Search Results

Generally, automobiles have many performance requirements for comfort, of which noise, vibration and harshness are very important. Toyota Motor Corporation equipped several 2003 models with the second-generation Electronically Controlled Brake system (ECB2). These ECB2 actuator units adopted a new structure that reduced pumping noise by controlling the skew phenomena of needle roller bearings. Normally, needle roller bearings are advantageous over other bearings in cases where a large force is loaded on bearings, because the contact areas can be made larger. However, a thrust force arises from skew phenomena because of minute clearances among the component parts of needle roller bearings. As a result, axial vibration of the bearing shaft sometimes occurs due to the thrust force. This paper explains how the thrust force generated from the skew phenomena of needle roller bearings occasionally affects the pumping vibration level of equipped machinery such as the brake actuator unit.

In order to clarify future automobile technologies and fuel qualities to improve air quality, second phase of Japan Clean Air Program (JCAPII) had been conducted from 2002 to 2007. Predicting improvement in air quality that might be attained by introducing new emission control technologies and determining fuel qualities required for the technologies is one of the main issues of this program. Unregulated material WG of JCAPII had studied unregulated emissions from gasoline and diesel engines. Eight gaseous hydrocarbons (HC), four Aldehydes and three polycyclic aromatic hydrocarbons (PAHs) were evaluated as unregulated emissions. Specifically, emissions of the following components were measured: 1,3-Butadiene, Benzene, Toluene, Xylene, Ethylbenzene, 1,3,5-Trimethyl-benzene, n-Hexane, Styrene as gaseous HCs, Formaldehyde, Acetaldehyde, Acrolein, Benzaldehyde as Aldehydes, and Benzo(a)pyrene, Benzo(b)fluoranthene, Benzo(k)fluoranthene as PAHs.

We have developed a novel engine cycle simulation program (UniDES: universal diesel engine simulator) to reproduce the diesel combustion process over a wide range of engine operating parameters, such as the amount of injected fuel, the injection timing, and the EGR ratio. The approach described in this paper employs a zoning model, where the in-cylinder region is divided into up to five zones. We also applied a probability density function (PDF) concept to each zone to consider the effect of spatial non-homogeneities, such as local equivalence ratios and temperature, on the combustion characteristics. We linked this program to the commonly used commercial GT-Power® software (UniDES+GT). As a result, we were able to reproduce transient engine behavior very accurately.

The aim of this research is to develop the diesel combustion simulation (UniDES: Universal Diesel Engine Simulator) that incorporates multiple-injection strategies and in-cylinder composition changes due to exhaust gas recirculation (EGR), and that is capable of high speed calculation. The model is based on a zero-dimensional (0D) cycle simulation, and represents a multiple-injection strategy using a multi-zone model and inhomogeneity using a probability density function (PDF) model. Therefore, the 0D cycle simulation also enables both high accuracy and high speed. This research considers application to actual development. To expand the applicability of the simulation, a model that accurately estimates nozzle sac pressure with various injection quantities and common rail pressures, a model that accounts for the effects of adjacent spray interaction, and a model that considers the NOx reduction phenomenon under high load conditions were added.

A phosphor thermometry, for measurements of two-dimensional gas-phase temperature was examined in turbulent combustion in an engine. The reasonable temperature deviation and the agreement with calculated data within 5% precision were achieved by single-shot images in the ignition process of compression ignition engine. Focusing on the local flame kernel, the flame structure could be quantitatively given by the temperature. It became evident that the HCCI flame kernels had 1-3 mm diameter and the isolated island structures. Subsequently, the HTR zone consisted of the combined flame kernels near TDC.

High fuel efficiency and low emission technologies, such as Direct Injection (DI) gasoline and diesel engines and hybrid powertrains, have been developed to resolve environmental and energy resource issues. The hybrid powertrain system has achieved superior power performance as well as higher system efficiency and is expected to be a core powertrain technology because it is compatible with various power sources including fuel cells. It becomes important to control complicated hybrid systems that consist of not only a powertrain but also vehicle systems such as regenerative braking. Model-based control and calibration enables both control strategy optimization and control system development efficiency improvement.

