Search Results

This paper describes the design strategy adopted for developing a new high performance actuation system referred to as the ElectroHydraulic Actuator (EHA). The design approach can be divided into fives phases that include: pre-conceptual analysis, conceptual design, preliminary design, detailed design and, integration and test. An important aspect of the design process is the use of modeling and simulation for the analysis, sizing and selection of off-the-shelf parts, and for the detailed design of new custom made components. EHA is based on hydrostatic transmission. It is a unique device with its own characteristics and requires hydraulic components that are specifically tailored to its needs. A prototype of EHA has been produced and has demonstrated an extremely high level of performance. The performance of this prototype complies with design requirements and validates the chosen design approach.

Nowadays, moving toward more lightweight designs is the key goal of all major automotive industries, and they are always looking for more mass saving replacements. In this study, a new methodology for the design and optimization of cross-car beam (CCB) assemblies is proposed to obtain a more lightweight aluminum design as a substitution for the steel counterpart considering targeted performances. For this purpose, first, topology optimization on a solid aluminum geometry encompassing the entire design space should be carried out to obtain the element density distribution within the model. Reinforcing locations with high element density and eliminating those with density lower than the threshold value result in the conceptual design of the CCB. To attain the final conceptual design, the process of topology optimization and removal of unnecessary elements should be addressed in several steps.

This paper presents the first application of the global feedback linearization method to an internal combustion (IC) engine. Through the application of this nonlinear control technique, the nonlinear coupled dynamics of the IC engine are globally linearized and decoupled. This represents a significant advance over previously published control approaches which rely on locally linearized dynamic models. With the IC engine dynamics globally linearized and decoupled, outer-loop controllers can be readily designed using simple linear tracking controller design methods, leading to very good dynamic response of three key IC engine outputs, air/fuel ratio, engine speed and manifold air pressure. In this paper, a standard IC engine model from the literature is first transformed to a controllable canonical form, required for the application of the global feedback linearization methods.

Recent advances in the development of a more robust synchronization strategy has made it viable to propose a control system for a no-break power transfer in aerospace applications. The proposed system constitutes a combination of a multirate phase locked loop with a positive sequence detector. Synchronization to the positive sequence component, in the presence of unbalanced loads, minimizes the circulating real and reactive power. The amplitude, frequency, and phase of the airplane power source are made available. The no-break control system automatically sets the ground power unit to the frequency and phase of the aircraft power unit and adjusts its amplitude to the required level. The relays are then closed and the ground power unit is connected to the airplane load. The amplitude information is provided by an automatic gain control (AGC) loop.

Many current aftermarket natural gas conversions of gasoline fuelled spark ignited engines use an air-valve type mixer with closed loop control of the gas pressure. This control is often provided by an electronic integral controller that uses the output from an exhaust gas oxygen (EGO) sensor to control the duty cycle of a solenoid valve. By varying the duty cycle of this fuel control valve (FCV), the average pressure in the low pressure regulator (LPR) reference chamber and thus the gas pressure can be varied. The transient behaviour of these fuel systems is affected mainly by the mechanical response of the gas mixer and the LPR. The electronic controller can provide compensation only after the EGO sensor has detected an air-fuel ratio excursion. The main weaknesses of this type of fuel system seems to be associated with the finite response of the mixer and the LPR and by the use of an airflow dependent vacuum signal strength for control.

Methanol, in common with other alternative fuels including natural gas and LPG, has autoignition characteristics which are poorly suited for use in compression ignition engines. Some sort of ignition assist has proven to be necessary. Considerable work has been carried out with hot surface (glow plug) ignition. The geometric relationship between the fuel injection nozzle and the glow plug is critical to achieving high efficiency and low emissions. Moreover, it is difficult to establish a single geometry which provides reliable ignition and stable operation over the entire range of engine speeds and loads. The work described in this paper investigated extending the range of operation of a particular glow plug/fuel injection nozzle geometry by placing the glow plug in the wake of a bluff body. Bluff-body flame stabilization is a well-known technique in continuous combustors. Experiments were carried out in a single-cylinder CFR cetane rating engine fueled with methanol.

TPO is being used to make automotive parts for its number of advantages: i) low temperature flexibility and ductility, ii) excellent impact/stiffness/flow balance, iii) excellent weatherability, and iv) free-flowing pellet form for easy processing, storage, and handling. However, by foaming TPO, due to its higher rigidity-to-weigh ratio, it would offer additional advantages over the solid counterparts in terms of reduced weight, reduced material cost, and decreased fuel usage without compromising their performance. Since a major component in TPO is polypropylene (PP), understanding PP foaming behaviours is an important step towards understanding TPO foaming. For foam materials, cell density and cell size are two significant parameters that affect their material properties. In this research, we observed the cell nucleation and initial growth behaviours of PP foams blown with CO2 under various experimental conditions in a batch foaming simulation system.

