Search Results

Sound absorbing materials are commonly compressed when installed in passenger compartments or underhood applications altering the sound absorption performance of the material. However, most prior work has focused on uncompressed materials and only a few models based on poroelastic properties are available for compressed materials. Empirical models based on flow resistivity are commonly used to characterize the complex wavenumber and characteristic impedance of uncompressed sound absorbing materials from which the sound absorption can be determined. In this work, the sound absorption is measured for both uncompressed and compressed samples of fiber and foam, and the flow resistivity is curve fit using an appropriate empirical model. Following this, the flow resistivity of the material is determined as a function of the compression ratio.

Transmission loss (TL) is a good performance measure of mufflers since it represents the muffler's inherent capability of sound attenuation. There are several existing numerical methods, which have been widely used to calculate the TL from numerical simulation results, such as the four-pole and three-point methods. In this paper, a new approach is proposed to evaluate the transmission loss based on the reciprocal work identity. The proposed method does not assume plane wave propagation in the inlet and outlet ducts, and more importantly, does not explicitly apply the anechoic termination impedance at the outlet. As a result, it has the potential of extending TL computation above the plane wave cut-off frequency.

Numerical acoustics has traditionally been relegated to a prediction only role. However, recent work has shown that numerical acoustics techniques can be used to diagnose noise problems. The starting point for these techniques is the acoustic transfer vector (ATV). First of all, ATV's can be used to conduct contribution analyses which can assess which parts of a machine are the predominant noise sources. As an example, the sound power contribution and radiation efficiency from parts of a running diesel engine are presented in this paper. Additionally, ATV's can be used to reliably reconstruct the vibration on a machine surface. This procedure, commonly called inverse numerical acoustics (INA), utilizes measured sound pressures along with ATV's to reconstruct the surface velocity. The procedure is demonstrated on an engine cover for which the reconstructed vibration had excellent agreement with experimental results.

A process for predicting the transmission and insertion losses of multi-component exhaust systems is detailed in this paper. A two-tiered process incorporating boundary element analysis to evaluate multi-component systems is implemented. At the component level, the boundary element method is used to predict the transfer matrix for larger components where plane wave behavior is not expected within the component. The transfer matrix approach is then used to predict insertion loss for built-up systems with interconnecting duct or pipe work. This approach assumes plane wave behavior at the inlet and outlet of each component so it is limited to the low frequency regime. Results are compared with experimental results for HVAC systems.

Carbon nanomaterials such as vertically aligned carbon nanotubes arrays are emerging new materials that have demonstrated superior mechanical, thermal, and electrical properties. The carbon nanomaterials have the huge potential for a wide range of vehicular applications, including lightweight and multifunctional composites, high-efficiency batteries and ultracapacitors, durable thermal coatings, etc. In order to design the carbon nanomaterials for various applications, it is very important to develop effective computational methods to model such materials and structures. The present work presents a structural mechanics approach to effectively model the mechanical behavior of vertically aligned carbon nanotube arrays. The carbon nanotube may be viewed as a geometrical space frame structure with primary bonds between any two neighboring atoms and thus can be modeled using three-dimensional beam elements.

This paper presents the criteria in selecting the size of the tuning capacitor, and the cost tradeoff between magnet volume and tuning capacitor in a free piston Stirling engine power generation system. The permissible range of capacitor size corresponding to different magnet volume, in order to prevent magnet demagnetization and stabilize the operation of the system, is determined. Within the permissible range suitable capacitor size may be selected to compensate the inductive load of the system to improve the overall power factor. If the capacitor size is not in the permissible range, there would exists a danger of losing magnet strength, or unstable operation of the engine that would destroy the engine due to unbounded amplitude of piston oscillations. The theory developed is then applied to a practical system, and the cost tradeoff between magnet volume and capacitor is studied.

In many industries, muffler and silencer design is primarily accomplished via trial and error. Prototypes are developed and tested, or numerical simulation (finite or boundary element analysis) is used to assess the performance. While these approaches reliably determine the transmission loss, designers often do not understand why their changes improve or degrade the muffler performance. Analyses are time consuming and models cannot be changed without some effort. The intent of the current work is to demonstrate how plane wave muffler models can be used in industry. It is first demonstrated that plane wave models can reliably determine the transmission loss for complicated mufflers below the cutoff frequency. Some tips for developing dependable plane wave models are summarized. Moreover, it is shown that plane wave models used correctly help designers develop intuition and a better understanding of the effect of their design changes.

