Search Results

Correct simulations of rotating wheels are essential for accurate aerodynamic investigations of passenger vehicles. Therefore, modern automotive wind tunnels are equipped with five-belt moving ground systems with wheel drive units (WDUs) connected to the underfloor balance. The pressure distribution on the exposed areas of the WDU belts results in undesired lift forces being measured which must be considered to obtain accurate lift values for the vehicle. This work investigates the parasitic WDU lift for various configurations of a crossover SUV using numerical simulations that have been correlated to wind tunnel data. Several parameters were considered in the investigation, such as WDU size, WDU placement, tyre variants and vehicle configurations. The results show that the parasitic lift is more sensitive to the width than the length of the WDU. However, the belt length is also important to consider, especially if the wheel cannot be placed centred.

A primary goal within the industry is to shorten the lead time to get shorter time to market and lower cost. System verification can set the limits for how short the lead time can be. Traditionally verification of automotive communication systems like Remote Keyless Entry, RKE, is performed in a complete vehicle late in the product development process. To fulfill the quality demands during the shorter project time Volvo Cars, VCC, has experienced that it is necessary to develop new requirements and verification methods. Six Sigma contains a complete toolbox to do this in a structured and time efficient way. VCC has together with other Ford Motor Company, FMC, brands and the supplier Continental developed methods and requirements so that the RKE system can be verified before vehicles are built. Only a last validation has to be performed in a complete vehicle.

Toyota Motor Corporation has developed a new six-speed automatic transmission AB60E for longitudinal front engine rear wheel drive (RWD) vehicles. This transmission development was aimed at an improvement of power performance and fuel economy, while achieving a lightweight, compact package and a high torque capacity. In order to achieve this target, a high-capacity ultra-flat torque converter, a highly-rigid transmission case, and an ATF warmer with a valve to switch ATF circuits to an air-cooled ATF cooler have been newly developed. Moreover, a new transmission mode control logic “TOW / HAUL” has been developed to improve power performance and driveability during trailer towing. This automatic transmission has adopted the same gear train and hydraulic control system as the conventional six-speed automatic transmission A760E. This paper describes the structure, major features and performance of the transmission in detail.

The objective of this study was to investigate which of the artificial aging cycles available in the automotive industry that causes major deactivation of three-way catalysts (TWCs) and can be used to obtain an aged catalyst similar to the road aged converter (160 000km). Standard bench cycle (SBC) aging with secondary air injection (SAI) covered aging with various mass flows - a flow from three cylinders into one catalyst system and a flow from three cylinders into two parallel connected catalysts. For rapid catalyst bench aging, secondary air injection is a very efficient tool to create exotherms. Furthermore, the effect on catalytic activity of SAI aging with poisons from oil and fuel dopants (P, Ca, Zn) was investigated. The catalysts were thoroughly characterized in light-off and oxygen storage capacity measurements, emission conversion as a function of lambda and load variation was determined.

Vehicles have been more required to save energy against the background of the tendency of ecology. As the result of improving efficiency of internal combustion engines and adoption of electric power train, heat loss from engine coolant, which is used to heat the cabin, decreases and consequently additional energy may be consumed to maintain thermal comfort in the passenger compartment in winter. This paper is concerned with the humidity control system that realizes reduction of ventilation heat loss by controlling recirculation rate of the HVAC system by using highly accurate humidity sensor to evaluate risk of fogging on the windshield. As the results of the control, fuel consumption of hybrid vehicles decreases and maximum range of electric vehicles increases.

Vehicle electrification is one of the biggest trends in the automotive industry. Without the presence of combustion engine, which is the main noise source on conventional vehicles, noise from other components becomes more perceivable; among these components, the cooling fan is one of the major noise sources, especially during battery charging. The design of cooling fan modules is usually carried out in the early stage before building prototype vehicles. Therefore, understanding the installation effects of the cooling fan on the radiated sound is essential to secure good customer satisfaction. In this study, three different measurement setups of cooling fans are carried out: free field, wall mounted, and in-vehicle measurement. Four cooling fan prototypes with different fan blade designs are used in each measurement. Correlations of these measurements are investigated through comparisons of the measurement results.

