Search Results

This paper discusses the development of the 1997 Jeep Cherokee model for the National Advanced Driving Simulator's planned vehicle dynamics software, NADSdyna. Recursive rigid body formalism called the Real Time Recursive Dynamics (RTRD) developed by the University of Iowa is used to model the front and rear suspension mechanisms. To complement vehicle dynamics for simulator applications, subsystems that include tires, aerodynamics, powertrain, brake, and steering are added to the rigid body dynamics model. These models provide high fidelity driving realism to simulate severe handling maneuvers in real time. The soundness of the model does not only depend on the mathematics of the model, but also on the validity of the parameters. Therefore, this paper discusses thoroughly the methodology of parameters estimation. A generic model of cruise control is included.

The paper discusses the development of a vehicle dynamics model and model validation of the 2003 Ford Expedition in CarSim. The accuracy of results obtained from simulations depends on the realism of the model which in turn depends on the measured data used to define the model parameters. The paper describes the tests used to measure the vehicle data and also gives a detailed account of the methodology used to determine parameters for the CarSim Ford Expedition model. The vehicle model was validated by comparing simulation results with experimental testing. Bounce and Roll tests in CarSim were used to validate the suspension and steering kinematics and compliances. Field test data of the Sine with Dwell maneuver was used for the vehicle model validation. The paper also discusses the development of a functional electronic stability control system and its effect on vehicle handling response in the Sine with Dwell maneuver.

This paper presents an evaluation of a vehicle dynamics model intended to be used for the National Advanced Driving Simulator (NADS). Dynamic validation for high performance simulation is not merely a comparison between experimental and simulation plots. It involves strong insight of vehicle's subsystems mechanics, limitations of the mathematical formulations, and experimental predictions. Lateral, longitudinal, and ride dynamics are evaluated using field test data, and analytical diagnostics. The evaluation includes linear and non-linear range of vehicle dynamics response.

This paper discusses dry stopping performance comparisons of various foundation brake systems on Class-8 truck tractors (having a GVWR greater than 33,000 lbs.). For these studies, four configurations of foundation brakes were fitted to two modern 6x4 conventional truck tractors without modification to the control, application, or ABS systems. Foundation brakes compared include standard S-cam drum brakes on all six positions, high-output S-cam drum and then air disc brakes on the steer axles, and air disc brakes on all six brake positions. Discussions include analyses of stopping distance from 60 mph (96.6 kph) for all test conditions. The truck tractors were tested in two weight configurations, LLVW (i.e., bobtail) and GVWR (50,000 lbs. total axle weight, using an unbraked control semitrailer).

As Intelligent Transportation Systems (ITS) become more prevalent, the need to archive data from field tests becomes more critical. These data can guide the design of future systems, provide an information conduit among the many developers of ITS, enable comparisons across locations and time, and support development of theoretical models of driver behavior. The National Highway Traffic Safety Administration (NHTSA) is interested in such an archive. While a design for an ITS data archive has not yet been developed, NHTSA has supported the enhancement of the Test Planning, Analysis, and Evaluation System (Test PAES), originally developed by Calspan SRL Corporation for the U. S. Air Force Armstrong Laboratory, for possible use in such an archive. On a single screen, Test PAES enables engineering unit data, audio, and video, as well as a vehicle animation, to be time synchronized, displayed simultaneously, and operated with a single control.

Development of improved dummy lower extremities which are compatible with both the Hybrid III design and with other advanced torso designs is continuing. The first task was to establish the design and performance requirements for these new crash dummy components. To achieve this, an extensive literature review of relevant biomechanical studies was carried out and a detailed accident investigation of crashes involving lower extremity injury was performed. Finally, detailed discussions were conducted with biomechanical and clinical experts. The innfromation gained through these efforts was synthesized into a detailed set of design goals and requirements for the improved lower extremities, which are summarize in this paper.

In crashes between heavy trucks and light vehicles, most of the fatalities are the occupants of the light vehicle. A reduction in heavy truck stopping distance should lead to a reduction in the number of crashes, the severity of crashes, and consequently the numbers of fatalities and injuries. This study made use of the National Advanced Driving Simulator (NADS). NADS is a full immersion driving simulator used to study driver behavior as well as driver-vehicle reactions and responses. The vehicle dynamics model of the existing heavy truck on NADS had been modified with the creation of two additional brake models. The first was a modified S-cam (larger drums and shoes) and the second was an air-actuated disc brake system. A sample of 108 CDL-licensed drivers was split evenly among the simulations using each of the three braking systems. The drivers were presented with four different emergency stopping situations.

