Search Results

Assuming rigid body motion, recorded acceleration and recorded roll rates at the center of gravity, equations are used to calculate the local three-dimensional accelerations at hypothetical seating positions' Emergency Locking [seat belt] Retractors (ELR) during a steer induced rollover crash. For a threshold of 0.7 g, results demonstrated that intervals in the vehicle's response that may cause the ELR's inertial sensor to move into a neutral zone were limited to localized high magnitude negative vertical acceleration events during the rollover segment with a median duration of 4 ms, average duration of 4.8 ms and a maximum calculated duration of 31.7 ms. Changing the threshold to 0.35 g reduced the interval count by 70 percent and maximum duration by approximately 50 percent.

Plane strain bending (e.g. bending about a straight line) is a major sheet forming operation and it is practiced as brake bending (air bending, U-die, V-die and wiping-die bending). Precise prediction of springback is the key to the design of the bending dies and to the control of the process and press brake to obtain close tolerances in bent parts. In this paper, reliable mathematical models for press brake bending are presented. These models can predict springback, bendability, strain and stress distributions, and the maximum loads on the punch and die. The elasto-plastic bending model incorporates the true (nonlinear) strain distribution across the sheet thickness, Swift's strain hardening law, Hill's 1979 nonquadratic yield criterion for normal anisotropic materials, and plane strain deformation mode.

Shrink flanging is a major sheet forming operation to produce convex flanges in structural sheet metal components. Flanges are used for appearance, rigidity, hidden joints, and strengthening of the edge of sheet parts such as automobile front fender and complex panels formed by stretch/draw forming. Wrinkling around the flange edge is the major defect in shrink flanging operation. There has been a lack of reliable mathematical modeling to predict the strains and wrinkles in shrink flanging operations. A trial-and-error approach has been usually practiced in tooling and process designs. In this paper, a wrinkling criterion in shrink flange is proposed based on a simplification from a general criterion for a doubly curved anisotropic shell. The mathematical model for strain analysis in shrink flanging is established based on Wang and Wenner's strain model for stretch flange. Shrink flanging experiments were conducted to validate the theories.

Predominant failure modes in the forming of sheet metal parts are wrinkling and tearing. Wrinkling may occur at the flange as well as in other areas of the drawn part and is generated by excessive compressive stresses that cause the sheet to buckle locally. Fracture occurs in a drawn material which is under excessive tensile stresses. For a given part and blank geometries, the major factors affecting the occurrence of defects in sheet metal parts are the blank holder force (BHF) and the blank holder pressure (BHP). These variables can be controlled to delay or completely eliminate wrinkling and fracture. Modern mechanical presses are equipped with hydraulic cushions and various advanced multi-point pressure control systems. Thus, the BHP can be adjusted over the periphery of the blank holder as a function of location and time (or press stroke).

The motivation of this paper is inverse estimation of the material properties for sheet metals subjected to cyclic loading. Cyclic three-point bending tests are performed. Bending moments are computed from the measured data, namely, punch stroke, punch load, bending strain and bending angle. Bending moments are also calculated based on the selected material model in which normal anisotropy and combined hardening are considered. Material parameters are identified by minimizing the difference between these two bending moments. Modified Levenberg-Marquardt method is used in the optimization procedure. Stress-strain curves are generated with the optimized material parameters.

In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fractures, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important parameters in sheet forming process control. However, drawbead design and drawbead force adjustment still rely on trial-and-error procedures. This paper summarizes the guidelines in drawbead design, evaluates a number of mathematical models in estimating drawbead forces, and investigates the effects of sheet thickness, material properties, drawbead geometry and penetration on the drawbead force.

Reported tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys indicate that those values depend on the size and shape of the test samples and their global porosities. This paper reviews the mechanical properties reported in the open literature for these die cast alloys and indicates that section thickness and global porosity are inadequate for predicting the tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys.

For some vehicle dynamics applications, an estimate of a vehicle's center of gravity (cg) height and mass moments of inertia can suffice. For other applications, such as vehicle models and simulations used for vehicle development, these values should be as accurate as possible. This paper presents several topics related to inertial parameter estimation and measurement. The first is a simple but reliable method of estimating vehicle mass moment of inertia values from data such as the center of gravity height, roof height, track width, and other easily measurable values of any light road vehicle. The second is an error analysis showing the effect, during a simple static cg height test, of vehicle motion (relative to the support system) on the vehicle's calculated cg height. A method of accounting for this motion is presented. Similarly, the effects of vehicle motion are analyzed for subsequent mass moment of inertia tests.

The process of producing co-continuous ceramic composite material has been investigated in order to provide a greater understanding of the formation mechanism and hence evaluate the viability of commercial applications for these exciting new materials. The ease of manufacture for components combined with the low production cost hold great promise for the production of brake rotors, brake calipers, piston crowns, cylinder liners, gears and turbine compressors. Practical issues such as bonding to this material, together with the machinability have been addressed, our findings are presented in this paper.

A newly developed process allows the near-net shape fabrication of alumina/aluminum composite bodies via the immersion of a sacrificial oxide preform into a molten aluminum alloy bath. The resulting composite possesses an attractive range of properties for application in several automotive components. These properties include: high strength and stiffness, appreciable thermal and electrical conductivity, high strength at elevated temperatures, coefficient of thermal expansion of 10 X 10-6 C-1 and relative ease of machinability. Low cost fabrication renders this material/process ideal for components such as brake rotors and calipers, cylinder bore liners, piston components.

The handling, stability, and rollover resistance of vehicles is presently being studied by both the automotive industry and the National Highway and Traffic Safety Administration (NHTSA). However, to study the handling and rollover behavior of each vehicle on the road is not feasible. The ability to categorize and compare the rollover and handling behavior of various vehicles is a subject of considerable research interest. This paper examines the possibility of characterizing vehicle classes through the use of a three degree-of-freedom linear model. Initially, segregation is studied by evaluating the eigenvalue location in the complex domain for vehicle sideslip velocity, yaw rate, and roll angle. Then the influence of numerator dynamics on vehicle behavior is studied and vehicle class segregation is attempted through evaluation of the amplitude ratio of the frequency responses for sideslip velocity, yaw rate, and roll angle.

A new technique for measuring the friction coefficient between the punch and workpiece during sheet forming operations has been developed at the Ohio State University. Various materials, such as interstitial-free (IF) steel, high strength (HS) steel, an aluminum alloy (2008T4) and 70/30 brass, were tested under dry and oil lubrication conditions at different punch rates and process conditions. The results show that punch friction depends on the angle of wrap, which varies with punch stroke, and on the strain rate, which depends on punch velocity. The O.S.U. Friction Test is described and typical results are presented which verify the usefulness of the new procedure.