Search Results

The wear mechanisms of the methanol engine were studied using dynamometer tests. Formic acid from methanol combustion mixes with the lubricant oil and attacks the metal surfaces. The iso tacho prorissis method was successfully applied to analyze the formic acid content of the used oil. A large amount of condensed water is also formed by methanol combustion and accelerates the wear. Wear can be effectively reduced by shortening lubricant oil change intervals, by using a special oil and by durable surface treatment of engine parts.

Finite element aodels have been developed to analyze drive line and suspension vibration. For the analysis of booming noise, we have addressed the optimization of the differential gear carrier mounting system by using a virtual system and realization of it considering many constraints. To reduce the differential whine noise, a simulation method considering the transmitting error of the differential gear was applied. And we have approached for the subtle arrangements of many structural resonances with detail research of the drive line and suspension. For the reduction of road noise, we adopted the approach of shifting the node of the rear suspension member mode.

To prevent global warming, further reductions in carbon dioxide are required. It is therefore important to promote the spread of electric vehicles powered by internal combustion engines and electric vehicles without internal combustion engines. As a result, emissions from hybrid electric vehicles equipped with internal combustion engines should be further reduced. Interest in catalytic reactions in an electric field with a higher catalytic activity compared to conventional catalysts has increased because this technology consumes less energy than other electrical heating devices. This study was therefore undertaken to apply a catalytic reaction in an electric field to an exhaust emission control. First, the original experimental equipment was built with a high voltage system used to conduct catalytic activity tests.

The automobile industry currently faces many challenges which may greatly impact on its foundry operations. One of these challenges, consumers'' demand for greater fuel efficiency, can be met by reducing the weight of castings used in automobiles, and minimizing engineering tolerances. In answer to this particular demand, engine foundries have begun to either produce cylinder blocks or other castings with aluminum rather than cast iron. However, if a reduction in weight (thin wall and near-net shaping) can be realized with cast iron, there would be numerous merits from the perspective of cost and compactness and there would be much more flexibility in automotive parts design.

This research developed a new measurement technology for thermal analysis of the heat radiation from a hybrid transaxle case surface to the air and improved the heat radiation performance. This heat flux measurement technology provides the method to measure heat flux without wiring of sensors. The method does not have effects of wiring on the temperature field and the flow field unlike the conventional methods. Therefore, multipoint measurement of heat flux on the case surface was enabled, and the distribution of heat flux was quantified. To measure heat flux, thermal resistances made of plastic plates were attached to the case surface and the infrared thermography was used for the temperature measurement. The preliminary examination was performed to confirm the accuracy of the thermal evaluation through heat flux measurement. The oil in the transaxle was heated and the amount of heat radiation from the case surface was measured.

At the engine restart, when the temperature of the catalytic converter is low, additional fuel consumption would be required to warm up the catalyst for controlling exhaust emission.The aim of this study is to find a thermally optimal way to reduce fuel consumption for the catalyst warm up at the engine restart, by improving the thermal retention of the catalytic converter in the cool down process after the previous trip. To make analysis of the thermal flow around the catalytic converter, a 2-D thermal flow model was constructed using the thermal network method. This model simulates the following processes: 1) heat conduction between the substrate and the stainless steel case, 2) heat convection between the stainless steel case and the ambient air, 3) heat convection between the substrate and the gas inside the substrate, 4) heat generation due to chemical reactions.

In recent years, the demand for high-speed/high-bandwidth communication for in-vehicle networks has been increasing. This is because the usage of high-resolution screens and high-performance rear seat entertainment (RSE) systems is expanding. Additionally, it is also due to the higher number of advanced driver assistance systems (ADAS) and the future introduction of autonomous driving systems. High-volume data such as high definition sensor images or obstacle information is necessary to realize these systems. Consequently, automotive Ethernet, which meets the requirements for high-speed/high-bandwidth communication, is attracting a lot of attention. The application of automotive Ethernet to in-vehicle networks requires that technology developments satisfy EMC performance requirements. In-vehicle EMC requirements consist of two parts: emission and immunity. The emission requirement is to restrict the electromagnetic noise emitted from vehicle.

