Search Results

Vehicle exhaust waste-heat recovery with thermoelectric power generators can improve energy efficiency, as well as vehicle fuel economy. In the conventional structure, the hot-end of thermoelectric module is directly connected with the outer wall of the exhaust pipe, while the cold-end is connected with the water pipe’s outer wall of the vehicle engine cooling cycle. However, the variety of vehicle engine operating conditions leads to the instability of the hot-end temperature, which will reduce the generating efficiency of the thermoelectric modules and also shorten its service life. This research is on the basis of constructing a heat transfer oil circulation, and to study the action principles and implementation methods of it.

The hydraulic retarder, which is an auxiliary brake device for enhancing traffic safety, has been widely used in kinds of heavy commercial vehicles. When the vehicle equipped with the retarder is traveling in non-braking state, the transmission loss would be caused because of the stirring air between working wheels of the rotor and the stator no matter if the retarder connects in parallel or in series with the transmission [1]. This paper introduces an elaborate hydraulic retarder air-friction reduction system (AFRS) which consists of a vacuum generating module and pneumatic control module. AFRS works to reduce the air friction by decreasing the gas density between working wheels when the retarder is in non-braking state. The pneumatic control model of hydraulic retarder is built first. Then various driving conditions are considered to verify the performance of the AFRS. The stability of the AFRS is analyzed based on the complete driveline model.

The starting knock of R4102 D.I. diesel engine are analyzed experimentally based on the transient speed and first and third cylinder indicator diagrams that were taken from updated data acquisition system developed by the authors[1][2]. The influence of the starting knock on the strength of connecting rod, piston and piston ring are also studied. The results show that the influence of the starting knock is larger than the influence of the rated conditions. So the starting knock must be thought in the engine design.

Flow channels in proton exchange membrane fuel cells (PEMFC) play an irreplaceable role, and flow channel design in bipolar plates is one of the most active research areas at present. The flow channel on the cathode side needs to discharge liquid water out of the fuel cell in time and allow oxygen to flow to the cathode catalytic layer as much as possible to avoid the phenomenon of cathode water flooding and mass transfer loss. In order to improve the performance of PEMFC, a method of setting both side blockages in the cathode flow channel is proposed. In this paper, lateral blockage models with three shapes are proposed to study the influence of blockage on mass transfer and performance. First, a 3D PEMFC model with a middle channel was built to calculate the fuel cell power at different discharge rates.

Head-up Display (HUD) system can avoid drivers’ distraction on dashboard and effectively reduce collisions caused by emergency events, which is gradually being realized by researchers around the world. However, the current HUD only displays information like speed, fuel consumption, other information like acceleration and braking can’t be displayed yet. This research will use the indicator symbol‘s color and position change to remind drivers to brake or accelerate. Drivers can do driving operation timely and accurately. The system has the advantages of safety, intuition and real-time. The vehicle safe speed is calculated according to the road parameters, like adhesion coefficient and slope, and vehicle parameters, such as vehicle mass and centroid. Then, the appropriate braking operations are obtained by combining the vehicle driving state. The braking information is corresponded to the color and position change of the indicator symbol to prompt the drivers by the HUD interface.

Systematic research on dynamic model, simulation analyses, prototype production and bench tests have been carried out in recent years on the most popular energy-harvesting shock absorbers-the mechanical motion rectifier (MMR), and the hydraulic-electromagnetic energy-regenerative shock absorber (HESA). This paper presents a novel application of the HESA into bogie system of railway vehicles. In order to study the differences of suspension performance and energy harvesting property between first suspension system and second suspension system of the application, simulation models are built in AMESim to make comparison studies on the different department suspensions caused by the nonlinear damping behaviors of the HESA. The simulation results show that the system can effectively reduce the impact between wheel and rail tracks, while maintaining good potential to recycle vibratory energy.

