Search Results

This paper presents an experimental study on a 2-stroke SI engine, used on small portable tools for gardening or agriculture, aimed to identify possible correlations between parameters related to ionization current and air/fuel mixture richness, considering different fuels and spark plug wear. This, to realize a simple system to control the engine parameters and adapt them to engine aging and fuel type changing. The engine was fed with commercial gasoline, low octane number gasoline, alkylate gasoline and a blend of 80% gasoline and 20% ethanol. In all tests carried out with varying engine speed and spark advance the ionization signal was characterized by a single peak, resulting in the impossibility of distinguishing chemical and thermal ionization. All data collected were analyzed looking for correlations between all the available data of CO emissions and several characteristic parameters obtained from the ionization signal.

In the recent years, the interest in heavy-duty engines fueled with Compressed Natural Gas (CNG) is increasing due to the necessity to comply with the stringent CO2 limitation imposed by national and international regulations. Indeed, the reduced number of carbon atoms of the NG molecule allows to reduce the CO2 emissions compared to a conventional fuel. The possibility to produce synthetic methane from renewable energy sources, or bio-methane from agricultural biomass and/or animal waste, contributes to support the switch from conventional fuel to CNG. To drive the engine development and reduce the time-to-market, the employment of numerical analysis is mandatory. This requires a continuous improvement of the simulation models toward real predictive analyses able to reduce the experimental R&D efforts. In this framework, 1D numerical codes are fundamental tools for system design, energy management optimization, and so on.

Internal combustion engines for vehicle propulsion are more and more sophisticated due to increasingly restrictive environmental regulations. In case of heavy-duty engines, Compressed Natural Gas (CNG) fueling coupled with Three-Way Catalyst (TWC) and Exhaust Gas Recirculation (EGR) can help in meeting the imposed emission limits and preventing from thermal stress of engine components. To cope with the new issues associated with the more complex hardware and to improve powertrain performance and reliability and after-treatment efficiency, the engine control strategies must be reformulated. The paper focuses on the steady-state optimization of control parameters for a heavy-duty engine fueled by CNG and equipped with turbocharger and EGR. The optimization analysis is carried out to design EGR, spark timing and wastegate control, aimed at increasing fuel economy while reducing in-cylinder temperature to prevent from thermal stress of engine components.

In this paper, a high performance V12 spark-ignition engine is experimentally investigated at test-bench in order to fully characterize its behavior in terms of both average parameters, cycle-by-cycle variations and knock tendency, for different operating conditions. In particular, for each considered operating point, a spark advance sweep is actuated, starting from a knock-free calibration, up to intense knock operation. Sequences of 300 consecutive pressure cycles are measured for each cylinder, together with the main overall engine performance, including fuel flow, torque, and fuel consumption. Acquired data are statistically analyzed to derive the distributions of main indicated parameters, in order to find proper correlations with ensemble-averaged quantities. In particular, the Coefficient of Variation (CoV) of IMEP and of the in-cylinder peak pressure (pmax) are correlated to the average combustion phasing and duration (MFB50 and Δθb), with a good coefficient of determination.

The improvement in engines efficiency and reduction of emissions is the permanent aim of engine industry in order to meet European standards regulation. To optimize small internal combustion engines it is necessary to improve the basic knowledge of thermo-fluid dynamic phenomena occurring during the combustion. This paper describes the combustion process in an optically accessible two-stroke spark-ignition engine used in a commercial 43 cm3 chainsaw. Two different feeding systems were tested: standard and CWI one. The engine head was modified in order to allow the visualization of the combustion using endoscopic system coupled with a high spatial resolution ICCD camera. Flame front propagation was evaluated through an image processing procedure. The image visualization and chemiluminence allowed to follow the combustion process from the spark ignition to the exhaust phase at high engine speed. All the optical data were correlated with engine parameters and exhaust emissions.

Modern VVA systems offer new potentialities in improving the fuel consumption for spark-ignition engines at low and medium load, meanwhile they grant a higher volumetric efficiency and performance at high load. Recently introduced systems enhance this concept through the possibility of concurrently modifying the intake valve opening, closing and lift leading to the development of almost "throttle-less" engines. However, at very low loads, the control of the air-flow motion and the turbulence intensity inside the cylinder may require to select a proper combination of the butterfly throttling and the intake valve control, to get the highest BSFC (Brake Specific Fuel Consumption) reduction. Moreover, a low throttling, while improving the fuel consumption, may also produce an increased gas-dynamic noise at the intake mouth. In highly "downsized" engines, the intake valve control is also linked to the turbocharger operating point, which may be changed by acting on the waste-gate valve.