A recently developed superposition approach for determining the insertion loss of a two-inlet muffler is reviewed. To validate the approach, calculated and measured insertion losses are compared for a small engine muffler with two inlets and one outlet. After which, the phasing between the two inputs is varied and the insertion loss is evaluated. Results show that the insertion loss is strongly affected by the phasing between sources at low frequencies while phasing between sources has a lesser impact at high frequencies. At the conclusion of the paper, the theory for applying the superposition approach to transmission loss is reviewed.

It has been shown that the addition of a small amount of nanoparticles into a fluid results in anomalous increase in the thermal conductivity of the mixture, and the resulting nanofluid may provide better overall thermal management and better lubrication in many applications, such as heat transfer fluids, engine oils, transmission fluids, gear oils, coolants and other similar fluids and lubricants. The potential benefits of this technology to the automotive and related industries would be more efficient engines, reduced size and weight of the cooling and propulsion systems, lowered operating temperature of the mechanical systems, and increased life of the engine and other mechanical systems. The new mechanisms for this phenomenon of anomalous thermal conductivity increase have been proposed. The heat transfer properties of a series of graphite nanofluids were presented, and the experimental results were compared with the conventional heat transfer theory for pure liquids.

Over 30 years ago, A. H. Vincent of Westland Helicopters demonstrated that if a structure is excited harmonically, the response at another position (at a fixed frequency) will trace a circle in the complex plane as a result of a dynamic stiffness modification between two points. As either the real or imaginary part of an introduced dynamic stiffness is varied from minus infinity to plus infinity, the structural or acoustic response on any position will map a circle in the complex plane. This paper reviews the basis for this little known principle for vibro-acoustics problems and illustrates the viability for a cantilevered plate example. The applicability of the method is then considered for strictly acoustic systems like intake and exhaust systems. Specifically, it is shown that the response traces a circle in the complex plane if either the real or imaginary parts of the source or termination impedance are varied from minus to plus infinity.

Techniques and problems associated with truck exhaust system noise measurement are discussed and typical results presented. Data is presented showing the effects muffler position, exhaust pipe length, tailpipe length, source-receiver phenomena, and exhaust leaks have on radiated exhaust noise.

Partial enclosures are a very common way to reduce noise emissions from machinery. However, partial enclosures exhibit complex acoustic behavior that is difficult to predict. The boundary element method (BEM) was used to model the airborne path of a partial enclosure. Simulation results were compared to measurement with good agreement. Special attention is given to the determination of negative insertion loss. It is demonstrated that the enclosure insertion loss will be negative at the Helmholtz frequencies for the enclosure.

Micro-perforated panels have tiny pores which attenuate sound based on the Helmholtz resonance principle. That being the case, an appropriate cavity depth should be chosen to fully capitalize on the attenuation potential of the panel. Generally, the panel's sound absorbing performance can be predicted by Maa's theory given information about the panel and the cavity depth. However, in some cases, one cannot use the theory to predict the panel's performance precisely, especially when the micro-perforate has varying diameters and/or irregular hole shapes. In these cases, the sound-absorbing performance of the micro-perforate is different from that of a uniform pore diameter perforate. This paper presents an alternative method to predict the micro-perforated panel's performance precisely. As a first step, the transfer impedance of the micro-perforate should be measured.

This paper examines the feasibility of using the boundary element method (BEM) and the Rayleigh integral to assess the sound radiation from engine components such as oil pans. Two oil pans, one cast aluminum and the other stamped steel, are used in the study. All numerical results are compared to running engine data obtained for each of these oil pans on a Cummins engine. Measured running-engine surface velocity data are used as input to the BEM calculations. The BEM models of the oil pains are baffled in various ways to determine the feasibility of analyzing the sound radiated from the oil pan in isolation of the engine. Two baffling conditions are considered: an infinite baffle in which the edge of the oil pan are attached to an infinite, flat surface; and a closed baffle in which the edge of the oil pan is sealed with a rigid structure. It is shown that either of these methods gives satisfactory results when compared to experiment.

