Search Results

An endoscope-based image acquisition-and-processing camera system was used for diagnostics of pilot injection combustion in a single-cylinder heavy duty diesel engine. A study of the pilot injection or light load is of interest because the spray breakup, mixing and vaporization processes are less influenced by heat feedback from the flame than in full injection cases. This allows the spray process to be decoupled from the combustion process. The experimental cases were modeled using a version of the KIVA-II code that includes improvements in the turbulence, wall heat transfer, spray, ignition and combustion models. Pilot injections of three different amounts (10, 15 and 20% of the fuel injected at 75% load and 1600 RPM) at different start-of-injection timings were studied. The imaging system included an endoscope, an intensified CID camera, a frame grabber and the control circuitry.

This paper describes a variable magnetomotive force interior permanent magnet (IPM) machine for use as a traction motor on automobiles in order to reduce total energy consumption during duty cycles and cut costs by using Dy-free magnets. First, the principle of a variable magnetomotive force flux-intensifying IPM (VFI-IPM) machine is explained. A theoretical operating point analysis of the magnets using a simplified model with nonlinear B-H characteristics is presented and the results are confirmed by nonlinear finite element analysis. Four types of magnet layouts were investigated for the magnetic circuit design. It was found that a radial magnetization direction with a single magnet is suitable for the VFI-IPM machine. Magnetization controllability was investigated with respect to the magnet thickness, width and coercive force for the prototype design. The estimated variable motor speed and torque characteristics are presented.

In this paper, large eddy simulation (LES) coupled with two uncertainty quantification (UQ) methods, namely latin-hypercube sampling (LHS) and polynomial chaos expansion (PCE), have been used to quantify the effects of model parameters and spray boundary conditions on diesel and gasoline spray simulations. Evaporating, non-reacting spray data was used to compare penetration, mixture fraction and spray probability contour. Two different sets of four uncertain variables were used for diesel and gasoline sprays, respectively. UQ results showed good agreement between experiments and predictions. UQ statistics indicated that discharge coefficient has stronger impact on gasoline than diesel sprays, and spray cone angle is important for vapor penetration of both types of sprays. Additionally, examination of the gasoline spray characteristics showed that plume-to-plume interaction and nozzle dribble are important phenomena that need to be considered in high-fidelity gasoline spray simulations.

Monochromatic ultraviolet (UV) absorbance, temperature, and pressure histories of unburned gas in a single cylinder CFR engine under motored, fired, and autoignition conditions were recorded on a multichannel magnetic tape recorder. Isooctane, cyclohexane, ethane, n-hexane, n-heptane, 75 octane number (ON), 50 ON, and 25 ON blends of primary reference fuels (PRF) were studied. Under knocking or autoignition conditions a critical absorbance at 2600 A was found, whose magnitude was independent of engine operating variables and dependent only on the knock resistance of the fuel. This absorbance increased rapidly when a certain temperature level was exceeded during the exothermic preflame reactions.

This is a continuation of the presentation of thermodynamic properties of selected fuel-air mixtures in chart form, suitable for utilization in engine performance calculations. Methane and propane, representative of natural gas and LPG are the two fuels considered. Using these charts, comparisons are made between the performance to be expected with these gaseous fuels compared to octane, as representative of gasoline. Reduced engine power is predicted and this is confirmed by experience of other investigators.

This paper presents a theoretical study of different strategies of waste heat recovery in an internal combustion engine, operating in a hybrid vehicle (spark ignition engine and electric motor). Many of the previous studies of energy recovery from waste heat focused on running thermodynamic cycles with the objective of supplying air-conditioning loads. There are two elements of this study that are different from previous studies: first, the end use of the recovered waste heat is the generation of electric power, and, second, the implementation of these heat recovery strategies takes place in a hybrid vehicle. The constant load conditions for the SI-engine in the hybrid vehicle are a potential advantage for the implementation of a heat recovery system. Three configurations of Rankine cycles were considered: a cycle running with the exhaust gases, a cycle with the engine coolant system, and a combined exhaust-engine coolant system.

A detailed description of a numerical method for computing unsteady flows in engine intake and exhaust systems is given. The calculations include the effects of heat transfer and friction. The inclusion of such calculations in a mathematically simulated engine cycle is discussed and results shown for several systems. In particular, the effects of bell-mouth versus plain pipe terminations and the effects of a finite surge tank are calculated. Experimental data on the effect of heat transfer from the back of the intake valve on wave damping are given and show the effect to be negligible. Experimental data on wave damping during the valve closed period and on the temperature rise of the air near the valve are also given.

