Search Results

Previous research on both small-scale and full-scale vehicles shows that base extensions are an effective method to increase the base pressure, enhancing pressure recovery and reducing the wake size. These extensions decrease drag at zero yaw, but show an even larger improvement at small yaw angles. In this paper, rear extensions are investigated on an SUV in the Volvo Cars Aerodynamic Wind Tunnel with focus on the wake flow and on the unsteady behavior of the surface pressures near the base perimeter. To increase the effect of the extensions on the wake flow, the investigated configurations have a closed upper- and lower grille (closed-cooling) and the underbody has been smoothed with additional panels. This paper aims to analyze differences in flow characteristics on the wake of an SUV at 0° and 2.5° yaw, caused by different sets of extensions attached to the base perimeter. Extensions with several lengths are investigated with and without a kick.

The need for a more complete understanding of the flow behavior in aerodynamic wind tunnels has increased as they have become vital tools not only for vehicle development, but also for vehicle certification. One important aspect of the behavior is the empty test section flow, which in a conventional tunnel should be as uniform as possible. In order to assess the uniformity and ensure consistent behavior over time, accurate measurements need to be performed regularly. Furthermore, the uncertainties and errors of the measurements need to be minimized in order to resolve small non-uniformities. In this work, the quantification of the measurement uncertainties from the full measurement chain of the new flow uniformity measurement rig for the Volvo Cars aerodynamic wind tunnel is presented. The simulation based method used to account for flow interference of the probe mount is also discussed.

During 1991 Volvo Car Corporation has introduced the new Volvo 850 GLT model featuring front wheel drive with transverse installation of the engine and gearbox. The powertrain; consists of a new in-line five-cylinder engine in combination with a four speed electronically controlled automatic gearbox or a five speed manual gearbox. The engine features DOHC 20 valves, V-VIS (Volvo Variable Induction System), well tuned exhaust system and microprocessor controlled engine management systems. The engine was designed and developed as a new member of Volvo's modular engine family. The first member was the in-line six-cylinder engine B6304F [1] introduced in 1990. The modular engines have a large number of identical components and the major components are machined in common transfer lines which makes the manufacturing process highly rational and cost-effective.

Approximately 25 % of a passenger vehicle’s aerodynamic drag comes directly or indirectly from its wheels, indicating that the rim geometry is highly relevant for increasing the vehicle’s overall energy efficiency. An extensive experimental study is presented where a parametric model of the rim design was developed, and statistical methods were employed to isolate the aerodynamic effects of certain geometric rim parameters. In addition to wind tunnel force measurements, this study employed the flowfield measurement techniques of wake surveys, wheelhouse pressure measurements, and base pressure measurements to investigate and explain the most important parameters’ effects on the flowfield. In addition, a numerical model of the vehicle with various rim geometries was developed and used to further elucidate the effects of certain geometric parameters on the flow field.

Direct gasoline injection combined with turbo charging and down sizing is a cost effective concept to meet future requirements for emission reduction as well as increased efficiency for passenger cars. It is well known that turbulence induced by in-cylinder air motion can influence efficiency. In this study, the intake-generated flow field was varied for a direct injected turbo charged concept, with the intent to evaluate if further increase in tumble potentially could lead to higher efficiency compared to the baseline. A single cylinder head with flow separating walls in the intake ports and different restriction plates was used to allow different levels of tumble to be experimentally evaluated in a single cylinder engine. The different levels of tumble were quantified by flow rig experiments.

This paper presents how hardware in the loop (HIL) simulations have been used for testing during the development of the adaptive cruise control (ACC) and collision warning with brake support (CWBS) functions implemented in the Volvo S80. Both the brake system controller and the controller where the ACC and CWBS functions were implemented were tested. The HIL simulator was used for automated batch simulations in which different controller software releases were analyzed from both system, fail-safe and functional performance perspectives. This paper presents the challenges and the benefits of using HIL simulations when developing distributed active safety functions. Some specific simulation results are analyzed and discussed. The conclusion shows that although it is difficult and time-consuming to develop a complete HIL simulation environment for active safety functions such as ACC and CWBS, the benefits justify the investment.

Bushing elasticity is one of the most important compliance factors that significantly influence driving behavior. The deformations of the bushings change the wheel orientations under external forces. Another important factor of bushing compliance is to provide a comfortable driving experience by isolating the vibrations from road irregularities. However, the driving comfort and driving dynamics are often in conflict and need to be balanced in terms of bushing compliance design. Specifically, lateral force steer and brake force steer are closely related to safety and stability and comprises must be minimized. The sensitivity analysis helps engineers to understand the critical bushing for certain compliance attributes, but optimal balancing is complicated to understand. The combination of individual bushing stiffness must be carefully set to achieve an acceptable level of all the attributes.