The two-load method is commonly used to determine the transmission loss of a muffler or silencer. Several practical measurement considerations are examined in this paper. First of all, conical adapters are sometimes used to transition between impedance tubes and the muffler. It is demonstrated that the effect of adding the adapter can be quite significant at low frequencies especially if the adapter is short in length. The effect of changing the length of the adapter was examined via measurement and plane wave theory. Secondly, the effect of selecting the reference microphone was examined experimentally. It was found that measurements are improved by selecting a downstream reference. Finally, the effect of using different frequency response function estimation algorithms (H1, H2 and Hv) was compared sans flow. This had little effect on the measurement.

Particulate control in car ventilation systems using electrically-charged synthetic filter media are becoming more popular. Adsorption units and low-temperature catalytic systems have been used to control odors and some chemical contaminants in top-of-the-line automobiles. This is a review analyzing these systems, the contaminants found in vehicle environments, and filtration theory. A detailed discussion of experimental work concentrates on overall and fractional filter efficiency and increase in pressure drop with dust loading of charged and uncharged filter media at high aerosol velocity. SAE fine and two natural polydisperse dusts with particles smaller than 5 and 10 μm were used for testing. The health and comfort of car occupants depend on several factors, including air quality. Currently, several car manufacturers offer filtration systems for car interior air.

The lube oil filtration system for diesel engines is becoming increasingly important. Oil filtration systems typically consist of full-flow and bypass filters. A well-designed system will reduce engine wear and oil usage and may play a role in controlling engine emissions. Thus, both economic and environmental benefits are realized. Past work has dealt with the benefits of using finer full-flow filters and with the use of bypass filters; however, the critical issue of optimization of the entire system has largely been ignored. This is the subject of this paper. The removal and dust-holding capacity characteristics of a variety of commercially available and prototype filters, including cellulose, synthetic and “centrifugal” filters, were determined in the laboratory. The performance of these filters in various full-flow/bypass combinations were further evaluated in the field on city buses.

Lack of a precise control over paint droplets released from current coating sprayers has motivated this study to develop an atomizer capable of generating a uniform flow of mono-dispersed droplets. In the current study, a numerical investigation based on CFD incorporating volume of fluid (VOF) multiphase model has been developed to capture the interface between air and paint phases for a typical atomizer equipped with piezoelectric actuator. Effects of inlet flow rate and actuator frequency on ejected droplets' characteristics, droplet diameter and their successive spacing are studied in detail. It will be shown that for a determined flow rate of paint, there is an optimum actuator frequency in which droplet size is minimum. Besides, there exists a direct relationship between the inlet paint velocity and obtained optimal actuator frequency.

This paper documents a finite element approach to predict the attenuation of muffler and silencer systems that incorporate diesel particulate filters (DPF). Two finite element models were developed. The first is a micro FEM model, where a subset of channels is modeled and transmission matrices are determined in a manner consistent with prior published work by Allam and Åbom. Flow effects are considered at the inlet and outlet to the DPF as well as viscous effects in the channels themselves. The results are then used in a macro FEM model of the exhaust system where the transmission relationship from the micro-model is used to simulate the DPF. The modeling approach was validated experimentally on an example in which the plane wave cutoff frequency was exceeded in the chambers upstream and downstream to the DPF.

Helmholtz resonators are normally an afterthought in the design of mufflers to target a very specific low frequency, usually the fundamental firing frequency of the engine. Due to space limitations in a complex muffler design, a resonator may have to be built by punching a few small holes on a thin-walled tube to create a neck passage into a small, enclosed volume outside the tube. The short neck passage created by punching a few small holes on a thin-walled tube can pose a great challenge in numerical modeling, especially when the boundary element method (BEM) is used. In this paper, a few different BEM modeling approaches are compared to one another and to the finite element method (FEM). These include the multi-domain BEM implemented in a substructure BEM framework, modeling both sides of the thin-walled tube and the details of each small hole using the Helmholtz integral equation and the hypersingular integral equation, and modeling just the mid surface of the thin-walled tube.