Search Results

The need for a more complete understanding of the flow behavior in aerodynamic wind tunnels has increased as they have become vital tools not only for vehicle development, but also for vehicle certification. One important aspect of the behavior is the empty test section flow, which in a conventional tunnel should be as uniform as possible. In order to assess the uniformity and ensure consistent behavior over time, accurate measurements need to be performed regularly. Furthermore, the uncertainties and errors of the measurements need to be minimized in order to resolve small non-uniformities. In this work, the quantification of the measurement uncertainties from the full measurement chain of the new flow uniformity measurement rig for the Volvo Cars aerodynamic wind tunnel is presented. The simulation based method used to account for flow interference of the probe mount is also discussed.

Experience from several car projects shows that S-N curves for spot welds generated under load control in the high cycle fatigue regime might be very conservative when used in the low cycle fatigue regime. Therefore, force and displacement controlled low cycle fatigue tests were carried out on peel and shear loaded specimens. Both constant (CA) and variable amplitude (VA) load signals were used. Finally, a method for predicting fatigue life of spot welds with increased accuracy in the low cycle fatigue regime is proposed. The method is simple, fast and accurate and can be used together with linear finite element analysis (FEA) and existing fatigue packages.

Model based development promises to facilitate the development of embedded control systems, including design, early verification and validation as well as implementation. Existing tools are beginning to support the development of distributed control systems. There are however still challenges when it comes to integration with mechanics and methodologies for such interdisciplinary systems.

Vehicle dynamics development relies on subjective assessments (SA), which is a resource-intensive procedure requiring both expert drivers and vehicles. Furthermore, development projects becoming shorter and more complex, and increasing demands on quality require higher efficiency. Most research in this area has focused on moving from physical to virtual testing. However, SA remains the central method. Less attention has been given to provide better tools for the SA process itself. One promising approach is to introduce computer-tablets to aid data collection, which has proven to be useful in medical studies. Simple software solutions can eliminate the need to transcribe data and generate more flexible and better maintainable questionnaires. Tablets’ technical features envision promising enhancements of SA, which also enable better correlations to objective metrics, a requirement to improve CAE evaluations.

The following paper describes how to measure the global torsional stiffness of a complete car under field-like conditions. All that's needed are lifting devices, two stands of equal height, three glide planes or equivalent, three scales and two inclinometers, a spirit level, some pieces of aluminum and a glue gun. The results from four measured cars are presented and a comparison is made with values obtained with laboratory equipment and data from manufacturers. The method is a fast and economic means to find the most interesting cars that then can be selected for measurement by traditional methods, giving the stiffness as a function of the vehicles long axis, and thus minimizes the cost of benchmarking. Time for measuring one car with all equipment readily available and with personnel having some experience of the method is about two hours. Only the sway bars have to be disconnected. Absolutely no damage to the measured car means that rented cars can be used.

A finite-element (FE) based method for numerically predicting fatigue life of MAG-welded thin-sheet structures has been established and tested. The method uses nodal forces and moments calculated along the weld line, together with an analytical expression for the structural stress at the weld toe. The calculated stress is used together with an experimentally determined Wöhler, or S-N, curve. A “stiff” welded joint with structural stress dominated by membrane forces is found to have a steeper S-N curve than a “flexible” joint with structural stress dominated by bending moment. All test results were seen to lie close to one of two different S-N curves. The proportion of bending stress over total structural stress could be used for choosing the appropriate S-N curve.

The objective of this investigation was to improve the thermal properties of plasma sprayed thermal barrier coatings (TBC) for internal combustion engines. There is a need for further reduction of thermal conductivity and volumetric heat capacity and the negative effects on heat loss and combustion phasing of surface roughness and permeable porosity, typical for plasma sprayed coatings, should be minimized. Four measures for improvement of TBC properties were evaluated: i) modification of the coating's microstructure by using a novel suspension plasma spraying method, ii) application of gadolinium-zirconate, a novel ceramic material with low thermal conductivity, iii) polishing of the coating to achieve low surface roughness, and iv) sealing of the porous coating surface with a polysilazane. Six coating variants with different combinations of the selected measures were applied on the piston crown and evaluated in a single cylinder light duty diesel engine.

The automotive industry strives to develop high quality vehicles in a short period of time that satisfy the consumer needs and stand out in the competition. Full exploitation of simulation and Computer-Aided Engineering (CAE) tools can enable quick evaluation of different vehicle concepts and setups without the need of building physical prototypes. Addressing the aforementioned statements this paper presents a method for optimising the Electric Power-Assisted Steering (EPAS) ECU parameters employing solely CAE. The objective of the optimisation is to achieve a desired steering response. The developed process is tested on three specific steering metrics (friction feel, torque build-up and torque deadband) for two function parameters (basic steering torque and active return) of the EPAS. The optimisation method enabled all metrics to fall successfully within the target range.

The objective of this paper is to investigate whether different appearance modes of the digital human models (DHM or manikins) affect the observers when judging a working posture. A case where the manikin is manually assembling a battery in the boot with help of a lifting device is used in the experiment. 16 different pictures were created and presented for the subjects. All pictures have the same background, but include a unique posture and manikin appearance combination. Four postures and four manikin appearances were used. The subjects were asked to rank the pictures after ergonomic assessment based on posture of the manikin. Subjects taking part in the study were either manufacturing engineering managers, simulation engineers or ergonomists. Results show that the different appearance modes affect the ergonomic judgment. A more realistic looking manikin is rated higher than the very same posture visualized with a less natural appearance.

When designing components, systems and fluid characteristics, thermal loads gathered over the life cycle of an automobile are of great interest. Ageing and deterioration based on the temperature/time distribution that a component or fluid is exposed to, affects the functionality and/or durability of electronics, polymers and lubricants. Optimal design in terms of quality and cost are two of the most governing parameters at Volvo Cars at present. To meet this need, designing terms of life cycles from a thermal perspective has been developed during recent years. This paper presents a methodology for designing components and choosing system solutions from life span thermal loads in Volvo Car's vehicles. The fundamental ideas behind the method, design criteria and examples of usage are discussed from a holistic point of view.

Structural topology optimization is a truly interesting and important area, which has developed very rapidly and matured considerably in many fields. However, the use of topology optimization for global structures, using detailed design, is still tremendously time-consuming. From this perspective, the author sees the development of methods and tools to include optimization on simplified models during the design process as the most interesting and important step towards implementing structure topology optimization in the vehicle industry. In the design process, structures are broken down into beams and joints, and are described using a PBM (Property Based Model). Beams are described using a rectangular cross-section with the possibility of being changed in size, shape and orientation. Joints are described as flexible elements using a set of sub-elements called 2-joints that makes it possible for the joint model to change topology and stiffness.

In the early days of the automotive industry, durability and reliability were hit or miss affairs, with end-users often being the first to know about any durability problems - and in many cases forming an essential part of the development process. More recently, automotive companies have developed proving ground and laboratory test procedures that aim to simulate typical or severe customer usage. These test procedures have been used to develop the products through a series of prototypes and to prove the durability of the product prior to release in the marketplace. Now, commercial pressures and legal requirements have led to increasing reliance on CAE methods, with fatigue life prediction having a central role in the durability engineering process.