Search Results

The fatigue behavior of Hilok fastener joints under constant amplitude loading has been investigated experimentally. The effects of load transfer in an unbalanced joint configuration was characterized in terms of a stress severity factor relative to the open-hole configuration. The experimental data indicates that the clamp-up forces dominate the performance of fastener joints with the open-hole fatigue life being the lower bound at the stress levels investigated. The failure modes were observed to transition from a net-section type failure across the minimum section to a fretting induced failure at some distance from the hole. The experimental data has been used to develop stress severity factors to be used as a measure of the fatigue quality of the fastener joints.

Experimental studies were conducted to investigate the effect of tailplane icing on the aerodynamic characteristics of 15%-scale business jet aircraft. The simulated ice shapes selected for the experimental investigation included 9-min and 22.5-min smooth and rough LEWICE ice shapes and spoiler ice shapes. The height of the spoilers was sized to match the horns of the LEWICE shapes on the suction side of the horizontal tail. Tests were also conducted to investigate aerodynamic performance degradation due to ice roughness which was simulated with sandpaper. Six component force and moment measurements, elevator hinge moments, surface pressures, and boundary layer velocity profiles were obtained for a range of test conditions. Test conditions included AOA sweeps for Reynolds number in the range of 0.7 based on tail mean aerodynamic chord and elevator deflections in the range of -15 to +15 degrees.

An aging aircraft accumulates fatigue cracks commonly referred to as multiple site damage (MSD). A simplified engineering fracture mechanics model, generally referred to as the linkup model (or plastic zone touch model), has been used with some success to describe the MSD fracture phenomenon in 2024-T3 aluminum panels. A disadvantage of the linkup model is that it gives excessively inaccurate results for some configurations. A modified linkup model has been developed through empirical analysis of test data taken from unstiffened panels with MSD cracks at open holes. The modified linkup model was then validated with test data from stiffened panels including single-bay panels with the lead crack centered between stiffeners and two-bay panels with the lead crack centered beneath a severed stiffener. Further validation of the modified linkup model was done with test data from panels with bolted lap joints. Test results were obtained from 112 different panels.

Multiple site damage (MSD) on aging aircraft accumulates from fatigue loading over a period of time. For ductile materials such as 2024-T3 aluminum, MSD may lower the strength below that which is predicted by conventional fracture mechanics. An analytical model referred to as the linkup (or plastic zone touch) model has previously been used to describe this phenomenon. However, the linkup model has been shown to produce inaccurate results for many configurations. This paper describes several modifications of the linkup model developed from empirical analyses. These modified linkup models have been shown to produce accurate results over a wide range of configurations for both unstiffened and stiffened flat 2024-T3 panels with MSD at open holes. These modified models are easy to use and give quick and accurate results over a large range of parameters.

While operational airships globally number in the low dozens, interest in buoyant or semi-buoyant platforms continues to arouse imaginations of commercial and military planners and developers alike. The airship-as-advertisement business model is the only model that has proven sustainable on any scale since the crash of the initially successful LZ-128 Hindenburg effectively ended regular passenger and cargo transport by airship, and the 1962 termination of the US Naval airship program terminated regular large-scale surveillance from airships. Efforts in the US and Japan during the 2000's to have a self-sustaining sight-seeing business model using the modern semi-rigid Zeppelin NT both failed. In theory, the buoyant nature of airships provides compelling endurance and cost-per-ton-mile capability which fills a niche arguably not currently occupied by other modes of transportation.

The residual strength of an aluminum panel with a centric hole and one cracked ligament was investigated experimentally. Each of the 7075-T6 aluminum panels which were tested included a cracked ligament of varying length on one side of the centric hole and an uncracked ligament on the other side of the hole. The failure of such a panel subjected to uniform tensile loading normally occurs according to the lower of two modes: brittle fracture or a net section type of yielding. On the other hand, the question of whether one or both ligaments fail is not easily answered. Results show that one or two ligament failure depends upon test conditions such as crack length and loading method. For short crack lengths, the uncracked ligament will fail almost simultaneously with the failure of the cracked ligament.

The Refill Friction Spot Joining (RFSJ) is an emerging solid-state spot welding technology that thermo-mechanically creates a molecular-level bond between the work-pieces. RFSJ does not consume any filler or foreign materials so that no additional weight is introduced to the assembly. As the solid-to-liquid phase transition is not involved in RFSJ in general, there is no lack of fusion or material deterioration caused by liquefaction and solidification. Unlike the conventional friction stir spot welding, RFSJ produces a spot joint with a perfectly flush surface finish without a key or exit hole. Currently, the aerospace industry employs solid rivets for fastening the primary structures as they meet the baseline requirements and have well-established standards and specifications.