This paper describes a method for studying reactions of hydrocarbons in S.I. engine exhaust gases. The reaction of ethane is described using an Arrhenius model (experimentally E = 86,500 cal/mole) for the rate of ethane diappearance and empirical correlations for distributions of the products carbon monoxide, ethylene, formaldehyde, methane, acetylene, and propane as a function of the fraction of ethane reacted. The results show that the nature of partial oxidation products from a nonreactive hydrocarbon may be less desirable from an air pollution viewpoint than the initial hydrocarbon.

The ratio of two temperature gradients across the combustion-chamber wall in a diesel engine is used to provide a heat flow ratio showing the radiant heat transfer as a per cent of local total heat transfer. The temperature gradients were obtained with a thermocouple junction on each side of the combustion-chamber wall. The first temperature gradient was obtained by covering the thermocouple at the cylinder gas-wall interface with a thin sapphire window, while the second was obtained without the window. Results show that the time-average radiant heat transfer is of significant magnitude in a diesel engine, and is probably even more significant in heat transfer during combustion and expansion.

Simultaneous two-component measurements of gas velocity and multi-dimensional numerical simulation are employed to characterize the evolution of the in-cylinder turbulent flow structure in a re-entrant bowl-in-piston engine under motored operation. The evolution of the mean flow field, turbulence energy, turbulent length scales, and the various terms contributing to the production of the turbulence energy are correlated and compared, with the objectives of clarifying the physical mechanisms and flow structures that dominate the turbulence production and of identifying the source of discrepancies between the measured and simulated turbulence fields. Additionally, the applicability of the linear turbulent stress modeling hypothesis employed in the k-ε model is assessed using the experimental mean flow gradients, turbulence energy, and length scales.

Engine experiments were conducted on a heavy-duty single-cylinder engine to explore the effects of charge preparation, fuel stratification, and premixed fuel chemistry on the performance and emissions of Reactivity Controlled Compression Ignition (RCCI) combustion. The experiments were conducted at a fixed total fuel energy and engine speed, and charge preparation was varied by adjusting the global equivalence ratio between 0.28 and 0.35 at intake temperatures of 40°C and 60°C. With a premixed injection of isooctane (PRF100), and a single direct-injection of n-heptane (PRF0), fuel stratification was varied with start of injection (SOI) timing. Combustion phasing advanced as SOI was retarded between -140° and -35°, then retarded as injection timing was further retarded, indicating a potential shift in combustion regime. Peak gross efficiency was achieved between -60° and -45° SOI, and NOx emissions increased as SOI was retarded beyond -40°, peaking around -25° SOI.

This study looks at the application of a titanium dioxide (TiO2) catalytic nanoparticle suspension to the surface of the combustion chamber as a coating, as well as the addition of hydrogen gas to a four-stroke spark-ignited carbureted engine as a possible technique for lowering engine-out emissions. The experiments were conducted on two identical Generac gasoline powered generators using two, four and six halogen work lamps to load the engine. One generator was used as a control and the second had key components of the combustion chamber coated with the catalytic suspension. In addition to the coating, both engines were fed a hydrogen and oxygen gas mixture and tested at low, medium and high loads. Using an unmodified engine as a control set, the following three conditions were tested and compared: addition of hydrogen only, addition of coating only, and addition of hydrogen to the coated engine.

In this paper, effect of intake air temperature, coolant temperature, and compression ratio on start of heat release (SOHR) in HCCI engines is investigated. The operational range with HCCI operation was determined experimentally using a CFR (Cooperative Fuels Research) engine with n-butane as the fuel. In-cylinder pressure was processed to evaluate SOHR. The effect of intake air and coolant temperature on SOHR increases as engine speed increases. In order to gain more insight into the combustion phenomena, SOHR was calculated using the theory of Livengood-Wu and compared with the experimental data. Dependence of SOHR on the equivalence ratio shows good correspondence between experiment and calculation. On the contrary, dependence on the intake air temperature and compression ratio shows poorer correspondence with predictions, especially under low engine speed. We interpret this as an indication of the importance of the active intermediate species that remain in the combustion chamber.

The objective of this research was to investigate the effect of injection pressure on air entrainment into transient diesel sprays. The main application of interest was the direct injection diesel engine. Particle Image Velocimetry was used to make measurements of the air entrainment velocities into a spray plume as a function of time and space. A hydraulically actuated, electronically controlled unit injector (HEUI) system was used to supply the fuel into a pressurized spray chamber. The gas chamber density was maintained at 27 kg/m3. The injection pressures that were studied in this current research project were 117.6 MPa and 132.3 MPa. For different injection pressures, during the initial two-thirds of the spray plume there was little difference in the velocities normal to the spray surface. For the last third of the spray plume, the normal velocities were 125% higher for the high injection pressure case.

