits in GDI cars.. In general, G-DI engines produced more soot and more pentane insolubles and were found to be more prone to what appears to be soot induced wear than PFI engines.