Search Results

Generally, automobiles have many performance requirements for comfort, of which noise, vibration and harshness are very important. Toyota Motor Corporation equipped several 2003 models with the second-generation Electronically Controlled Brake system (ECB2). These ECB2 actuator units adopted a new structure that reduced pumping noise by controlling the skew phenomena of needle roller bearings. Normally, needle roller bearings are advantageous over other bearings in cases where a large force is loaded on bearings, because the contact areas can be made larger. However, a thrust force arises from skew phenomena because of minute clearances among the component parts of needle roller bearings. As a result, axial vibration of the bearing shaft sometimes occurs due to the thrust force. This paper explains how the thrust force generated from the skew phenomena of needle roller bearings occasionally affects the pumping vibration level of equipped machinery such as the brake actuator unit.

Improvement of vehicle dynamics in limit cornering have been studied. Simulations and tests have verified that vehicle stability and course trace performance in limit cornering have been improved by active brake control of each wheel. The controler manages vehicle yaw moment utilizing difference braking force between left and right wheels, and vehicle deceleration utilizing sum of braking forces of all wheels.

In-wheel motors (IWM) will be a key technology that contributes to the popularization of electric vehicles. Combining electric drive with IWM enables both good vehicle dynamics and a roomy interior. In addition, the responsiveness of IWM is also capable of raising dynamic control performance to an even higher level. IWM enable vertical body motion control as well as direct yaw control, electric skid control, and traction control. This means that IWM can replace most control actuators used in a vehicle chassis. The most important technology for IWM is to enable the motor to coexist with the brake and the suspension arms inside the wheel. The IWM drive unit described in this paper can be installed with a front double wishbone suspension, the most difficult configuration.

In vehicle control systems such as ABS (anti-lock braking system) or active suspension control, sensors for detecting longitudinal and/or lateral acceleration of vehicles (acceleration of up to ± 9.8 m/s2, with frequency range of DC to 20 Hz) is necessary. The principle of acceleration detection for this sensor is as follows. A permanent magnet levitates steadily in magnetic fluid by the action of the magnetic field generated by the magnet itself. The magnet moves by the application of acceleration on the mass of the magnet. This change of position of the magnet is detected by the Hall element, and thus acceleration is measured as an electrical signal. This sensor consists of only magnetic fluid, a permanent magnet, housing, a pair of Hall elements and an electronic circuit.

Sensors which can detect minimal acceleration such as ± 9.8 m/sec2 in longitudinal and lateral direction of a vehicle, for DC to 20 Hz range, are required to control ABS (anti-lock braking system) or suspension system. To fulfill these requirements, we have developed a one-dimensional acceleration sensor, using magnetic fluid, to control the vehicle. In 1992, we submitted a paper on this sensor at the SAE International Congress and Exposition. Based on this one-dimensional acceleration sensor, we have developed an acceleration sensor which can detect two dimensional acceleration using a single inertia mass. This sensor is compact and can detect minimal acceleration with high accuracy. Spring and damping functions were obtained via the adoption of magnetic fluid, as in the case of the former one-dimensional acceleration sensor. This sensor can sustain mechanical shocks.

Excessive throttle pedal operation while driving on slippery roads causes the wheels to spin, consequently reducing vehicle stability and traction. Driving a vehicle under these conditions imposes additional and unneccessary burdens on the driver. To solve the problem, a traction control (TRC) system controlling engine torque and brake force has been developed to prevent the driven wheels from excessive spinning. The TRC system consists of some additional components to the Antilock Brake System (ABS), a system which had previously been developed to prevent wheels from locking up during hard braking. The combination of the ABS and the TRC system will now be effective to assist the driver to improve the vehicle driving performance on slippery road surfaces.

One of the innovations for the Lexus LS400 is the development of a traction control system (TRAC system). The TRAC system suppresses the spinning of the driven wheels, which occurs easily on slippery roads during excessive acceleration, and it improves the acceleration performance and the stability of the car. The TRAC system controls the engine sub-throttle angle and the brake hydraulic pressure for the driven wheels in the same way as the traction control system for the 1987 Toyota Crown. But, acceleration performance and stability of Lexus LS400 is better than Crown as a result of good wheel spinning control by additional improvements of the throttle and brake control methods. Especially as the TRAC system controls the brake hydraulic pressure individually for left and right wheel, the car acceleration performance on split-μ surfaces is improved notably.