A correlation was developed to predict the ignition delay of PRF blends at a wide range of engine-relevant operating conditions. Constant volume simulations were performed using Cantera coupled with a reduced reaction mechanism at a range of initial temperatures from 570-1860K, initial pressures from 10-100atm, oxygen mole percent from 12.6% to 21%, equivalence ratios from 0.30-1.5, and PRF blends from PRF0 to PRF100. In total, 6,480 independent ignition delay simulations were performed. The correlation utilizes the traditional Arrhenius formulation; with equivalence ratio (φ), pressure (p), and oxygen mole percentage (xo2) dependencies. The exponents α, β, and γ were fitted to a third order polynomial with respect to temperature with an exponential roll-off to a constant value at low temperatures to capture the behavior expressed by the reaction mechanism. The location and rate of the roll-off functions were modified by linear functions of PRF.

DATA presented in this paper show temperature-time diagrams obtained from mufflers mounted on trucks which were traveling over their regular routes. Using these temperature data, specimens made of possible muffler materials were subjected to laboratory tests. A wide range of possible muffler materials and gas composition were covered in these tests. Results of the tests indicate that under long-run heavy-duty truck service, muffler failure occurs primarily because of high metal temperatures and that coated mild steel showed the most promise of longer muffler life.

Diesel fuels are complex mixtures of thousands of hydrocarbons. Since modeling their combustion characteristics with the inclusion of all hydrocarbon species is not feasible, a hybrid surrogate model approach is used in the present work to represent the physical and chemical properties of three different diesel fuels by using up to 13 and 4 separate hydrocarbon species, respectively. The surrogates are arrived at by matching their distillation profiles and important properties with the real fuel, while the chemistry surrogates are arrived at by using a Group Chemistry Representation (GCR) method wherein the hydrocarbon species in the physical property surrogates are grouped based on their chemical classes, and the chemistry of each class is represented by using up to two hydrocarbon species.

The objectives of this study were 1) to evaluate the characteristics of rich diesel combustion near the stoichiometric operating condition, 2) to explore the possibility of stoichiometric operation of a diesel engine in order to allow use of a three-way exhaust after-treatment catalyst, and 3) to achieve practical operation ranges with acceptable fuel economy impacts. Boost pressure, EGR rate, intake air temperature, fuel mass injected, and injection timing variations were investigated to evaluate diesel stoichiometric combustion characteristics in a single-cylinder high-speed direct injection (HSDI) diesel engine. Stoichiometric operation in the Premixed Charge Compression Ignition (PCCI) combustion regime and standard diesel combustion were examined to investigate the characteristics of rich combustion. The results indicate that diesel stoichiometric operation can be achieved with minor fuel economy and soot impact.

The effect of spray targeting on exhaust emissions, especially soot and carbon monoxide (CO) formation, were investigated in a single-cylinder, high-speed, direct-injection (HSDI) diesel engine. The spray targeting was examined by sweeping the start-of-injection (SOI) timing with several nozzles which had different spray angles ranging from 50° to 154°. The tests were organized to monitor the emissions in Premixed Charge Compression Ignition (PCCI) combustion by introducing high levels of EGR (55%) with a relatively low compression ratio (16.0) and an open-crater type piston bowl. The study showed that there were optimum targeting spots on the piston bowl with respect to soot and CO formation, while nitric oxide (NOx) formation was not affected by the targeting. The soot and CO production were minimized when the spray was targeted at the edge of the piston bowl near the squish zone, regardless of the spray angle.

The purpose of the tests conducted on a single-cylinder laboratory engine was to determine the mechanism of combustion that affect exhaust emissions and the relationship of those mechanisms to engine design and operating variables. For the engine used in this study, the exhaust emissions were found to have the following dependence on various engine variables. Hydrocarbon emission was reduced by lean operation, increased manifold pressure, retarded spark, increased exhaust temperature, increased coolant temperature, increased exhaust back pressure, and decreased compression ratio. Carbon monoxide emission was affected by air-fuel ratio and premixing the charge. Oxides of nitrogen (NO + NO2 is called NOx) emission is primarily a function of the O2 available and the peak temperature attained during the cycle. Decreased manifold pressure and retarded spark decrease NOx emission. Hydrocarbons were found to react to some extent in the exhaust port and exhaust system.