The technique of liquid Water Injection (WI) at the intake port of downsized boosted SI engines is a promising solution to improve the knock resistance at high loads. In this work, an existing 1D engine model has been extended to improve its ability to simulate the effects of the water injection on the flame propagation speed and knock onset. The new features of the 1D model include an improved treatment of the heat subtracted by the water evaporation, a newly developed correlation for the laminar flame speed, explicitly considering the amount of water in the unburned mixture, and a more detailed kinetic mechanism to predict the auto-ignition characteristics of fuel/air/water mixture. The extended 1D model is validated against experimental data collected at different engine speeds and loads, including knock-limited operation, for a twin-cylinder turbocharged SI engine.

The paper deals with experimental testing of a natural gas fueled engine. Break Specific fuel Consumption (BSFC), Average Mass Flow Rate, Instantaneous Cylinder Pressure and some wall temperatures have been measured at some full and part load operating conditions. The results of this experimental activity, still in progress, have been used to calibrate a 1D-flow engine's model. Then the effects of some VVA strategies have been theoretically studied through the validated model. With the aim of maximizing the full load engine's torque, a genetic algorithm was used to calculate the optimized intake and exhaust valves timing angles. Various VVA strategies were compared at part-load in order to reduce brake specific fuel consumption.

In recent years the use of alternative fuels for internal combustion engines has had a strong push coming from both technical and economic-environmental aspects. Among these, gaseous fuels such as liquefied petroleum gas and natural gas have occupied a segment no longer negligible in the automotive industry, thanks to their adaptability, anti-knock capacity, lower toxicity of pollutants, reduced CO2 emissions and cost effectiveness. On the other hand, diesel engines still represent the reference category among the internal combustion engines in terms of fuel consumptions. The possibility offered by the dual fuel systems, to combine the efficiency and performance of a diesel engine with the environmental advantages of gaseous fuels, has been long investigated. However the simple replacement of diesel fuel with natural gas does not allow to optimize the performance of the engine due to the high THC emissions particularly at lower loads.

Hydrogen (H₂) added to natural gas (NG), improves the combustion process of the air-fuel mixture. This gives the potentiality to develop engines with better performance and lower environmental impact. In any case how hydrogen is produced represents a crucial aspect. In general, if H₂ is produced utilizing fossil fuels and not renewable or nuclear sources, the environmental benefit of CO₂ reduction could be reduced. In this paper two engines, a light-duty (LD) and a heavy-duty (HD), were tested in stoichiometric conditions. The engines were fuelled with NG and with two blends of NG with a 20% and a 40% by volume of H₂, respectively named NG/H₂ 20% and NG/H₂ 40%. The light-duty engine was tested at different loads and speeds, with spark advance set by the electronic control unit (ECU). The ECU actuated a retarded ignition, especially at low load. With the heavy-duty engine, the tests were carried out only at high load.

The dual-fuel (diesel/natural gas, NG) concept represents a solution to reduce emissions from diesel engines by using natural gas as an alternative fuel. As well known, the dual-fuel technology has the potential to offer significant improvements in the emissions of carbon dioxide from light-duty compression ignition engines. A further important requirement of the DF operation in automotive engines is a satisfactory response in a wide range of load levels. In particular, the part-load levels could present more challenging conditions for an efficient combustion development, due to the poor fuel/air ratio. Basing on the above assumptions, the authors discuss in this article the results of a combined numerical and experimental study on the effect of different injection timings on performance and pollutant fractions of a common rail diesel engine supplied with natural gas and diesel oil.

In the present paper, two different methodologies are adopted and critically integrated to analyze the knock behavior of a last generation small size spark ignition (SI) turbocharged VVA engine. Particularly, two full load operating points are selected, exhibiting relevant differences in terms of knock proximity. On one side, a knock investigation is carried out by means of an Auto-Regressive technique (AR model) to process experimental in-cylinder pressure signals. This mathematical procedure is used to estimate the statistical distribution of knocking cycles and provide a validation of the following 1D-3D knock investigations. On the other side, an integrated numerical approach is set up, based on the synergic use of 1D and 3D simulation tools. The 1D engine model is developed within the commercial software GT-Power™. It is used to provide time-varying boundary conditions (BCs) for the 3D code, Star-CD™.