A comparison of scanning mobility particle sizer (SMPS) and laser-induced incandescence (LII) measurements of diesel particulate matter (PM) was performed. The results reveal the significance of the aggregate nature of diesel PM on interpretation of size and volume fraction measurements obtained with an SMPS, and the accuracy of primary particle size measurements by LII. Volume fraction calculations based on the mobility diameter measured by the SMPS substantially over-predict the space-filling volume fraction of the PM. Correction algorithms for the SMPS measurements, to account for the fractal nature of the aggregate morphology, result in a substantial reduction in the reported volume. The behavior of the particulate volume fraction, mean and standard deviation of the mobility diameter, and primary particle size are studied as a function of the EGR for a range of steady-state engine speeds and loads for a turbocharged direct-injection diesel engine.

The present paper aims at developing an innovative procedure to create a one-dimensional (1D) real-time capable simulation model for a heavy-duty diesel engine. The novelty of this approach is the use of the top-level engine configuration, test cell measurement data, and manufacturer maps as opposite to common practice of utilizing a detailed 1D engine model. The objective is to facilitate effective model adjustments and hence further increase the application of Hardware-in-the-Loop (HiL) simulations in powertrain development. This work describes the development of Fast Running Model (FRM) in GT-SUITE simulation software. The cylinder and gas-path modeling and calibration are described in detail. The results for engine performance and exhaust emissions produced satisfactory agreement with both steady-state and transient experimental data.

This paper presents an experimental study on the foaming behavior of recyclable high-melt-strength (HMS) branched polypropylene (PP) with CO2 as a blowing agent. The foamability of branched HMS PP has been evaluated using a tandem foaming extruder system. The effects of CO2 and nucleating agent contents on the final foam morphology have been thoroughly investigated. The low density (i.e., 12~14 fold), fine-celled (i.e., 107–109 cells/cm3) PP foams were successfully produced using a small amount of talc (i.e., 0.8 wt%) and 5 wt% CO2.

Some current aftermarket natural gas closed loop carburetion systems use an integral control strategy to maintain a fuel-air equivalence ratio centered in the peak conversion window of a three-way catalytic converter. Fuel control system performance under steady-state engine operating conditions can be characterized by the time-averaged value of the fuel-air equivalence ratio, the rich and lean excursion limits, and a skewness parameter that represents the non-symmetry of the time varying fuel-air equivalence ratio about the control value (ϕaverage). Using a representative aftermarket feedback control system, the effect of these parameters on the exhaust emissions of a natural-gas fueled four-cylinder engine has been investigated. In addition, the effect of EGO sensor characteristics on control system performance has been examined.

A study was performed to determine the effects of engine operating variables and piston and ring parameters on the crevice hydrocarbon emissions from a spark-ignition engine. Natural gas was used as the test fuel in an effort to isolate crevice mechanisms as the only major source of unburned hydrocarbons in the test engine's exhaust. The largest of the in-cylinder crevices, the piston ring pack crevices, were modified, both in size and accessibility, by altering the piston top land height and the number of piston rings and their end gaps. Each piston and ring configuration was subjected to a series of test sweeps of engine operating variables known to affect exhaust hydrocarbon emissions. None of the physical crevice modifications had any significant effect on the level of the exhaust hydrocarbon emissions, although the cycle-to-cycle repeatability of these emissions, measured with a fast hydrocarbon analyzer, was found to vary between the different configurations.

As a result of CAFE (corporate average fuel economy) requirements, the trend in passenger car engine design is to smaller displacement engines of higher specific output which provide reductions in vehicle driving cycle fuel consumption without an accompanying decrease in maximum power output. Design features such as four valves per cylinder and compact combustion chambers give these engines significantly different combustion characteristics than traditional pushrod OHV (overhead valve) engines. In general, their combustion chambers are fast burning, enabling the use of higher compression ratios without knock on unleaded gasoline. Since fuel consumption decreases with increasing compression ratio, and since natural gas has a substantially higher octane rating than the best unleaded gasoline, it would appear to be desirable to operate with even higher compression ratios in a dedicated natural gas engine.

Biodiesel and other renewable fuels are of interest due to their impact on energy supplies as well as their potential for carbon emissions reductions. Waste animal fats from meat processing facilities, which would otherwise be sent to landfill, have been proposed as a feedstock for biodiesel production. Emissions from biodiesel fuels derived from vegetable oils have undergone intense study, but there remains a lack of data describing the emissions implications of using animal fats as a biodiesel feedstock. In this study, emissions of NOx, unburned hydrocarbons and particulate matter from a compression ignition engine were examined. The particulate matter emissions were characterized using gravimetric analysis, elemental carbon analysis and transmission electron microscopy. The emissions from an animal fat derived B20 blend were compared to those from petroleum diesel and a soy derived B20 blend.