Maximum fuel injection pressures for GDI engines is expected to increase due to positive effects on emissions and engine-efficiency. Current GDI injectors have maximum operating pressures of 35 MPa, but higher injection pressures have yielded promising reductions in particle number (PN) and improved combustion stability. However, the mechanisms responsible for these effects are poorly understood, and there have been few studies on fuel sprays formed at high injection pressures. This paper summarizes experimental studies on the properties of sprays formed at high injection pressures. The results of these experiments can be used as inputs for CFD simulations and studies on combustion behavior, emissions formation, and combustion system design. The experiments were conducted using an injection rate meter and optical methods in a constant volume spray chamber. Injection rate measurements were performed to determine the injectors’ flow characteristics.

A direct injection spark ignition (DISI) gasoline engine with a new stratified charge combustion concept has been launched on the Japanese domestic market. This new concept consists of two components. First, a thin fan-shaped spray from a slit nozzle enables wide spray dispersion, moderate spray penetration and a fine atomization. Second, a shell-shaped piston cavity allows better mixture formation, however avoiding distinct charge motions (such as tumble or swirl). Simple intake port geometry increases the full load performance. The combustion concept, at the same time allows stratified charge to be used at higher load and at higher engine speeds and improves the homogeneous charge combustion. A new 3L in-line 6 gasoline engine with this combustion concept showed 20% better fuel economy than a 3L port fuel injection (PFI) engine (λ=1 feed back system) under the Japanese 10-15 mode.

This paper presents the oil circulation behavior in a CO2 climate control system operating at low evaporating temperature down to -32°C. The increase of oil circulation ratio (OCR) from 0 to 6 wt.% during steady state conditions degrades the coefficient of performance and cooling capacity by 15% and 8%, respectively. The pressure drop across the heat exchangers increases, especially in the gas cooler. In low temperature CO2 systems some fluctuations of oil and refrigerant flow rates were observed during cyclic operations when the system did not equip the oil separator, but was observed only at high oil charge when the system did equip the oil separator. These instabilities lead to a periodic compressor performance fluctuation, which caused system performance degradations. Therefore, the use of an oil separator is recommended for the low temperature operation if an ordinary metering valve is adopted as an expansion device without any special control strategy.

The hole diameter of injection nozzles in diesel engines has become smaller and the nozzle coking could potentially cause injection characteristics and emissions to deteriorate. In this research, engine tests with zinc-added fuels, deposit analyses, laboratory tests and numerical calculations were carried out to clarify the deposit formation mechanisms. In the initial phase of deposit formation, lower zinc carboxylate formed close to the nozzle hole outlet by reactions between zinc in the fuel and lower carboxylic acid in the combustion gas. In the subsequent growth phase, the main component changed to zinc carbonate close to nozzle hole inlet by reactions with CO₂ in the combustion gas. Metal components and combustion gases are essential elements in the composition of these deposits. One way of removing these deposits is to utilize cavitations inside the nozzle holes.

For improving DI diesel engine performance, such as lower nitrogen oxidant (NOx), particulate molecular (PM) emission and higher output, etc., atomization of the fuel spray plays an important role. In order to obtain better fuel atomization without increasing the fuel injection pressure, increasing the flow velocity at the injection nozzle spray holes is regarded as an effective way. Through experiments, enlarging the chamfer at the spray hole inlet proved to be the most effective and suitable method for establishing high flow velocity injection nozzles. We have compared the high flow velocity injection nozzles with conventional nozzles in terms of injection characteristics and fuel spray characteristics, and confirmed the improved fuel spray atomization with the high flow velocity injection nozzles. Finally the high flow velocity injection nozzles were tested on a medium duty class, natural aspirated DI diesel engine.

In an ever-transforming sector such as that of private road transport, major changes in the propulsion systems entail a change in the perception of the noise sources and the annoyance they cause. As compared to the scenario encountered in vehicles equipped with an internal combustion engine (ICE), in electrically propelled vehicles the heating, ventilation, and air conditioning (HVAC) system represents a more prominent source of noise affecting a car’s passenger cabin. By virtue of the quick turnaround, steady state Reynolds-averaged Navier Stokes (RANS)- based noise source models are a handy tool to predict the acoustic power generated by passenger car HVAC blowers. The study shows that the most eminent noise source type is the dipole source associated with fluctuating pressures on solid surfaces.

This paper will focus on fuel flow analysis in nozzles, in particular, in the injection hole, a key component of Fuel Injection Equipment(FIE). Optimum controlled flow in the hole improves flow efficiency and atomization. To meet the emission regulations which will be introduced from the end of '90's to the 21st century, Diesel Engines require FIE to produce higher injection pressure which creates better atomization and higher utilization of air. But higher injection pressure results in increased pump driving torque, larger pump size and higher cost. We have studied the improvement in fuel flow characteristics of the nozzle, using an enlarged flow model and the theoretical analysis method. As a result, we have found that the cavitation, which occurs at the inlet of the hole, is affected by the configuration of the sac hole and injection hole. And, furthermore, the cavitation has a direct effect on the contraction and its recovery flow.