The necessity of avoiding the destructive and non-repeatable FSST (Full Scale Sled Test) makes it desirable to devise a cheaper and more repeatable method which can supplant this test procedure. This need developed the HCTD (HIC Component Testing Device) which is capable of providing conservative HIC results with higher repeatability. The computational model of the HCTD is validated against one of the tests conducted at CAMI with polyethylene foam. This validated model is used to conduct a series of tests with input parameters similar to the sled test to develop the correlation between the sled test and HCTD. This study hence concludes that a validated computational model of HCTD can be successfully utilized to address the HIC compliance issues for a foam padded surface.

An experimental study was performed to investigate large droplet dynamics in the vicinity of an airfoil. The investigation was conducted using the NASA Glenn Droplet Imaging Flow Tunnel (DrIFT). Mono-dispersed large droplets were released at the tunnel inlet and accelerated toward an airfoil that was mounted in the test section. The dynamic behavior of a droplet's encounter with the airfoil, which may involve droplet distortion, break-up, impingement and splashing, was recorded using a high-speed imaging system. The effects of the droplet size, tunnel velocity and airfoil configuration on the droplet dynamics were investigated in a parametric study. The droplet sizes used in the experimental study were 96 and 375 μm whereas tunnel velocities were varied from 80 to 130 mph. Three different airfoil geometries were used in the experimental study; a ‘clean’ and ‘iced’ airfoil, and a ‘clean’ three-element high-lift airfoil. The incidence angle of these airfoils was set to zero degrees.

A methodology for developing spray rigs for icing cloud simulation is presented. This methodology includes Computational Fluid Dynamics (CFD) analysis and icing tunnel experiments and was applied to design a spray rig system for a small airborne icing tanker. An in-house spray system was developed and tested in a laboratory to assess two commercially available nozzles - a single-jet type and a multi-jet type - which were capable of producing both FAR Part 25 Appendix C and SLD icing clouds. Spray rig characteristics evaluated during the laboratory tests included air and water flow rates as well as droplet size and distributions. The effects of airspeed and nozzle spacing on spray plume size and uniformity were investigated in a small icing tunnel facility with a two-nozzle spray rig. The experimental data were compared with three-dimensional numerical simulation results obtained with the FLUENT software.

An algorithm is developed and validated for automatic avoidance of restricted airspaces. This method is devised specifically for implementation with an advanced flight control system designed for general aviation application. The algorithm presented here implements two inputs to the aircraft; the bank angle, and the airspeed, while the control system always ensures coordinated maneuvers. Unlike collision avoidance systems, the current method is not designed to serve in an advisory role, but to assume complete control of the aircraft if necessary. It is demonstrated that in order to implement this technique, the aircraft must be assigned an immediate domain whose size would have to depend on the aircraft performance and flight conditions. The strategy is designed such that as the domain surrounding the aircraft approaches that of the restricted airspace, aircraft control would switch gradually away from the pilot and to the controller, which would initiate an evasive maneuver.

Drilling is one of the most widely applied manufacturing operations. Millions of holes are drilled today in manufacturing industries especially in aerospace industry where high quality holes are essential. Rejection and rework rate of the products because of the bad hole is quite high. In this research graphite/honeycomb composite material and aluminum sheet metal has been used. The results show that drill geometry, speed and feed rate have substantial effects on the hole quality and also there was gradual variation of the thrust and lateral forces with feed rates.

The work presented in this paper is part of a long-term research program to explore methods for improving bleed air system performance. Another objective of this research is to provide detailed experimental data for the development and validation of simulation tools used in the design and analysis of bleed air systems. A business jet wing was equipped with an inner-liner hot air ice protection system and was extensively instrumented for documenting system thermal performance. The wing was tested at the NASA Glenn Icing Research Tunnel (IRT) for representative in-flight icing conditions. Data obtained include bleed air supply and exhaust flow properties, wing leading edge skin temperatures, temperatures and pressures in the interior passages of the bleed air system, flow properties inside the piccolo tube, photos of run back ice shapes and ice shape traces. Selected experimental results for a warm hold icing condition are presented in this paper.