To study the mechanism of the effect of low-viscosity oils on engine friction loss reduction so as to improve the vehicle fuel economy of the Worldwide harmonized Light vehicles Test Cycle (WLTC) by upgrading the Society of Automotive Engineers (SAE) viscosity grade of the factory fill oil from 5W30 to 0W20, eight 0W20 oil samples were blended with different doses of base oil, viscosity modifier (VM), and friction modifier (FM). Theoretical analysis by AVL-EXCITE simulation of the key friction pairs combined with practical engine friction torque test and vehicle WLTC fuel consumption tests were carried out. The results showed that 0W20 oils can effectively reduce the engine friction torque by 5.64 Nm and the friction loss by 11.95% with the throttle fully opened; while with the throttle closed, the friction torque decreased by 3.53 Nm and the friction loss by 11.26%, resulting to the improvement of the vehicle WLTC fuel economy by 2.08%.

A patented VCC (variable combustion chamber) piston mechanism is presented, by which excess in-cylinder pressure would be able to be limited effectively based on each working cycle while a spark-ignition engine running with higher CR (compression ratio) of 12.0:1. A conventional engine can be converted to a VCC engine just by replacing its typical pistons with VCC pistons. Besides the benefits that VCR (Variable Compression Ratio) has been still pursued so far, there would be other advantages for VCC engine, such as excellent fuel economy at each load not only at light loads, and the improvement of cycle-by-cycle variation of in-cylinder pressure, and high reliability with simple structure. The innovative design of VCC piston is introduced. The main design features of VCC piston are a VCC mechanism assembled between the piston crown and the piston skirt, and a special reset cam assembled at the wrist-pin end of the connecting rod.

Radiative cooling uses the cold space source to cool the object. The radiative cooling film prepared based on the principle can reduce the fuel consumption of automobile air conditioning refrigeration. In this paper, according to the passive radiative cooling principle, taking SiO2 as the radiative cooling film of infrared radiation material, the theoretical cooling value of the passenger compartment of the automobile is calculated and analyzed based on the heat balance equation. The influence of radiative cooling film on the temperature field of passenger cabins was studied by finite element analysis. The results show that the cooling film made of SiO2 as passive radiation material has an apparent cooling effect on the passenger cabins. At the ambient temperature of 35.15°C, the theoretical cooling temperature is 6.7K. When the radiative cooling film is applied to automobiles, the cooling value of the passenger cabin body, seat, instrument panel, and other parts reaches 2.2K-5.1K.

A new type of dual fuel supply system has been developed. This system is able to economically convert conventional diesel engines into dual-fuel engines like LPG/Diesel engines and CNG/Diesel engines, which are capable of either using single diesel fuel or using dual-fuel including both diesel and CNG fuel or both diesel and LPG fuel. These diesel-LPG engines have been applied to the diesel buses in the public transportation of Guangzhou city, one of the biggest cities in China, owning to their low soot emissions, excellent operating performances and extremely low cost as well. Compared with the diesel baseline engine, it was found that there were a significant reduction in soot emission and an improvement of the fuel consumption with the diesel-LPG engine. Also the strategy on LPG content is discussed in order to meet the demands for soot emission, fuel economy, transient performance and output power at the same time.

There are a large number of curves and slopes in the mountainous areas. Unreasonable acceleration and deceleration in these areas will increase the burden of the brake system and the fuel consumption of the vehicle. The main purpose of this paper is to introduce a speed planning and promotion system for commercial vehicles in mountainous areas. The wind, slope, curve, engine brake, and rolling resistances are analyzed to establish the thermal model of the brake system. Based on the thermal model, the safe speed of the brake system is acquired. The maximum safe speed on the turning section is generated by the vehicle dynamic model. And the economic speed is calculated according to the fuel consumption model. The planning speed is provided based on these models. This system can guide the driver to handle the vehicle speed more reasonably.

