Search Results

The U.S. Army currently uses JP-8 for global operations according to the ‘one fuel forward policy’ in order to reduce the logistics burden of supplying a variety of fuels for given Department of Defense ground vehicle applications. One particular challenge with using global JP-8 is the lack of or too broad a range of specified combustion affecting properties including ignition quality, high temperature viscosity, and density. In particular, the ignition quality of JP-8 has dramatically varied throughout the past decade on a global basis covering a range of 29 to 70 cetane index. This key combustion affecting parameter was explored in this study by evaluating a synthesized low ignition quality jet fuel blended in 25% volumetric proportions with JP-8 to effectively cover a cetane number range of 25 to 45 in a single cylinder diesel engine operated at various light, medium, and high load operating conditions.

With the drive to reduce emissions and improve fuel economy, fuel injection pressures have increased. This has increased Hertzian stresses on the roller follower cam system to the point that cam lobe contact fatigue failure has become the “Achilles heel” of diesel engine durability in the 1990s. Contact fatigue failures have occurred on both injector lobes and the exhaust and inlet lobes. This is particularly the case in fleets with frequent engine shut downs and starts, stop-go service and in some line-haul fleets. This paper describes field service cam failures across several engine types and applications. In our experience supporting fleet customers in cam failure analysis, we found that a combination of ten critical independent variables must be correct in order to prevent cam lobe contact fatigue failures. These variables are each discussed separately.

Conventional diesel fuel has been in the market for decades and used successfully to run diesel engines of all sizes in many applications. In order to reduce emissions and to foster energy source diversity, new fuels such as alternative and renewable, as well as new fuel formulations have entered the market. These include biodiesel, gas-to-liquid, and alternative formulations by states such as California. Performance variations in fuel economy, emissions, and compatibility for these fuels have been evaluated and debated. In some cases contradictory views have surfaced. “Sustainable”, “Renewable”, and “Clean” designations have been interchanged. Adding to the confusion, results from one fuel in one type of engine such as an older heavy-duty engine, is at times compared to that of another type such as a modern light-duty. This study was an attempt to compare the performance of several fuels in an identical environment, using the same engine, for direct comparison.

Conventional diesel fuel has been in the market for decades and used successfully to run diesel engines of all sizes in many applications. In order to reduce emissions and to foster energy source diversity, new fuels such as alternative and renewable, as well as new fuel formulations have entered the market. These include biodiesel, gas-to-liquid, and alternative formulations by states such as California. Performance variations in fuel economy, emissions, and compatibility for these fuels have been evaluated and debated. In some cases contradictory views have surfaced. “Sustainable”, “Renewable”, and “Clean” designations have been interchanged. Adding to the confusion, results from one fuel in one type of engine such as an older heavy-duty engine, is at times compared to that of another fuel in another type such as a modern light-duty engine. This study was an attempt to compare the performance of several fuels in identical environments, using the same engine, for direct comparison.

Experiments were performed to measure the number-weighted particle size distributions emitted from a gasoline direct injection (GDI) engine. Measurements were made on a late model vehicle equipped with a direct injection spark ignition engine. The vehicle was placed on a chassis dynamometer, which was used to load the engine to road load at five different vehicle speeds ranging from 15 - 100 km/hr. Dilution of the exhaust aerosol was carried out using a two-stage dilution system in which the first stage dilution occurs as a free jet. Particle size distributions were measured using a TSI 3934 scanning mobility particle sizer. Generally speaking, the presence of the additives did not have a strong, consistent influence on the particle emissions from this engine. The polyether amine demonstrated a reduction in particle number concentration as compared to unadditized base fuel.

The US Army is currently seeking to reduce fuel consumption by utilizing fuel efficient lubricants in its ground vehicle fleet. An additional desire is for a lubricant which would consist of an all-season (arctic to desert), fuel efficient, multifunctional Single Common Powertrain Lubricant (SCPL) with extended drain capabilities. To quantify the fuel efficiency impact of a SCPL type fluid in the engine and transmission, current MIL-PRF-46167D arctic engine oil was used in place of MIL-PRF-2104G 15W-40 oil and SAE J1321 Fuel Consumption In-Service testing was conducted. Additionally, synthetic SAE 75W-140 gear oil was evaluated in the axles of the vehicles in place of an SAE J2360 80W-90 oil. The test vehicles used for the study were three M1083A1 5-Ton Cargo vehicles from the Family of Medium Tactical Vehicles (FMTV).

The US Army is currently assessing the feasibility and defining the requirements of a Single Common Powertrain Lubricant (SCPL). This new lubricant would consist of an all-season (arctic to desert), fuel-efficient, multifunctional powertrain fluid with extended drain capabilities. As a developmental starting point, diesel engine testing has been conducted using the current MIL-PRF-46167D arctic engine oil at high temperature conditions representative of desert operation. Testing has been completed using three high density military engines: the General Engine Products 6.5L(T) engine, the Caterpillar C7, and the Detroit Diesel Series 60. Tests were conducted following two standard military testing cycles; the 210 hr Tactical Wheeled Vehicle Cycle, and the 400 hr NATO Hardware Endurance Cycle. Modifications were made to both testing procedures to more closely replicate the operation of the engine in desert-like conditions.

This paper presents a new approach for the development of six different JP-8 surrogates for application in diesel cycle simulation. The approach involves a step-wise formulation of 2-, 3-, and 4-component surrogates from a list of pure compounds which are selected based on several criteria. A MATLAB code is developed and is used in conjunction with the Ignition Quality Tester (IQT) and HYSYS software in order to formulate optimal surrogates. The first part of the results shows a comparison between the calculated and the measured DCNs for six surrogates. The differences in the properties such as the density, volatility, lower heating value, H/C ratio, molecular weight, and threshold sooting index of the surrogates and the JP-8 are also highlighted. This is followed by the evaluation of the surrogates with respect to the target JP-8 fuel. The evaluation is made in terms of ignition delays and the rate of heat release at three different IQT test temperatures.

Over the past several years, economic pressures have driven fleets to substantially increase their maintenance intervals. To meet this challenge, both the Original Equipment Manufacturers (OEMs) and the lubricant suppliers have developed new and better products to give fleet users the benefits of extended service intervals, while at the same time maintaining equipment life and providing the potential for reduced operating costs. Through the selection of proper lubricants, fleets can now minimize their total operating costs with products that meet the OEM extended service specifications, have demonstrated equipment durability, and are formulated using base oil and additive components to minimize the cost of the lubricant. This paper will examine the options available for formulating extended drain transmission and axle lubricants. It will explore the selection of the lubricant base oil as well as the additive system.