In 2004, a model of a 6s6m ABS controller was developed in order to support NHTSA's efforts in the study of heavy truck braking performance. This model was developed using Simulink and interfaced with TruckSim, a vehicle dynamics software package, in order to create an accurate braking simulation of a 6×4 Peterbilt straight truck. For this study, the vehicle model braking dynamics were improved and the ABS controller model was refined. Also, the controller was made adaptable to ABS configurations other than 6s6m, such as 4s4m and 4s3m. Controller models were finally validated to experimental data from the Peterbilt truck, gathered at NHTSA's Vehicle Research and Test Center (VRTC).

This paper presents a real-time steering system torque feedback model used in the National Advanced Driving Simulator (NADS). The vehicle model is based on real-time recursive multi-body dynamics augmented with vehicle subsystems models including tires, power train, brakes, aerodynamics and steering. The steering system feel is of paramount importance for the fidelity of the simulator. The driver has to feel the appropriate torque as he/she steers the vehicle. This paper presents a detailed mathematical model of the steering physics from low-speed stick-slip to high-speed states. On-center steering weave handling and aggressive lane change inputs are used to validate the basic mathematical predictions. This validation is objective and open loop, and was done using field experiments.

This paper presents an evaluation of a complete vehicle dynamics model for a 1997 Jeep Cherokee to be used for the National Advanced Driving Simulator. Vehicle handling and powertrain dynamics are evaluated and simulation results are compared with experimental field-testing. NADSdyna, the National Advanced Driving Simulator vehicle dynamics software, is used. The Jeep evaluation covers vehicle directional dynamics that include steady state, transient and frequency response, and vehicle longitudinal dynamics that include acceleration and braking.

There exists a fairly extensive set of tire force measurements performed on dry pavement. But in order to develop a low-coefficient of friction tire model, a set of tire force measurements made on wet pavement is required. Using formulations and parameters obtained on dry roads, and then reducing friction level to that of a wet road is not sufficient to model tire forces in a high fidelity simulation. This paper describes the process of more accurately modeling low coefficient tire forces on the National Advanced Driving Simulator (NADS). It is believed that the tire model improvements will be useful in many types of NADS simulations, including ESC and other advanced vehicle technology studies. In order to produce results that would come from a road surface that would be sufficiently slippery, a set of tires were shaved to 4/32 inches and sent to a tire-testing lab for measurement.

This paper describes ongoing research conducted by the National Highway Traffic Safety Administration (NHTSA) to evaluate the potential of safety restraints on large school buses. School bus transportation is one of the safest forms of transportation in the United States. Large school buses provide protection because of their visibility, size, and weight, as compared to other types of motor vehicles. Additionally, they are required to meet minimum Federal Motor Vehicle Safety Standards (FMVSS) mandating compartmentalized seating, emergency exits, roof crush and fuel system integrity, and minimum bus body joint strength.

To address the limitations of traditional data acquisition systems, The National Highway Traffic Safety Administration (NHTSA) has developed a system called the Micro Data Acquisition System (Micro-DAS). The system is very small and can be installed into a variety of vehicles in a short time period. It's video recording system is capable of collecting over 22 hours of full-motion video and data acquisition is triggered based on user created events. Using these features the system allows information on driver behavior and performance, vehicle performance, and roadway environments to be recorded in-situ, ensuring real world data collection without concerns associated with vehicle familiarity or researcher presence.

This paper presents the implementation and performance of an electric all-wheel drive system on a series-parallel, through-the-road hybrid electric vehicle. Conventional methods of all-wheel drive do not provide a suitable solution for this type of vehicle as the powertrain lacks a mechanical link between the front and rear axles. Moreover, this unique architecture allows the vehicle to be propelled solely by the front, or the rear, wheels during typical operation. Thus, the algorithm presented here manages wheel slip by either the front, or rear wheels when engaging to provide all-wheel drive capability. necessary testing validates the robustness of this Extensive system.