In modern vehicles, each system must meet tough demands to fulfill the many different attribute requirements, design constraints and manufacturing limitations. It becomes difficult and time-consuming to find an optimal and robust design using a traditional engineering process. Volvo Cars has for several years been using Multi-Disciplinary Optimization, MDO, that basically shows the customer attributes levels, such as NVH, ride comfort, and driveability as a function of different parameter configurations. This greatly facilitates project team understanding of the limitations and possibilities of the different systems, and has become a key enabler to achieving a good balance between different attributes. Traditionally, this type of comprehensive Design of Experiments (DOE) optimization demands huge time and computer resources. Frequently, experimental designs will not fulfill manufacturing limitations or attribute targets, making this decision process slow, tedious, and fruitless.

Flow visualization techniques are widely used in aerodynamics to investigate the surface trace pattern. In this experimental investigation, the surface flow pattern over the rear end of a full-scale passenger car is studied using tufts. The movement of the tufts is recorded with a DSLR still camera, which continuously takes pictures. A novel and efficient tuft image processing algorithm has been developed to extract the tuft orientations in each image. This allows the extraction of the mean tuft angle and other such statistics. From the extracted tuft angles, streamline plots are created to identify points of interest, such as saddle points as well as separation and reattachment lines. Furthermore, the information about the tuft orientation in each time step allows studying steady and unsteady flow phenomena. Hence, the tuft image processing algorithm provides more detailed information about the surface flow than the traditional tuft method.

Automotive electronic systems are becoming safety related causing a need for more systematic and stringent approaches for demonstrating the functional safety. The safety case consists of an argumentation, supported by evidence, of why the system is safe to operate in a given context. It is dependent on referencing and aggregating information which is part of the EAST-ADL2, an architecture description language for automotive embedded systems. This paper explores the possibilities of integrating the safety case metamodel with the EAST-ADL2, enabling safety case development in close connection to the system model. This is done by including a safety case object in EAST-ADL2, and defining the external and internal relations.

An experimental study of EGR and turbocharging concepts has been performed on an experimental 2.0-litre 4-cylinder turbocharged Euro6 light-duty diesel engine. The purpose of the study was to investigate the emissions and fuel consumption trade-off for different concept combinations. The impact of low-pressure and high-pressure EGR was studied in terms of engine-out emissions and fuel consumption. Moreover, the influence of single-stage and two-stage turbocharging was investigated in combination with the EGR systems, and how the engine efficiency could be further improved after engine calibration optimization. During low load engine operation where throttling may be required to achieve the desired low-pressure EGR rate, the difference in fuel consumption impact was studied for exhaust throttling and intake throttling, respectively. The cooling impact on high-pressure EGR was compared in terms of emissions and fuel consumption.

Since several decades, passenger cars and light duty vehicles (LDV) with spark-ignited engines reach full pollutant conversion during warm up conditions; the major challenge has been represented by the cold start and warming up strategies. The focus on technology developments of exhaust after treatment systems have been done in the thermal management in order to reach the warm up conditions as soon as possible. A new challenge is now represented by the Real Driving Emission (RDE) Regulation as this bring more various, and not any longer cycle defined, cold start conditions. On the other hand, once the full conversion has been reached, it would be beneficial for many Exhaust After Treatment System (EATS) components, e.g. for overall durability if the exhaust gas temperature could be lowered. To take significant further emission steps, approaching e.g. zero emission concepts, we investigate the use of Electrical Heating Catalyst (EHC) also including pre-heating.

We describe experiments and numerical modeling of snow surface contamination on two simplified automotive bluff bodies: The Ahmed body and a wedge. The purpose was twofold: 1) To obtain well defined experimental results of snow contamination on simple geometries; 2) To propose a numerical modeling approach for snow contamination. The experiments were performed in a climatic wind tunnel using a snow cannon at −15 °C and the results show that the snow accumulation depends on the aerodynamics of the studied bluff bodies. Snow accumulates on surfaces in proximity to the aerodynamic wakes of the bodies and characteristic snow patterns are obtained on side surfaces. The numerical modeling approach consisted of an aerodynamic setup coupled with Lagrangian particle tracking. Particles were determined to adhere or rebound depending on an adhesion model combined with a resuspension criterion.

