Search Results

Vehicle exhaust waste-heat recovery with thermoelectric power generators can improve energy efficiency, as well as vehicle fuel economy. In the conventional structure, the hot-end of thermoelectric module is directly connected with the outer wall of the exhaust pipe, while the cold-end is connected with the water pipe’s outer wall of the vehicle engine cooling cycle. However, the variety of vehicle engine operating conditions leads to the instability of the hot-end temperature, which will reduce the generating efficiency of the thermoelectric modules and also shorten its service life. This research is on the basis of constructing a heat transfer oil circulation, and to study the action principles and implementation methods of it.

A new in-line small diameter, tube and fin aluminum heat exchanger has been developed for automobile air conditioning condenser use. This condenser, while maintaining heat transfer performance, reduces weight, package volume, air flow resistance, and manufacturing complexity.

The performance of an organic Rankine cycle (ORC) that recovers heat from the exhaust of a heavy-duty diesel engine was simulated. The work was an extension of a prior study that simulated the performance of an experimental ORC system developed and tested at Oak Ridge National laboratory (ORNL). The experimental data were used to set model parameters and validate the results of that simulation. For the current study the model was adapted to consider a 15 liter turbocharged engine versus the original 1.9 liter light-duty automotive turbodiesel studied by ORNL. Exhaust flow rate and temperature data for the heavy-duty engine were obtained from Southwest Research Institute (SwRI) for a range of steady-state engine speeds and loads without EGR. Because of the considerably higher exhaust gas flow rates of the heavy-duty engine, relative to the engine tested by ORNL, a different heat exchanger type was considered in order to keep exhaust pressure drop within practical bounds.

A rotary heat exchanger may be mounted at either the hub or the rim. In either case, the mounting system must be capable of thousands of hours of operation, unlubricated, and in a highly oxidizing environment at temperatures in excess of 250°C (482°F). The development of both a hubmounted and a rim mounted system is described in this paper, and pertinent test results in the solution of durability problems peculiar to each system are reviewed. These results are based on over 300,000 hours of turbine engine test experience on rotary ceramic heat exchangers.

In order to make full use of engine exhaust heat, the thermoelectric module been used to contribute to thermoelectric power generation in the automotive. At present, the thermoelectric generators (TEGs) have been developing with continuously advances in thermoelectric technology. And almost all of the existing thermoelectric technologies are adding a gas tank to the vehicle exhaust system which increases the exhaust back pressure and occupying excessive space of the vehicle chassis. In this study, a new TEG integrated with a front silencer muffler (FMTEG) is proposed. The muffler is reshaped as the heat exchanger which has a hexagon cross-section. The water tank and clamping mechanism have been redesigned for the new heat exchanger. The FMTEG system’s dimensions are small that can well meet the installation requirements and has a good compatibility with the vehicle exhaust system.

With great development of thermoelectric exhaust heat recovery technology, more and more attention has been paid to optimization of automotive thermoelectric generators (ATEGs). A lot of work has been done on optimization of flow field and thermal analysis. However, investigation on acoustic optimization is rather limited. In this paper, efforts have been paid to study the acoustic performance of a flat-plate TEG, and the feasibility of integration of automotive exhaust thermoelectric generator with muffler was discussed. The internal configuration of heat exchanger looks like “fishbone”. Four factors have been taken into consideration: the spacing of two fins, angle of the fins, the diameter of inlet and outlet of exchanger; and filling sound absorbing material in heat exchanger chamber. Based on these four factors, acoustic analysis was carried out.

The thermal management system of the water medium retarder using engine coolant (water and ethylene glycol) as transmission medium, omits oil-water heat exchanger in the structure. When the hydraulic retarder is operated, the valve is connected with the retarder and water pump, and then the engine coolant enters the working chamber. The kinetic energy of the vehicle is converted into internal energy of the coolant, and the heat is discharged to the external environment through the engine thermal management system. The braking torque of the water medium hydraulic retarder is determined by the water medium flow rate in the working chamber. The smaller the valve opening degree, the greater the braking torque and the faster the heating transmission fluid. Small valve opening is not conducive to the loss of heat. It will affect the normal working of the engine and hydraulic retarder.

The use of exhaust gas recirculation (EGR) in internal combustion engines has significant impacts on combustion and emissions. EGR can be used to reduce in-cylinder NOx production, reduce emitted particulate matter, and enable advanced forms of combustion. To maximize the benefits of EGR, the exhaust gases are often cooled with on-engine liquid to gas heat exchangers. A common problem with this approach is the build-up of a fouling layer inside the heat exchanger due to thermophoresis and condensation, reducing the effectiveness of the heat exchanger in lowering gas temperatures. Literature has shown the effectiveness to initially drop rapidly and then approach steady state after a variable amount of time. The asymptotic behavior of the effectiveness has not been well explained. A range of theories have been proposed including fouling layer removal, changing fouling layer properties, and cessation of thermophoresis.