Measurements were taken of the speciated aldehyde and ketone exhaust emissions from a modern four-cylinder engine fuelled with natural gas. The effect on these emissions of varying the engine operating parameters spark timing, exhaust gas recirculation rate, engine speed, and fuel/air equivalence ratio was examined. The influence of these operating parameters on the complete reactivity-weighted emissions with natural gas fuelling is predicted. With stoichiometric fuel/air mixtures, both the total hydrocarbons and formaldehyde emissions declined with increasing exhaust gas temperature and increasing in-cylinder residence time, suggesting that formaldehyde burn-up in the exhaust process largely controls its emissions levels. Closer examination of the aldehyde emissions shows they follow trends more like those of the non-fuel, intermediate hydrocarbon species ethane and acetylene, than like the trends of the fuel components methane and ethane.

Throttle tip-in and tip-out tests on a 2.0 litre passenger car engine were performed using four different natural gas fuelling systems an air-valve or variable restriction type mixer, a venturi type mixer, central fuel injection, and port fuel injection. The in-cylinder fuel-air equivalence ratio, ϕ, was measured using a fast response flame ionization detector sampling about 7 mm from the spark plug gap. The data reveal characteristics of each fuel system's in-cylinder fuel-air ratio response and torque response.

The hydrogen-fueled engine has been identified as a viable power unit for ultra-low emission senes-hybrid vehicles The absence of carbon in hydrogen fuel eliminates exhaust emissions of CO, CO2, and hydrocarbons, with the exception of small contributions from the combustion of lubricating oil Thus, the only regulated emission of a hydrogen-fueled engine is NOx, and the engine may be optimized to minimize NOx since the usual constraint of the NOx -hydrocarbon trade-off is not applicable Hydrogen-fueled homogeneous charge piston engines have, however, generally suffered from a variety of combustion difficulties, most notably a proclivity to ignition on hot surfaces such as exhaust valves, spark plug electrodes and deposits on combustion chamber walls The Wankel engine is particularly well suited to the use of hydrogen fuel, since its design minimizes most of the combustion difficulties In order to evaluate the possibilities offered by the hydrogen fueled rotary engine, dynamometer tests were conducted with a small (2 2kW) Wankel engine fueled with hydrogen Preliminary results show an absence of the combustion difficulties present with hydrogen-fueled homogenous charge piston engines The engine was operated unthrottled and power output was controlled by quality governing, i.e. by varying the fuel-air equivalence ratio on the lean side of stoichiometric The ability to operate with quality governing is made possible by the wide flammability limits of hydrogen-air mixtures NOx emissions are on the order of 5 ppm for power outputs up to 70% of the maximum attainable on hydrogen fuel Thus, by operating with very lean mixtures, which effectively derates the engine, very low NOx emissions can be achieved Since the rotary engine has a characteristically high power to weight ratio and a small volume per unit power compared to the piston engine, operating a rotary engine on hydrogen and derating the power output could yield an engine with extremely low emissions which still has weight and volume characteristics comparable to a gasoline-fueled piston engine Finally, since engine weight and volume affect vehicle design, and consequently in-use vehicle power requirements, those factors, as well as engine efficiency, must be taken into account in evaluating overall hybnd vehicle efficiency

Charge dilution is commonly used to reduce emissions of nitrogen oxides (NOx) from internal combustion engine exhaust gas. The question of whether to use air or exhaust gas recirculation (EGR) as a charge diluent for the natural gas-fuelled test engine is addressed first. The decision to use EGR is based on the potentially lower NOx and unburned hydrocarbon emissions that could be achieved if a three-way catalyst were applied to the engine. The effect of EGR on the spark advance for maximum brake torque (MBT), NOx, and unburned hydrocarbon emissions is then examined in detail. The effect on fuel efficiency is discussed briefly.

An experiment was conducted to evaluate the efficiency and emissions of an engine fuelled with a mixture of natural gas and approximately 15% hydrogen by volume. This mixture, called Hythane™, was compared with natural gas fuel using engine efficiency and engine-out emissions at various engine operating conditions as the basis of comparison. Throughout most of the experiment, fuel mixtures were slightly rich of stoichiometry. It was found that at low engine loads, using the same spark timing, engine efficiency increased under HythaneTM fuelling but at higher engine loads, natural gas and Hythane™ had the same efficiency. At low engine speed and load conditions with the same spark timing, engine-out total hydrocarbon (THC) emissions were lower for Hythane™ fuelling. When compared on a carbon specific basis, however, natural gas hydrocarbon emissions were lower. At some test conditions, engine-out carbon monoxide (CO) emissions were lower under Hythane™.

The major disadvantage of powder metallurgy (PM) is the density gradient throughout the green powder compacts. During the compaction process, due to the existence of friction at powder-tool interfaces, the contact surfaces experience a non-uniform stress distribution having to do with variable friction coefficient and tool kinematics, consequently resulting in density gradient throughout the powder compacts. This represents a serious problem in terms of the reliability and performance of a final product, as the density gradient may contribute to a crack-defect generation during the compaction cycle, and more importantly a non-uniform compact shrinkage during the sintering process. Simulation analyses were conducted using the finite element software, MSC.Marc Mentat, and Shima and Oyane powder constitutive model, to study and suppress the causes of density gradient in the cylindrically shaped green powder compacts.