Search Results

When evaluating the wear properties of slide bearings for car engines, it is a common practice to conduct long-term physical test using a bearing tester for screening purposes according to the revolution speed of the shaft, supply oil temperature and bearing pressure experienced in the actual use of engines. The loading waveform applied depends on the capability of the tester that is loaded, and it is often difficult to apply a loading waveform equivalent to that of actual engines. To design an engine that is more compact or lighter, it is necessary to reduce the dimensions of slide bearings and the distance between bearings. This requires loading tests on a newly designed engine by applying a loading waveform equivalent to that of actual engines to slide bearings and their vicinity before conducting a firing test. We therefore conducted an engine firing test by attaching thin-film sensors to the slide bearing part of the engine and measured the actual load distribution.

When a vehicle is cruising, unpleasant noise in the 4 to 5 KHz high-frequency band can be heard at the center of all seats in the vehicle cabin. In order to specify the source of this noise, the correlation between the noise and airborne noise from the outer surface of the transmission was determined, and transfer path analysis was conducted for the interior of the transmission. The results indicated that the source of the noise was the 0th-order breathing mode specific to the drive motor. To make it possible to predict this at the desk, a vibrational analysis method was proposed for drive motors made up of laminated electrical steel sheets and segment-type coils. Material properties data for the electrical steel sheets and coils was employed in the drive motor vibrational analysis model without change. The shapes of the laminated electrical steel sheets and coils were also accurately modeled.

At present, biodiesel fuels using natural-origin materials are expanding in share, and there are many different kinds. Biodiesel fuel generates organic acid when it deteriorates, so care is needed when evaluating the influence of the fuel on automotive fuel-line materials. A model biodiesel fuel was designed taking into account deterioration of the fuel and mixing of impurities into it. Durability of automotive fuel-line rubber and plastic materials were evaluated by using the model fuel. From the evaluation results, it was found that fluoroelastomer (hereafter referred to as FKM) and polyacetal resin (hereafter referred to as POM) deteriorate depending on specific fuel properties and deterioration state. In this paper, we report evaluating results of biodiesel fuels on the automotive fuel-line rubber and plastic materials, and the importance of biodiesel fuel property management.

This paper proposes a technology to reduce vehicle surge during towing that utilizes motors and shifting to help ensure comfort in a parallel HEV pickup truck. Hybridization is one way to reduce fuel consumption and help realize carbon neutrality. Parallel HEVs have advantages in the towing, hauling, and high-load operations often carried out by pickup trucks, compared to other HEV systems. Since the engine, motor, torque converter, and transmission are connected in series in a parallel HEV, vehicle surge may occur when the lockup clutch is engaged to enhance fuel efficiency, similar to conventional powertrains. Vehicle surge is a low-frequency vibration phenomenon. In general, the source is torque fluctuation caused by the engine and tires, with amplification provided by first-order torsional driveline resonance, power plant resonance, suspension resonance, and cabin resonance. This vibration is amplified more during towing.

Downsizing or higher compression ratio of SI engines is an appropriate way to achieve considerable improvements of part load fuel efficiency. As the compression ratio directly impacts the engine cycle thermal efficiency, it is important to increase the compression ratio in order to reduce the specific fuel consumption. However, when operating a highly boosted / downsized SI engine at full load, the actual combustion process deviates strongly from the ideal Otto cycle due to the increased effective loads requiring ignition timing delay to suppress abnormal combustion phenomena such as engine knocking. This means that for an optimal design of an SI engine between balances must be found between part load and full load operation. If the knocking characteristic can be accurately predicted beforehand when designing the combustion chamber, a reduction of design time and /or an increase in development efficiency would be possible.

High fuel efficiency and low emission technologies, such as Direct Injection (DI) gasoline and diesel engines and hybrid powertrains, have been developed to resolve environmental and energy resource issues. The hybrid powertrain system has achieved superior power performance as well as higher system efficiency and is expected to be a core powertrain technology because it is compatible with various power sources including fuel cells. It becomes important to control complicated hybrid systems that consist of not only a powertrain but also vehicle systems such as regenerative braking. Model-based control and calibration enables both control strategy optimization and control system development efficiency improvement.

The renewed platform of the upcoming flagship front-engine, rear-wheel drive (FR) vehicles demands high levels of driving performance, fuel efficiency and noise-vibration performance. The newly developed driveline system must balance these conflicting performance attributes by adopting new technologies. This article focuses on several technologies that were needed in order to meet the demand for noise-vibration performance and fuel efficiency. For noise-vibration performance, this article will focus on propeller shaft low frequency noise (booming noise). This noise level is determined by the propeller shaft’s excitation force and the sensitivity of differential mounting system. In regards to the propeller shaft’s excitation force, the contribution of the axial excitation force was clarified. This excitation force was decreased by adopting a double offset joint (DOJ) as the propeller shaft’s second joint and low stiffness rubber couplings as the first and third joints.