For vehicle thermoelectric generator, heat would be directly transferred into electricity by thermoelectric modules because there was temperature difference between heat exchanger and water tank. The electrical power generation was deeply influenced by temperature difference, temperature uniformity and topological structure of TEG. In previous works, increasing the difference of temperature would significantly enhance the power generation of TEG and inserted fins were always applied to enhance heat transfer in parallel-plate heat exchanger. But fins would result in a large backpressure which was not conductive to efficiency of the engine.In current study, to enhance heat transfer rates and outside surface temperature, cylindrical grooves on the top and bottom surface in heat exchanger was proposed. The cylindrical grooves could increase the heat transfer area and enhance the turbulence intensity, meanwhile there was no inserts in the fluid to block the flow.

The Electronic Automatic Temperature Control (EATC) system provides the customer with a continuously variable blower motor operation. The high current is controlled by a power transistor. This device, which is capable of dissipating over 100 watts, requires a heat sink capable of thermally conducting the heat source to atmosphere (figure 1). Louvered fin heat exchangers have already been optimized for use in radiators and condensors. The same technology, using vacuum brazing techniques, was applied to develop a heat sink for electrical components. To do so, power transistor operating and cycling temperatures, A/C system airflow and airflow velocity had to be considered. An operating system was designed where all of the design criteria were met.

The hydraulic retarder is a significant auxiliary braking device [1] for the heavy duty vehicle. Traditionally, cooling circulatory system of the hydraulic retarder was coupled with the engine cooling system [2], and the thermal energy of the transmission medium would be cooled by the engine radiator ultimately. For this scheme, radiator's spare heat removal capacity could be fully utilized whereas the cooling system is very complicated and is hard to maintain. Furthermore, the corresponding of thermal management system lags behind the power change of the retarder. In this research, integrated cooling evaporation system is developed for the hydraulic retarder, which makes the cooling water contact with the transmission medium through the stator wall, so that it can rapidly response to the thermal variation of the retarder, keep the stability of the oil temperature and meanwhile reduce the risk of cooling medium leakage.

In an automotive engine cooling system, the heat rejected to the coolant by the engine and other components is transferred to the air by the radiator. The cooling system engineer must predict the coolant inlet temperature (the top water temperature) for each operating conditions of interest. Computational fluid dynamics (CFD) computer programs have been developed to predict the cooling air flow velocities and temperatures entering the radiator. Radiator effectiveness is measured on a calorimeter with uniform air velocity and temperature entering the radiator. Computer programs have been developed to predict calorimeter performance for new radiators based on experimental data from existing components. In applying the calorimeter performance model to a vehicle, some means must be used to derate the performance slightly based on the non-uniform inlet air velocity and temperature distribution entering the radiator.

A low-pressure CO2-based climate-control system has the environmental benefits of CO2 refrigerant but avoids the extremely high pressures of the transcritical CO2 cycle. In the new cycle, a liquid “cofluid” is circulated in tandem with the CO2, with absorption and desorption of CO2 from solution replacing condensation/gas cooling and evaporation of pure CO2. This work compares the theoretical performance of the cycle using two candidate cofluids: N-methyl-2-pyrrolidone and acetone. The optimal coefficient of performance (COP) and refrigeration capacity are discussed in terms of characteristics of the CO2-cofluid mixture. Thermodynamic functions are determined either from an activity coefficient model or using the Soave equation of state, with close agreement between the two approaches. Reductions in COP due to nonideal compressor and heat exchangers are also estimated.

The potential for automotive exhaust-based thermoelectric generator (TEG) has been increasing with continuously advances in thermoelectric technology. In this paper, the thermal deformation of the TEG system is studied on the basis of the surface temperature distribution of the heat exchanger. The simulation result shows that thermoelectric modules (TMs) on different positions have different thermal performance which can significantly influence the power generation efficiency of the system. Meanwhile, in terms of the working performance of TMs, the clamping mechanism is considered to have some effects on both the cold side and the hot side of TEG. Following the simulation, bench tests are carried out to confirm the reasonability of the simulation results.

Turbochargers can improve vehicle dynamic performance and fuel economy and are applied widely nowadays. Due to the existence of turbocharger delay effect, acceleration delay and insufficient combustion are its disadvantages. By collecting high pressure gas which generates from the inertia of the turbine in the intake passage when the vehicle slows down, the gas can be supplied for the shortage while the vehicle is accelerating, which can reduce turbocharger delay effect directly. However, turbocharger delay effect changes a little at high speed and low speed which is subjected to the air inflation and short air-release time. This paper adds a set of pressure booster device on the existing inflating-deflating device, whose thermal energy comes from the compressed air and lubricating oil, to facilitate pressure increasing in inflating-deflating device and help the chamber change sooner, which avails to relieve the delay effect.

The galvanostatic polarization method was used to determine the pitting potentials of candidate wrought aluminum alloys in inhibited ethylene glycol engine coolants. It was shown that the relative value of the pitting potential is an excellent measure of the long-term effectiveness of the coolants in preventing spontaneous pitting and crevice attack in the aluminum heat exchangers. The long-term effectiveness was determined by metallographic examination of aluminum heat exchangers subjected to a four-month, 50,000 mile simulated service circulation test.