An experimental analysis was executed on a NA (Natural Aspirated) 4-stroke gasoline engine to investigate the potential of exhaust waste energy recovery using power turbine technology for light duty application. Restrictions with decreasing diameter were mounted in the exhaust to simulate different vane positions of a VGT (Variable Geometry Turbine) and in-cylinder pressure measurements were performed to evaluate the effect of increased exhaust back pressure on intake- and exhaust pumping losses and on engine performance. Test points in the engine map were chosen on the basis of high residence time for the vehicle during the NEDC (New European Driving Cycle). The theoretically retrievable power was calculated in case a turbine is mounted instead of a restriction and the net balance was obtained between pumping power losses and recovered energy.

Recently, there is a need for new applications of pressure sensor, such as direct fuel injection systems for protecting the environment, or power assisted brake systems for improved driving safety. For these widening areas of application, pressure sensors with higher accuracy, a wider pressure-sensing range, and integration of sensor chip functions are required. This paper discusses our development of automotive semiconductor pressure sensors.

The use of turbochargers with downsized internal combustion engines improves road vehicles’ energy efficiency but introduces additional sound sources of strong acoustic annoyance on the turbocharger’s compressor side. In the present study, direct noise computations (DNC) are carried out on a passenger vehicle turbocharger compressor. The work focuses on assessing the influence of grid parameters on the acoustic predictions, to further advance the maturity of the acoustic modelling of such machines with complex three-dimensional features. The effect of the boundary layer mesh structure, and of the spatial resolution of the mesh, on the simulated acoustic signatures is investigated on detached eddy simulations (DES). Refinements in the core mesh are applied in areas of major acoustic production, to generate cells with sizes proportional to the local Taylor microscale values.

From the view of suppressing the global warming and environmental pollution, responding to the regulation of fuel consumption and exhaust gases along with lengthening the maintenance interval, are becoming more demanded. The development of a high-performance, long-life spark plug has become essential in response to these demands. While improved performance (high ignitability and low required voltage), the discharge part of the spark plug needs to be reduced in size. But, in the past this has been difficult because of the limitations of platinum alloys in terms of wear. Therefore, it has been quite difficult to achieve both smaller discharge parts and longer life. To dramatically improve wear resistance, we researched materials that are both resistant to oxidation and have a high melting point. This research resulted in our development of a new iridium alloy (Iridium-10wt%Rhodium).

The need to improve fuel consumption by saving the weights of automobile parts is growing from the viewpoint of global warming mitigation. In the case of a throttle body for controlling the air flow volume into an engine, it is important to achieve a high dimensional accuracy of the valve-bore gap in the state of closed valve. In fact, most throttle bodies are made of precision-machined metal. Therefore, resin throttle bodies are drawing attention as a lightweight alternate. However, in comparison with metal throttle bodies, resin throttle bodies have two potential disadvantages that should be solved prior to productization. The first one is greater air leakage in the state of closed valve, and the second one is smaller heat conduction for unfreezing the valve in a frigid climate. We have developed an electronic resin throttle body that has overcome the above-mentioned disadvantages.

The required fuel spray characteristics, controlled fuel pressure, and injector installation configurations in gasoline direct injection differ among manufacturers. As a result, there are currently a variety of injector types and configurations being proposed by many different component manufacturers. This paper proposes a new injector design that both enables high fuel pressure operation by utilizing a highly efficient electromagnetic valve using a composite magnetic material for the injector actuator, and increases manufacturing productivity while also meeting the requirements of each engine manufacturer by simplifying the construction of the injector.

Cogeneration (also combined heat and power, CHP) systems have become widely used in recent years for reasons such as efficient use of energy resources and CO₂ emissions reduction. As a power source in cogeneration, gas engines are widely used. Large gas engines have a different ignition system from those in medium-sized and small ones. To burn the fuel mixture to the cylinder wall, many large gas engines (2MW or more outputs) with wide cylinder-bore have a pre-chamber. Flame jets from the pre-chamber enable rapid combustion of super lean mixtures throughout the cylinder walls, achieving improved heat efficiency. In contrast, many medium-sized to small gas engines (less than 2 MW outputs) have a general and simple open-chamber, in which a flame kernel produced by the electric spark of a spark plug ignites the mixture in the combustion chamber.