New engine controls have been developed for the turbocharged Lexus NX200t to improve driving power by reducing engine torque output lag. Drive power management functions have been centralized in an integrated drive power control system. The newly developed controls minimize the potential reduction in drivability associated with the adoption of a turbocharged engine while improving fuel efficiency. General driveability issues commonly associated with a turbocharged engine include sudden increases in drive power due to the response lag of the turbocharger, and higher shifting frequencies if this response lag triggers a disturbed accelerator operation pattern by the driver. The developed technologies detect and control sudden increases in drive power to create the optimum drive power map, and reduce unnecessary shifts even if the driver's accelerator operation is disturbed.

The purpose of this paper is to construct the thermal analysis model by measuring and estimating the temperature at the traction contact area. For measurement of temperature, we have used a thin-film temperature sensor. For estimation of temperature, we have composed the thermal analysis model. The thin-film temperature sensor was formed on the contact surface using a spattering device. The sensor is constituted of three layers (sensor layer, insulation layer and intermediate layer). Dimensions of the sensor were sufficiently smaller than the traction contact area. The sensor featured high specific pressure capacity and high speed responsiveness. The thermal analysis model was mainly composed of three equations: Carslaw & Jaeger equation, Rashid & Seireg equation and heat transfer equation of shear heating in oil film. The heat transfer equation involved two models (local shear heating model at middle plane, homogeneous shear heating model).

In recent years, the increased use of electric power steering in vehicles has increased the importance of issues such as making systems more compact and lightweight, and dealing with increased development man-hours. To increase development efficiency, the use of a “Hardware in the loop simulator” (HILS) is being tested to shift from the previous development method that relied on a driver's subjective evaluation in an actual vehicle test to bench-test development. Using HILS enables tasks such as specification studies, performance forecasts, issue identification and countermeasure proposals to be performed at an early stage of development even when there is no prototype vehicle. This report describes a case study of using HILS to solve the issues of reducing the load by adjusting the geometric specifications around the kingpin and eliminating the tradeoff by adding a new EPS control algorithm in order to make the electric power steering (EPS) more compact and lightweight.

The engine in the new fourth generation Prius carries over the same basic structure as the 2ZR-FXE used in the third generation and incorporates various refinements to enhance fuel efficiency. Called the ESTEC 2ZR-FXE, the new engine incorporates various fuel efficient technologies to improve combustion characteristics, knocking, and heat management, while also reducing friction. As a result of this meticulous approach to enhancing fuel efficiency, the new engine is the first gasoline engine in the world to achieve a maximum thermal efficiency of 40%. This paper describes the fuel efficient technologies incorporated into this engine.

Recently, global warming and energy security have received significant attention. Thus an improvement of the vehicle fuel economy is strongly required. For engines, one effective way is to improve the engine thermal efficiency. Raising compression ratio [1] or turbo charging technologies have potential to achieve high thermal efficiency. However knock does not allow the high thermal efficiency. Knock depends on the fuel composition and the pressure and temperature history of unburnt end-gas [2-3]. For fuels, RON is well known for describing the anti knock quality. High RON fuels have high anti knock quality and result in higher thermal efficiency. This paper investigates the impact of high RON fuels on the thermal efficiency by using high compression ratio engine, turbo charged engine, and lean boosted engine [4]. Finally, it is shown that the high thermal efficiency can be approached with high RON gasoline and ethanol.

For viscous couplings(VCs) as a driving force transmission system of vehicles, requirement of torque characteristics has been getting very stringent. Because the torque characteristics significantly affect four wheel drive vehicles' abilities such as traction performance and driving stability. Furthermore, the recent concerns on high fuel economy, low pollution and low cost require that design of VCs should be increasingly compact, light weighted and excellent in transmitted torque's stability. It is an easy way to increase viscosity of viscous coupling fluids(VCFs) for the compact design of the VC. But it might cause increase in heat load and wear of plates which resulted in degradation of the VCF. The degradation affects VCF's viscosity and impairs stability in torque transmission. Therefore it is indispensable to develop high viscosity VCF which is excellent in long-term viscosity's stability.