The combustion chamber deposit (CCD) forming tendency of gasoline components and detergents were investigated with laboratory tests ad engine dynamometer tests. In the dynamometer tests, the driving conditions under which fuels and detergents influence CCD formation were specified, and the effects of different gasoline components and detergent blends on CCD formation were examined. In the laboratory tests, the CCD forming process was investigated thoroughly [10]. The CCD forming tendency of aromatic compounds in gasoline were dependent not only on physical properties such as molecular weight, but also chemical structure (number or position of the alkyl substituents of aromatic molecules). As for oxygenates, engine dynamometer tests with MTBE blended gasoline yielded less CCD than the test without MTBE. The CCD forming tendency of detergents correlated with the thermal decompositon tendency of the detergent package and the concentration of the main agents.

The potential of high efficiency zero-emission engines fueled by hydrogen, which is regarded as a promising form of energy for the future, is being researched. The argon circulated hydrogen engine [ 1 ] is one system theoretically capable of achieving both high efficiency and zero emissions, and its feasibility for use in vehicles has been studied. Specifically, tests were performed to verify the following issues. It was examined whether stable hydrogen combustion could be achieved under an atmosphere of argon and oxygen, which has a high specific heat ratio, and whether the substantial thermal efficiency improvement effect of the argon working gas could be achieved. An argon circulation system was also studied whereby steam, which is the combustion product of the hydrogen and oxygen emitted from the engine, is separated by condensation to enable the remaining argon to be re-used.

This paper describes application of sintered silicon nitride to the swirl lower-chamber in order to improve performance of turbocharged diesel engines. Various stress analyses by finite element method and stress measurements have been applied to determine the design specifications for the component, which compromise brittleness of ceramic materials. Material development was conducted to evaluate strength, fracture toughness, and thermal properties for the sintered bodies. Ceramic injection molding has been employed to fabricate components with large quantities in the present work. Quality assurance for the components can be made by reliability evaluation methods as well as non-destructive and stress loading inspections. It is found that the engine performance with ceramic component has been increased in the power out put of 9PS as compared to that of conventional engines.

Ongoing research on active stabilizers involves not only control of the roll angle of the vehicle based on steering input but also improving ride comfort by reducing roll vibration caused by the antiphase road surface input. In that context, roll skyhook control, which applies skyhook theory to provide feedback on the vehicle roll and drive the actuators, has already been presented. Although vibration in all frequency bands can be reduced if there is no control delay, time lags or phase delays in control elements such as the communication, computation, low-pass filter, or actuators can amplify vibration. Consequently, a sufficient effect of controlling cannot be obtained. This paper will address wheelbase filtering, which produces a frequency that minimizes roll oscillation, and is used to suppress the influence of the undesirable vibration.

The compression ratio and expansion ratio are fundamental parameters that determine the thermal efficiency of an SI engine, and the potential of setting these ratios to arbitrary values was studied as a way of improving engine efficiency. First, the efficiency resulting from different compression and expansion ratios was calculated from a theoretical formula. As a result, it was verified that a 20% improvement in thermal efficiency could be expected by adopting a super-high expansion ratio of 20 or higher, which is an extremely large value for an SI engine, while keeping the compression ratio within a range that can ensure appropriate combustion. Subsequently, this research calculated the possibility of improving engine efficiency under a condition that constrains the swept volume to a constant value in consideration of practicability.

This research proposes an automatic measuring method for the impulse noise of the valve system in engine production line. This research is composed of the following two parts. (1) The most suitable method for indicating the impulse noise of the valve system - the representative characteristic values - is selected from the general measuring methods for impulse noise. As the result, the crest factor in the frequency band above 1kHz became optimal. (2) By detailed sensory characteristic analysis it was found that impulse noise can be heard better with increasing frequency and that there is little influence in the frequency band with the same frequency as the background noise. Thus the crest factor was obtained for each frequency, and the sensory test for the impulse noise of the valve system is deduced by this linear coupling. As the result of multiple reguression analysis, a high accuracy prediction equetion with a multiple correlation coefficient of 0.91 has been obtained.

A new stratified charge combustion system has been developed for direct injection gasoline engines. The special feature of this system is employment of a thin fan-shaped fuel spray formed by a slit nozzle. The stratified mixture is produced by the combination of this fan-spray and a shell-shaped piston cavity. Both under-mixing and over-mixing of fuel in the stratified mixture is reduced by this system. This combustion system does not require distinct charge motion such as tumble or swirl, which enables intake port geometry to be simplified to improve full load performance. The effects of the new system on engine performance at part load are improved fuel consumption and reduced smoke, CO and HC emissions, obviously at medium load and medium engine speed. HC emissions at light load are also improved even with high EGR conditions.