The renewed platform of the upcoming flagship front-engine, rear-wheel drive (FR) vehicles demands high levels of driving performance, fuel efficiency and noise-vibration performance. The newly developed driveline system must balance these conflicting performance attributes by adopting new technologies. This article focuses on several technologies that were needed in order to meet the demand for noise-vibration performance and fuel efficiency. For noise-vibration performance, this article will focus on propeller shaft low frequency noise (booming noise). This noise level is determined by the propeller shaft’s excitation force and the sensitivity of differential mounting system. In regards to the propeller shaft’s excitation force, the contribution of the axial excitation force was clarified. This excitation force was decreased by adopting a double offset joint (DOJ) as the propeller shaft’s second joint and low stiffness rubber couplings as the first and third joints.

Exhaust emissions are well known to have adverse impacts on human health. Studies have demonstrated that there is an association between ambient particulate matter (PM) levels and various harmful cardiopulmonary conditions. Soot exhaust from diesel engines can be a significant contributor to airborne pollutants. A key component in PM level control for a diesel engine is a diesel particulate filter (DPF). This device traps soot while allowing other exhaust gases to pass unhindered. However, the performance of diesel particulate filters can change with increasing soot loadings and thus may require regeneration or replacement. Improved understanding of diesel particulate filters is dependent upon the knowledge of the actual soot loading and the soot distribution within the DPF. Neutron radiography (NR) has been identified as an effective means of non-destructively identifying hydrogen or carbon adsorbed in PM.

Generally, soot emissions increase in diesel engines with smaller bore sizes due to larger spray impingement on the cavity wall at a constant specific output power. The objective of this study is to clarify the constraints for engine/nozzle specifications and injection conditions to achieve the same combustion characteristics (such as heat release rate and emissions) in diesel engines with different bore sizes. The first report applied the geometrical similarity concept to two engines with different bore sizes and similar piston cavity shapes. The smaller engine emitted more smoke because air entrainment decreases due to the narrower spray angle. A new spray design method called spray characteristics similarity was proposed to suppress soot emissions. However, a smaller nozzle diameter and a larger number of nozzle holes are required to maintain the same spray characteristics (such as specific air-entrainment and penetration) when the bore size decreases.

1 Recently, demand for small-bore compact vehicle engines has been increasing from the standpoint of further reducing CO2 emissions. The generalization and formulation of combustion processes, including those related to emissions formation, based on a certain similarity of physical phenomena regardless of engine size, would be extremely beneficial for the unification of development processes for various sizes of engines. The objective of this study is to clarify what constraints are necessary for engine/nozzle specifications and injection conditions to achieve the same combustion characteristics (such as heat release rate and emissions) in diesel engines with different bore sizes.

We have developed a method by which the oil flow rate can be measured by using a hot-wire sensor that could be installed in the passages of actual engine lubricant oil. This measuring method proves to have a ±5% accuracy and a 40kHz response that enables ‘real time’ function. Thus, observation of (1) the effect of bearing clearance, and (2) the fluctuating mechanism of the oil flow per 1 degree crank angle from the point of engine start-up to 6000r/min and full load can be achieved, and the timing and quantity of intermittent oil-jet from the oil hole in connecting rod were ascertained.

In many countries, cetane number and distillation properties of diesel fuel have been changing, thus affecting the performance of diesel engines. This paper describes investigations made on the effect of diesel fuel quality on white smoke (one of the important emissions of diesel engines). The result of simple laboratory tests simulating high altitude conditions plus field tests using three types of disel engines supplied with various types of diesel fuels is given. It was found that white smoke appearing tendency correlated best with cetane number and the 90 percent distillation point of the fuel. The field tests performed at high altitude correlated well with the simple laboratory tests.

The effects of diesel fuel properties (aromatic content, cetane index and T90), cetane improver, oxygenates, high boiling point hydrocarbons and aromatics distribution on diesel exhaust emissions were studied under the Japanese 10-15 test cycle and the ECE+EUDC test cycle. The test vehicle was a TOYOTA COROLLA with a natural aspirated, 2.0L displacement, IDI diesel engine. It was demonstrated that particulate emissions are highly correlated with T90 and that NOx is affected by the aromatic content of fuel. A reduction in particulates emissions was observed in fuel with a lower cetane number by adding cetane improver, but this reduction was limited. Cetane improver had no effect on NOx emissions in the 45 # 60 cetane number range. Oxygenates reduced particulate emissions remarkably but had little effect on NOx emissions. A decrease in the soot in particulates was particularly observed.