Eliminating brake squeal generated during brake application is an important task for the improvement of comfort in the vehicle. There has been a lot of research made on the problem of brake squeal in the past. And most of the papers presented elaborate on low frequency brake squeal (2-3kHz). However, brake squeal has often the high-frequency vibration. For this reason, we have made research into the high-frequency brake squeal (5-10kHz). Double-Pulsed Laser Holography is a useful method for visualizing small vibration of brake components during brake squeal generation. The results obtained using Holographic Interferometry show the rotaing disc vibrates in the bending mode with diametral nodes. Consequently, we think that the modification of brake disc can eliminate brake squeal, which is caused by self-excited vibration. Then we have calculated natural frequency and its vibration mode of a circular-plate added mass.

It is very important for the vehicle comfort quality to eliminate brake noise. The brake noise can be defined into two phenomena: One is the high-frequency brake squeal (frequency 1-15kHz), we have presented in 1989 SAE Congress(890864) * (2),and the another is the low-frequency brake groan (frequency 200-500Hz). In this paper,the brake groan has been discussed by constituting the theoretical model,in order to clarify the cause of disc brake groan noise. According to the previous study(3), the groan noise has been occurred by the increase of the disc temperature which has influenced on the disc width and the disc material. On the other hand, the groan noise can be observed in the condition of atmosphere temperature indeed. So that the precise phenomenon and cause should be defined. After observing the groan noise on the test bench, we have constructed the theoretical model and taken the numerical method.

The purpose of this study is to propose braking characteristics that are easy for drivers to handle in a system in which braking and driving operations are performed by hand. Genetic algorithm optimization of braking characteristics showed that the best deceleration tracking was achieved by an FG diagram with a logarithmic function shape. In contrast, the slope of the optimal FG diagram tended to decrease as the driver's proportional gain increased.

The finite element method (FEM) is effective for analyzing brake squeal phenomena. Although FEM analysis can be used to easily obtain squeal frequencies and complex vibration modes, it is difficult to identify how to modify brake structure design or contact conditions between components. Therefore, this study deals with a practical design method using sensitivity analysis to reduce brake squeal, which is capable of optimizing both the structure of components and contact conditions. A series of analysis processes that consist of modal reduction, complex eigenvalue analysis, sensitivity analysis and optimization analysis is shown and some application results are described using disk brake systems.

This paper describes methods to attain a low cost tire pneumatic pressure monitor. We already established two kinds of algorithms for indirect detection of under-inflated tires without requiring any air pressure sensors. One method is to use a disturbance observer and the least mean square method. The other method is to compare the loaded radii of the tires. We have developed an algorithm that reduces the number of calculations needed, while maintaining a relatively small program size, and realized a tire pneumatic pressure monitor that does not require any hardware cost, by incorporating it into the program for the antilock brake system (ABS).

The use of brakes on public roads depends on traffic conditions and the road itself. In order to research into brake usage on various roads and under various conditions, a micro-computer data logging system was developed. The recorded data were analyzed by a large computer and the severity of brake usages was defined. The relationship between the severity and the brake disc rotor temperature was derived, and used to predict brake pad wear/life. The predicted wear coincided fairly clossly with measured wear.

A new concept of an electromagnetic torque converter for hybrid electric vehicles is proposed. The electromagnetic torque converter, which is an electric system comprised of a set of double rotors and a stator, works as a high-efficiency transmission in the driving conditions of low gear ratio including a vehicle moving-off and as a starting device for an internal combustion engine. Moreover, it can be used for an electric vehicle driving as well as for a regenerative braking. In this concept, a high-efficiency drivetrain system for hybrid electric vehicles is constructed by replacing a fluid-type torque converter with the electromagnetic torque converter in the automatic transmission of a conventional vehicle. In this paper, we present the newly developed electromagnetic torque converter with a compact structure that enables mounting on a vehicle, and we evaluate its transmission efficiency by experiment.