When the strain is temporarily stopped during tensile testing of a metal, a stress relaxation phenomenon is known to occur whereby the stress diminishes with the passage of time. This phenomenon has been explained as the change of elastic strain into plastic strain. A technique was devised for deliberately causing strain dispersion to occur by applying the stress relaxation phenomenon during stamping. A new step motion that pause the die during forming was devised; it succeeded in modifying the deep-draw forming limit by a maximum of 40%. This new technique was verified through tensile and actual stamping tests. It was confirmed that the use of step motion causes the strain to disperse, thereby modifying the deep draw forming limit. The degree to which the forming limit is modified is dependent on the stop time and the temperature. Step motion technology increases the stampability of high-strength, forming-resistant materials and allows for expanded application of these materials.

Introducing effective technologies to reduce carbon emissions in the transport sector is a critical issue for automotive manufacturers to contribute to sustainable development. Unlike the plug-in electric vehicles (PEVs), whose effectiveness is dependent on the carbon intensity of grid electricity, the solar hybrid vehicle (SHV) can be an alternative electric vehicle because of its off-grid, zero-emission electric technology. Its usability is also advantageous because it does not require manual charging by the users. This study aims at evaluating the economic, environmental, and usability benefits of SHV by comparing it with other types of vehicles including PEVs. By setting cost and energy efficiency on the basis of the assumed technology level in 2030, annual cost and annual CO2 emissions of each vehicle are calculated using the daily mileage pattern obtained from a user survey of 5,000 people in Japan and the daily radiation data for each corresponding user.

In our preceding report [1], we showed that the thermal conductivity of a heat pipe dramatically improves during high-speed reciprocation. However, this cooling method has rarely been applied to car engine pistons because the thermal conductivity of commercially available heat pipes does not increase easily even if the pipe is subjected to high-speed reciprocation. In consideration of the data from our preceding report, we decided to investigate heat pipe designs for car engine pistons, propose an optimum design, and conduct thermal analysis of the design. As a result, we found that it is possible to transport heat from the central piston head area, where cooling is most needed, to the piston skirt area, suggesting the possibility of efficient cooling.

Car engine piston cooling is an important technology for improving the compression ratio and suppressing the deformation of pistons. It is well known that thermal conductivity improves dramatically through the use of heat pipes in computers and air conditioners. However, the heat pipes in general use have not been used for the cooling of engines because the flow of gas and liquid is disturbed by vibration and the thermal conductivity becomes excessively low. We therefore developed an original heat pipe and conducted an experiment to determine its heat transfer coefficient using a high-speed reciprocation testing apparatus. Although the test was based on a single heat pipe unit, we succeeded in improving the heat transfer coefficient during high-speed reciprocation by a factor of 1.6 compared to the heat transfer coefficient at standstill. This report describes the observed characteristics and the method of verification.

The use of waste heat for automobile engine that applied Rankine cycle from the viewpoint of exergy (available energy) was researched. In order to recover heat to high quality energy, a heat-management engine whose exhaust port was replaced with an innovative evaporation device was developed. With this engine, high temperature and high pressure steam (400 degree C, 8MPa) could be generated from a large amount of the exhaust loss. In addition, high temperature water (189 degree C) was obtained from cooling loss. Consequently, the system that recovered more exergy from waste heat was established. To verify the system, the Rankine cycle system was installed in a hybrid vehicle and the automatic control system to change steam temperature and pressure according to the load variation was constructed. As the result of vehicle testing, thermal efficiency was increased from 28.9% to 32.7% (by 13.2% increase) at 100km/h constant vehicle speed.

To increase energy utilization efficiency of a micro combined heat and power generation unit, methods for simultaneously enhancing efficiencies of power generation and of heat recovery, which are normally in the trade-off relationship has been studied. To increase power generation efficiency, an extended expansion linkage engine higher in thermal efficiency than conventional engines has been adopted. The power generation efficiency was enhanced by 3.8 points to 26.3% from 22.5% of a conventional model. However, since introducing an extended expansion engine increases kinetic energy and lowers the temperature of exhaust gas from the engine, it is difficult to enhance the heat recovery. Focusing on the fact that most released heat energy is discharged through ventilation from the unit, ventilation cooling system was reexamined, and reduction of the released heat energy was considered.

An examination was made on the effect of low-viscosity engine oil on fuel efficiency improvements and engine reliability for the purpose of improving fuel efficiency through the use of select engine oils. Fuel efficiency-improving effects were estimated by measuring friction torque using low-viscosity engine oil. The results show that reducing engine oil viscosity is effective for improving fuel efficiency. In examining engine reliability, attention was paid to the following two aspects which are concerns in practical performance that may arise when engine oil viscosity is reduced. Engine oil consumption Sliding wear at high temperatures Tests and analyses were conducted to develop indexes for engine oil properties that are strongly correlated with each of these two concerns. A strong correlation was found between engine oil consumption and the results of a thermogravimetric analysis, and between high-temperature sliding wear and high-temperature, high-shear viscosity (HTHS).