Diesel emissions are significant issue worldwide, and emissions requirements have become so tough that. the application of after-treatment systems is now indispensable in many countries To meet even more stringent future emissions requirements, it has become apparent that the improvement of market fuel quality is essential as well as the development in engine and exhaust after-treatment technology. Japan Clean Air Program II (JCAP II) is being conducted to assess the direction of future technologies through the evaluation of current automobile and fuel technologies and consequently to realize near zero emissions and carbon dioxide (CO2) emission reduction. In this program, effects of fuel properties on the performance of diesel engines and a vehicle equipped with two types of diesel NOx emission after-treatment devices, a Urea-SCR system and a NOx storage reduction (NSR) catalyst system, were examined.

For diesel engines, the delay of injection timing causes the white smoke due to unburned fuel in cold conditions. To define the effective engineering against the white smoke, we studied this occurrence mechanism by observing the white smoke in the cylinder through the glass window, and quantitatively measuring some factors. As a result, it is found that the white smoke quantity is closely correlated with the wall adhesion quantity of injected fuel, and proved that the evaporation acceleration by restraint of the fuel adhesion to the combustion chamber wall is effective to reduce the white smoke.

In recent years, problems such as global warming, the depletion of natural resources, and air pollution caused by emissions are emerging on a global scale. These problems call for efforts directed toward the development of fuel-efficient engines and exhaust gas reduction measures. As a solution to these issues, performance improvements should be achieved on the oil that lubricates the sliding sections of engines. This report points to features required of future engine oil-such as contribution to fuel consumption, minimized adverse effects on the exhaust gas aftertreatment system, and improved reliability achieved by sludge reduction-and discusses the significance of these features. For engine oil to contribution of engine oil to lower fuel consumption, we examined the effects of reduced oil viscosity on friction using gasoline and diesel engines.

In this study, we combined a diesel engine with the Toyota Hybrid System (THS). Utilizing the functions of the THS, reducing engine friction, lowering the compression ratio, and adopting a low pressure loop exhaust gas recirculation system (LPL-EGR) were examined to achieve both low fuel consumption and low nitrogen oxides (NOx) emissions over a wide operating range. After applying this system to a test vehicle it was verified that the fuel economy greatly surpassed that of a conventional diesel engine vehicle and that NOx emissions could be reduced below the value specified in the Euro 6 regulations without DeNOx catalysts.

Small bore diesel engines often adopt a two-valve cylinder head and a non-central injector layout to expand the port flow passage area. This non-central injector layout causes asymmetrical gas flow and fuel distribution, resulting in worse heat losses and a less homogenous fuel-air mixture than an equivalent four-valve cylinder head layout with a central injector. This paper describes the improvement of piston bowl geometry to achieve a more homogeneous gas flow and fuel-air mixture. This concept reduced fuel consumption by 2.5% compared to the original piston bowl geometry, while also reducing NOx emissions by 10%.

The emission regulations for diesel engines are continually becoming stricter to reduce pollution and conserve energy. To meet these increasingly stringent regulations, a new exhaust after-treatment device is needed. Recently, the authors proposed the simultaneous electrochemical reduction (ECR) system for diesel particulate matter (PM) and NOx. In this method, a gas-permeable electrochemical cell with a porous solid oxide electrolyte is used for PM filtering on the anode. Alkaline earth metal is coated on the cathode for NOx storage. Application of voltage to both electrodes enables the simultaneous reduction of PM and NOx by the forced flow of oxygen ions from the cathode to the anode (oxygen pumping). In this study, the basic characteristics of the ECR system were investigated, and a disk-shaped electrochemical cell was evaluated.

A new after-treatment system called DPNR (Diesel Particulate-NOx Reduction System) has been developed for simultaneous and continuous reduction of particulate matter (PM) and nitrogen oxides (NOx) in diesel exhaust gas. This system consists of both a new catalytic technology and a new diesel combustion technology which enables rich operating conditions in diesel engines. The catalytic converter for the DPNR has a newly developed porous ceramic structure coated with a NOx storage reduction catalyst. A fresh DPNR catalyst reduced more than 80 % of both PM and NOx. This paper describes the concept and performance of the system in detail. Especially, the details of the PM oxidation mechanism in DPNR are described.