Vehicle rollovers are one of the more severe crash modes in the US - accounting for 32% of all passenger vehicle occupant fatalities annually. One design enhancement to help prevent rollovers is Electronic Stability Control (ESC) which can reduce loss of control and thus has great promise to enhance vehicle safety. The objectives of this research were (1) to estimate the effectiveness of ESC in reducing the number of rollover crashes and (2) to identify cases in which ESC did not prevent the rollover to potentially advance additional ESC development. All passenger vehicles and light trucks and vans that experienced a rollover from 2006 to 2015 in the National Automotive Sampling System Crashworthiness Database System (NASS/CDS) were analyzed. Each rollover was assigned a crash scenario based on the crash type, pre-crash maneuver, and pre-crash events.

This paper deals with friction under wet condition in the disk brake system of automobiles. In our previous study, the variation of friction coefficient μ was observed under wet condition. And it was experimentally found that μ becomes high when wear debris contains little moisture. Based on the result, in this paper, we propose a hypothesis that agglomerates composed of the wet wear debris induce the μ variation as the agglomerates are jammed in the gaps between the friction surfaces of a brake pad and a disk rotor. For supporting the hypothesis, firstly, we measure the friction property of the wet wear debris, and confirm that the capillary force under the pendular state is a factor contributing to the μ variation. After that, we simulate the wear debris behavior with or without the capillary force using the particle-based simulation. We prepare the simulation model for the friction surfaces which contribute to the friction force through the wear debris.

Reducing disk brake squeal, especially low frequency disk brake squeal (1-5kHz), is an important technical issue in vehicles. The disk brake squeal mechanism has been shown in many papers (1), (2), (3), (4), (5), (6), (7), (8) and (9). Recently, the disk brake squeal comes to be simulated by Finite Element Analysis (FEA) for disk brake design (10), (11), (12), (13), (14), (15), (16), (17), (18) and (19). Though FEA is useful, it is sometimes difficult to modify in large when the prototype of disk brake system has been designed. First Order Analysis gives design concepts, which should be done before FEA. This paper shows First Order Analysis of low frequency disk brake squeal. The equation of motion is shown in 4 degrees of freedom model. In this equation the generalized force matrix is composed of the variations of pressure and friction force between each brake pad and brake disk. The generalized force matrix is arranged with a symmetric matrix and an anti-symmetric matrix.

For the first time ever, a new hybrid system using a 42-V power supply system has been developed for better fuel economy, lower emissions and urban environment. This paper introduces the system configuration, features and gives actual vehicle evaluation results. This system has a motor generator (hereinafter abbreviated as M/G) connected to the engine crankshaft via a belt, in place of the alternator on a conventional vehicle. The electronic control of the M/G has five functions, 1 restarting the stopped engine, 2 driving the vehicle when starting, 3 driving auxiliaries when the engine is stopped, 4 power generation during ordinary traveling and 5 regenerative braking on deceleration braking. By restarting the engine via a belt with motor driving control, a smooth starting without discomfort is achieved. Furthermore, using this motor to drive auxiliaries during idle increases the number of idle stop opportunities.

To solve various environmental problems, fuel-efficient vehicles that reduce CO2 emissions as well as exhaust gas emissions have been developed. In such vehicles, a regenerative brake is used to further reduce fuel consumption. Because the market size for such vehicles is expanding, a brake system is required that can be used in a wide range of vehicles extending from internal combustion engine vehicles (ICEVs) to electric vehicles (EVs). In addition, issues such as deceleration fluctuation and brake pedal fluctuation arise because the regenerative brake force is dependent on the vehicle speed. This paper presents a brake system configuration and its element technologies that can replace existing brake systems in different vehicles ranging from ICEVs to EVs. The proposed system can realize a regenerative cooperative brake not only by replacing the brake booster unit but also without replacing the modulator.

A new type of torque transmit coupling has recently been developed for 4WD cars, that provides a better match to ABS, is of lighter weight, and uses a simpler operating mechanism. This coupling transmits torque with a multi-disc clutch that is engaged by the pressure of high viscosity silicone oil. The rotary blade generates variably the silicone oil pressure, according to both differential speed and direction of rotation between the front and rear wheels. This coupling provides a good match between 4WD performance and four wheel Anti-lock Braking System (ABS) by a modification of the rotary blade shape. No additional devices are needed. This paper describes the characteristics of this coupling and the in-vehicle performance.