An experimental study was conducted to investigate ice-adhesion on clean and coated aluminum surfaces. A test apparatus using the parallel plate linear shear technique was designed along with a data acquisition system for conducting the tests and recording the experimental data. A low pulling rate was applied to specially prepared test specimens for measuring the strength of ice adhesion for a range of test conditions. The effects of surface roughness, surface contamination, and water impurity on ice adhesion were investigated. In addition, tests were conducted to evaluate the effectiveness of a low ice-adhesion coating applied to aluminum test specimens. The results obtained showed that the bond between ice and metal was considerably lower for tap water than for distilled water. For the clean and coated aluminum surfaces the strength of ice adhesion varied with specimen roughness. However, no clear trend was established between ice adhesion strength and surface roughness.

Most composite assemblies and structures generally fail due to weak interlaminar properties and poor performance of their bonded joints that are assembled together with an adhesive layer. Adhesive failure and cohesive failure are among the most commonly observed failure modes in composite bonded joint assemblies. These failure modes occur due to the lack of reinforcement within the adhesive layer in transverse direction. In addition, the laminated composites fail due to the same reason that is the lack of reinforcement through the thickness direction between the laminae. The overall performance of any composite structures and assemblies largely depends on the interlaminar properties and the performance of its bonded joints. Various techniques and processes were developed in recent years to improve mechanical performance of the composite structures and assemblies, one of which includes the use of nanoscale reinforcements in between the laminae and within the adhesive layer.

In the present work we studied the edge trimming process of CFRP with a diamond interlocking “burr” tool. Measurements of tool wear, surface roughness, spindle power and delamination depth were performed for different combinations of spindle speed and feed rate and were subsequently used to characterize machining quality. It was found that direct wear measurement for this type of cutting tool is not conclusive and thus not suitable for assessing tool life and machining quality. Instead, indirect indicators of tool wear were found more suitable for this purpose. Using these indirect methods an equation for tool life was defined and parameters for optimum machining quality were determined.

The work presented here illustrates the wear behavior of CVD diamond coated carbide tools during the machining of carbon fiber-reinforced composites. Cutting experiments were conducted on a CNC milling machine for edge trimming of a 9-mm thick multi-layered carbon fiber-reinforced epoxy laminate in a climb cutting configuration. The effects of feed speed and diamond film thickness on the wear behavior of the coated tools were determined. In addition, characteristics of the worn cutting edge were studied using optical and scanning electron microscopes. It was shown that diamond coated tools generally performed better than the uncoated tools under all conditions. Uniform wear by abrasion of the diamond film, without exposing the substrate, was obtained when cutting at low feed speeds with thicker coatings. At higher feed speeds the wear of the coated tools was characterized by abrasion through the diamond film and exposure and wear of the substrate.

Laminated metal-metal composites can have attractive fracture toughness properties; they also offer potentially good fatigue performance. These attributes are reviewed and prospects for improvement discussed. Weak interlaminar bonds are seen to be important, while quite thin layers seem to be most promising for laminates of higher strength materials. The experimental program utilized 0.033 in (0.84 mm) thick laminae of 7075-T6 aluminum alloy, adhesively bonded. Eight-layer composites were compared with solid sheets of nearly the same total metal thickness. Both fracture toughness and fatigue properties were determined. Kc values of more than double the KIc for this alloy were observed in the laminates, while fatigue performance as indicated by comparative S-N curves was found to be slightly improved.

While most industries have already adopted the use of IP networks to exploit the many advantages of network connectivity, the aircraft industry still has not significantly deployed networked devices in the aircraft. Security and reliability are two main concerns that have slowed the transition to this technology. The ability for Air Traffic Control to send digital communications to aircraft could significantly improve the aircraft safety by improving the speed and efficiency of communications. In addition, if devices could offload flight data to servers on the ground for analysis, the accuracy and efficiency of maintenance and other decisions impacting the aircraft could significantly improve. The purpose of this research is to propose an IP-based LAN architecture for the aircraft which provides a scalable solution without jeopardizing flight safety.

This paper presents experimental methods for investigating large droplet impingement dynamics and for obtaining small and large water droplet impingement data. Droplet impingement visualization experiments conducted in the Goodrich Icing Wind Tunnel with a 21-in chord NACA 0012 airfoil demonstrated considerable droplet splashing during impingement. The tests were performed for speeds in the range 50 to 175 mph and with cloud median volumetric diameters in the range of 11 to 270 microns. Extensive large droplet impingement tests were conducted at the NASA Glenn Icing Research Tunnel (IRT). Impingement data were obtained for a range of airfoil sections including three 36-inch chord airfoils (MS(1)-0317, GLC-305, and NACA 652-415), a 57-inch chord Twin Otter horizontal tail section and 22.5-minute and 45-minute LEWICE glaze ice shapes for the Twin Otter tail section. Small droplet impingement tests were also conducted for selected test models.