The present paper reports 1D and 3D CFD analyses of the air-filter box of a turbocharged VVA engine, aiming to predict and improve the gas-dynamic noise emissions through a partial re-design of the device. First of all, the gas-dynamic noise at the intake mouth is measured during a dedicated experimental campaign. The developed 1D and 3D models are then validated at full load operation, based on experimental data. In particular, 1D model provides a preliminary evaluation of the radiated noise and simultaneously gives reliable boundary conditions for the unsteady 3D CFD simulations. The latter indeed allow to better take into account the geometrical details of the air-filter and guarantee a more accurate gas-dynamic noise prediction. 3D CFD analyses put in evidence that sound emission mainly occur within a frequency range of 350 to 450 Hz.

In the recent years, the interest in heavy-duty engines fueled with Compressed Natural Gas (CNG) is increasing due to the necessity to comply with the stringent CO2 limitation imposed by national and international regulations. Indeed, the reduced number of carbon atoms of the NG molecule allows to reduce the CO2 emissions compared to a conventional fuel. The possibility to produce synthetic methane from renewable energy sources, or bio-methane from agricultural biomass and/or animal waste, contributes to support the switch from conventional liquid fuels to CNG. To drive the engine development and reduce the time-to-market, the employment of numerical analysis is mandatory. This requires a continuous improvement of the simulation models toward real predictive analyses able to reduce the experimental R&D efforts. In this framework, 1D numerical codes are fundamental tools for system design, energy management optimization, and so on.

New internal combustion engines (ICE) are characterized by increasing maximum efficiency, thanks to the adoption of strategies like Atkinson cycle, downsizing, cylinder deactivation, waste heat recovery and so on. However, the best performance is confined to a limited portion of the engine map. Moreover, electric driving in urban areas is an increasingly pressing request, but battery electric vehicles use cannot be easily spread, due to limited vehicle autonomy and recharging issues. Therefore, hybrid propulsion systems are under development, in order to reduce vehicle fuel consumption, by decoupling the ICE running from road load, as well as to permit energy recovery and electric driving. This paper analyses a new-patented solution for power split hybrid propulsion system with gearbox. The system comprises an auxiliary power unit, adapted to store and/or release energy, and a planetary gear set, which is interposed between the ICE and the gearbox.

In this paper, the results of an extensive experimental analysis regarding a twin-cylinder spark-ignition turbocharged engine are employed to build up an advanced 1D model, which includes the effects of cycle-by-cycle variations (CCVs) on the combustion process. Objective of the activity is to numerically estimate the CCV impact primarily on fuel consumption and knock behavior. To this aim, the engine is experimentally characterized in terms of average performance parameters and CCVs at high and low load operation. In particular, both a spark advance and an air-to-fuel ratio (α) sweep are actuated. Acquired pressure signals are processed to estimate the rate of heat release and the main combustion events. Moreover, the Coefficient of Variation of IMEP (CoVIMEP) and of in-cylinder peak pressure (CoVpmax) are evaluated to quantify the cyclic dispersion and identify its dependency on peak pressure position.

Control of knock phenomenon is becoming more and more important in modern SI engine, due to the tendency to develop high boosted turbocharged engines (downsizing). To this aim, improved modeling and experimental techniques are required to precisely define the maximum allowable spark advance. On the experimental side, the knock limit is identified based on some indices derived by the analysis of the in-cylinder pressure traces or of the cylinder block vibrations. The threshold levels of the knock indices are usually defined following an heuristic approach. On the modeling side, in the 1D codes, the knock is usually described by simple correlation of the auto-ignition time of the unburned gas zone within the cylinders. In addition, the latter methodology commonly refers to ensemble-averaged pressure cycles and, for this reason, does not take into account the cycle-by-cycle variations.

This paper reports 1D and 3D CFD analyses aiming to improve the gas-dynamic noise emission of a downsized turbocharged VVA engine through the re-design of the intake air-box device, consisting in the introduction of external or internal resonators. Nowadays, modern spark-ignition (SI) engines show more and more complex architectures that, while improving the brake specific fuel consumption (BSFC), may be responsible for the increased noise radiation at the engine intake mouth. In particular VVA systems allow for the actuation of advanced valve strategies that provide a reduction in the BSFC at part load operations thanks to the intake line de-throttling. In these conditions, due to a less effective attenuation of the pressure waves that travel along the intake system, VVA engines produce higher gas-dynamic noise levels.