In HYGE sled simulations of 35 mph barrier crashes with the Volvo 760 dummy kinematics and injury criteria have been different from what can be observed in barrier crashes One of the major differences between sled testing and barrier crashes is the car pitch in the barrier crashes. In order to improve the sled testing a method to simulate pitch on the sled was developed. Dummy kinematics and injury criteria from sled tests with pitch simulation have proved to be in good agreement with results from barrier crashes. The paper will give a more detailed description of vehicle pitch, the sled pitch arrangement and a comparison of dummy kinematics and injury criteria from barrier crashes and sled testing with and without pitch displacement.

In recent years fuel consumption of passenger vehicles has received increasing attention by customers, the automotive industry, regulatory agencies and academia. However, some areas which affect the fuel consumption have received relatively small interest. One of these areas is the total energy used for vehicle interior climate which can have a large effect on real-world fuel consumption. Although there are several methods described in the literature for analyzing fuel consumption for parts of the climate control system, especially the Air-Condition (AC) system, the total fuel consumption including the vehicle interior climate has often been ignored, both in complete vehicle testing and simulation. The purpose of this research was to develop a model that predicts the total energy use for the vehicle interior climate. To predict the total energy use the model included sub models of the passenger compartment, the air-handling unit, the AC, the engine cooling system and the engine.

To improve fuel efficiency and facilitate handling of the vehicle in a dense city environment, it should be as small as possible given its intended application. This downsizing trend impacts the size of the engine bay, where the air filter box has to be packed in a reduced space, still without increased pressure drop, reduced load capacity nor lower filtering efficiency. Due to its flexibility and reduced cost, CFD simulations play an important role in the optimization process of the filter design. Even though the air-flow through the filter box changes as the dust load increases, the current modeling framework seldom account for such time dependence. Volvo Car Corporation presents an industrial affordable model to solve the time-dependent dust load on filter elements and calculate the corresponding flow behavior over the life time of the air filter box.

In recent years fuel consumption of passenger vehicles has received increasing attention by customers, the automotive industry, regulatory agencies and academia. However, some areas which affect the fuel consumption have received relatively small interest. One of these areas is the total energy used for vehicle interior climate which can have a large effect on real-world fuel consumption. Realistic combinations of energy saving measures were evaluated regarding the total energy use for vehicle interior climate using a one dimensional (1D) simulation model. The 1D simulation model included sub models of the passenger compartment, the air-handling unit, the Air Conditioning (AC) system, engine and engine cooling system. A test cycle representative for real-world conditions was developed. The test cycle included tests in cold, intermediate and warm conditions and the results were weighted with the estimated use in each condition.

This paper describes results from fault injection experiments using heavy ions in the time-triggered communication protocol for safety critical distributed systems (TTP/C, C1 implementation). The observed results show that arbitrary faults in one erroneous node could cause inconsistencies in the cluster and thus jeopardize correctly working nodes and the whole communication system. The described inconsistencies resulted from either asymmetric value faults or slightly out of specification timing faults. This system behavior can be partly explained by too strict constraints on the fault handling algorithms using the membership agreement protocol.

Several of the exterior noise sources existing around a vehicle can cause airborne noise issues at relatively low frequencies. SEA, traditionally used for airborne sound issues is not suitable for the frequency range of interest. Finite Element analysis has been used. Handling of the non-reflecting condition on the outer boundary of the exterior cavity is an issue. Recently, advances have been made in several commercially available codes, which made the analysis practical. Including the poro-elastic material model for foam-based carpets is also becoming practically possible. The purpose of the current study is to investigate the practical applications of those new developments against test data, and to estimate the feasibility of using these procedures in the vehicle development projects. Measurements were carried out in a new semi-anechoic chamber at Volvo Cars. These measurements involved 3 body objects - a Body-in-Blue (BIB) sedan, a Complete Vehicle (CV) sedan and a CV wagon.

In areas such as Active Safety, new technologies, designs (e.g. AUTOSAR) and methods are introduced at a rapid pace. To address the new demands, and also requirements on Functional Safety imposed by ISO 26262, the support for engineering methods, including tools and data management, needs to evolve as well. Generic and file-based data management tools, like spreadsheet tools, are popular in the industry due to their flexibility and legacy in the industry but provide poor control and traceability, while rigid and special-purpose tools provide structure and control of data but with limited evolvability. As organizations become agile, the need for flexible data management increases. Since products become more complex and developed in larger and distributed teams, the need for more unified, controlled, and consistent data increases.