The state of Ohio has recognized the importance and potential impact of Intelligent Vehicle-Highway Systems (IVHS) to its citizens and business enterprises. In response to the identified need, a small group of individuals representing Federal and state government, academia, and the private sector have worked together over the past year to initiate a statewide IVHS effort. This initiative is referred to as IVHS~Ohio. The objective of the effort is to "coordinate and foster a public, private, and academic partnership to make the urban and rural surface transportation system in the state of Ohio significantly safer, more effective, and more efficient by accelerating the identification, development, integration, and deployment of IVHS technologies." A May 1993 symposium was attended by over 220 people from government, academia, and the private sector. The result was a unanimous decision to establish a statewide IVHS program.

This paper discusses techniques for estimating steering feel performance measures for on-center and off-center driving. Weave tests at different speeds are used to get on-center performances for a 1994 Ford Taurus, a 1998 Chevrolet Malibu, and a 1997 Jeep Cherokee. New concepts analyzing weave tests are added, specifically, the difference of the upper and lower curves of the hysteresis and their relevance to driver load feel. For the 1997 Jeep Cherokee, additional tests were done to determine steering on-center transition properties, steering flick tests, and the transfer function of handwheel torque feel to handwheel steering input. This transfer function provides steering system stiffness in the frequency domain. The frequency domain analysis is found to be a unique approach for characterizing handwheel feel, in that it provides a steering feel up to maximum steering rate possible by the drivers.

Several thoracic and head protection side impact air bag systems (SAB) are emerging in the U.S. market and are projected to become prevalent in the fleet. These systems appear to offer superior protection in side crashes. However, concerns have been raised as to their potential for causing injury to out-of-position (OOP) occupants. This paper describes the National Highway Traffic Safety Administration (NHTSA) program for evaluation of the SAB systems for OOP occupants and provides a status report on the current research. The industry's Side Airbag Out-of- Position Injury Technical Working Group (TWG) recommended procedures for 3-year-old and 6-year-old occupants are evaluated. Additional test procedures are described to augment the TWG procedures for these occupants and 12-month- old infants.

This paper covers research conducted at the National Highway Traffic Safety Administration's Vehicle Research and Test Center (VRTC) examining the performance of semitrailer anti-lock braking systems (ABS). For this study, a vehicle dynamics model was constructed for the combination of a 4×2 tractor and a 48-foot trailer, using TruckSim. ABS models for the tractor and trailer, as well as brake dynamics and surface friction models, were created in Simulink so that the effect of varying ABS controller parameters and configurations on semitrailer braking performance could be studied under extreme braking maneuvers. The longitudinal and lateral performances of this tractor-trailer model were examined for a variety of different trailer ABS controller models, including the 2s1m, 4s2m, and 4s4m configurations. Also, alternative controllers of the same configuration were studied by varying the parameters of the 2s1m controller.

Sixty test participants each drove an instrumented vehicle over a prescribed route that included highway and city street segments. Drivers included equal numbers of males and females, and equal numbers of individuals in Younger (18 to 25 years of age), Middle (35 to 45 years of age), and Older (55 to 65 years of age) age groups. Test participants drove on weekdays (Monday through Thursday), in good weather, and during both rush and non-rush hour morning or afternoon periods. Approximately 6,600 vehicle miles of travel on public roads were recorded. Car following range and range rate, travel speed, and driver eye glances were measured to examine driver eye glance behavior during car following. Results indicate the conditions in car following when drivers looked away from the road ahead, the distribution of glance durations when looking away, and the distribution of where drivers looked away from the road ahead.

In support of NHTSA's studies of heavy truck brake types and their effects on vehicle stopping performance and stability, the NHTSA Vehicle Research and Test Center (VRTC) has evaluated four foundation brake types on their Greening Brake Dynamometer. Several sample assemblies of each type of brake were tested to better understand variability. Braking tests were run under the “Laboratory Test Procedure for FMVSS 121D Air Brake Systems - Dynamometer” (TP- 121D-01) procedures. Afterward, the test scope was expanded to include higher speeds and higher severity conditions than those specified Test Procedure. This paper reports on the differences in braking effectiveness between two traditional S-Cam air brake types and two recently introduced Air Disc brake types. Burnish procedure trends are briefly discussed and compared. Responses of the pneumatic brakes to both constant-pressure and dynamic inputs are also compared and discussed.