Periodic regeneration of the diesel particulate trap is essential to maintain the collection efficiency and exhaust gas hack pressure at acceptable levels. The objectives of this study are to describe the phenomenology of ceramic foam filter regeneration process and to present its mathematical model. Further simulation study is carried out to estimate the effects of various factors including fuel additive on the ignition and the filter bed temperature and to investigate conditions of excessive temperature which could result in filter destruction. The model is based on the assumption that the regeneration process is composed of two steps. The first step is the additional heat supply from the external energy source, and the second step is the spontaneous combustion propagation. The results from the analytical model agreed very well with the experimental results.

Two-layered surface materials composed of a thermoplastic olefin elastomer (TPO) skin and a cross-linked polypropylene (PP)foam are increasingly replacing the conventional PVC skin/PVC foam for interior trims. In the past, recycled material obtained by melt-blending TPO skin and PP foam could not be re-used for TPO skin because of its appearance. A new recycling technology using the reaction biaxial extruder with a reaction agent can decompose the network structure of PP foam. As a result, PP foam is dispersed into TPO uniformly and the recycled material has properties and an appearance similar to virgin TPO. These new properties may allow the application of the recycled material as a surface material.

The structure of HCCI (homogeneous charge compression ignition) combustion flames was quantitatively analyzed by measuring the two-dimensional gas temperature distribution using phosphor thermometry. It was found from the relation between a turbulent Reynolds number and Karlovitz number that, when compared with the flame propagation in an S.I. engine, HCCI combustion has a wider flame structure with respect to the turbulence scale. As a result of our experimentation for the influence of low temperature reaction (LTR) using two types of fuel, it was also confirmed that different types of fuel produce different histories of flame kernel structure.

The colour painting of polypropylene bumpers has required development of a new polypropylene surface treatment which provides improved adhesion of the paint film to polypropylene. According to the results of various improvement studies on the application of plasma treatment, it has been discovered that surface treatment by means of plasma of an oxygen and nitrogen gas mixture activated by microwave (2,450 MHz) provides a remarkable improvement in adhesion. Furthermore, establishing a technique to diffuse plasma effectively within the treatment chamber has enabled a uniform surface treatment of several polypropylene bumpers formed in large and complicated shapes.

ϵ-caprolactam was polymerized in the interlayer space of montmorillonite, the clay mineral yielding a nylon-clay hybrid (NCH). X-ray and TEM measurements revealed that each template of the silicate, which was 1 nm thick, was dispersed in the nylon 6 matrix, and that the interlayer distance of clay increased continuously from 1.2 nm for the unintercalated material to 21.4 nm for the intercalated material. Thus, NCH is a polymer-based molecular composite or a nano-composite. NCH contains 1-15 vol% of monolayer clay. Injection-molded NCH showed excellent mechanical properties compared with nylon 6 in terms of tensile strength, tensile modulus and heat resistance. The tensile modulus of NCH was twice that of Nylon 6, and the heat distortion temperature increased from 65°C for nylon 6 to 145°C for the NCH containing only 1.6 vol% of a clay mineral. It was found that such excellent properties of an NCH system was due to the strong ionic interaction between nylon 6 and the silicate layer.

This paper presents the numerical simulation method to predict the deactivation process of three-way catalytic converters. Three-way catalytic converter's deactivation typically results from thermal and chemical mechanisms. The major factor of thermal deactivation is the sintering of noble metal particles, which is known to depend on the ageing temperature and the oxygen concentration in the exhaust gas. The chemical deactivation is mainly caused by the poisoning, which has two effects on the catalyst deactivation. One effect is the loss of the catalyst activity, which is expressed by reduced frequency factors of reaction rates. Another effect is the suppression of the noble metal sintering. Poison deposits prevent the noble metal particles from moving in the washcoat, assisted by the reduced thermal loading of reaction heats, which is caused by the loss of the catalyst activity. Modeling these deactivation factors, we propose the rate expression of noble metal sintering.