In the Plug-in hybrid electric bus, the power train parameter and control strategy significantly affect the economy and dynamic performance. Thus, the simultaneous optimization of power train parameter and control strategy is designed for the trade-off between the dynamic and economic performance. Depending on the parallel electric auxiliary control strategy in a plug-in hybrid electric bus, a vehicle dynamic simulation model is built with the software AVL Cruise. Aiming at the minimization of equivalent gas consumption and acceleration time from 0 to 50kmph, the gear ratio, final drive ratio, gear shifting strategy and control strategy are chosen as optimal variable, which significantly impact power performance and fuel economy. The driving performance and the driving range with full battery are considered as constraints. Based on the software Isight, multi-objective optimization model is built by adopting non-dominated sorting genetic optimization algorithm (NSGA-II).

A zero-dimension combustion model suitable to multi-fuel combustion process has been developed and successfully used in the analysis of methanol combustion process The V2b function is calculated with the Powell Optimized Algorithm. The concerned characteristics include in the variables of zero-dimension model, mean indication pressure, maximum combustion pressure, ignition delay and the correlation coefficient between heat release rate and ignition delay. The heat release rate curves on different conditions are fitted and the statistic analyses of the cyclic variations are conducted.

The new DI diesel engine combustion system named Double-Layer Diverging Combustion System (DLDCS) results in a better Brake Specific Fuel Consumption (BSFC) and lower exhaust emissions. The previous results of numerical simulation and bench test of a single cylinder DI diesel engine showed that more homogeneous fuel distribution, better BSFC and lower emission level were obtained by employing this combustion system. In this research, further numerical simulation are employed to seek the best injection advance angle and investigate the influence of different volume fraction and type lines of upper layer with AVL Fire.

Fuel injection and fuel-air mixture formation processes have significant influence on the performance of spark ignition gas engines. In order to study the fuel enrichment injection process in the pre-chamber of a marine gas engine, the flow field in the pre-chamber during the gas fuel injection period was investigated by the particle image velocimetry (PIV) method. An organic glass model of pre-chamber was made for optical measurement. The flow fields in the pre-chamber with four different gas injection angles were analyzed, respectively. The measurement results were qualitatively compared to the CFD calculation results as the verification of the calculation. Based on the comparison of the PIV experiment results, an optimal gas fuel injection angle was chosen. Furthermore, 3D CFD calculation models with the baseline and optimal fuel injection angles of a marine spark ignited natural gas engine were generated to calculate the working process.

Lane changing manoeuvers is an essential rudiment in vehicle driving and has a significant impact on the characteristics of traffic flow. In the case of traditional cars, the driver operates the vehicle to complete the lane change whilst for autonomous vehicles, completing the lane change requires planning the lane change trajectory and controlling the vehicle speed during the lane change. Unreasonable lane change trajectory and vehicle speed may cause the vehicle to lose stability, threaten driving safety, increase energy consumption and waste energy. This paper considers the safety and economy of the lane changing process, and proposes a new lane changing method for vehicles.

In winter, the temperature of the coldest month is below -20°C. Low temperature makes it difficult to start a diesel engine, combust sufficiently, which increases fuel consumption and pollutes the environment. The use of an electric power-driven auxiliary heating system increases the battery load and power consumption. Solar thermal energy has the advantages of easy access, clean and pollution-free. The coolant in the cylinder block of the diesel engine has a large contact area within the cylinder and is evenly distributed, which can be used as a heat transfer medium for the warm-up. A one-dimensional heat transfer model of the diesel engine block for the coolant warm-up is developed, and the total heat required for the warm-up is calculated by an iterative method in combination with the warm-up target.

Because of the long driving range and good power performance, plug-in hybrid electric vehicles (PHEV) have drawn much attention. And the current fuel-saving effect of PHEV still has a lot of room for improvement. The complex powertrain structure of PHEV makes the requirements for control strategy be increasing. Therefore, it is crucial to develop an efficient control strategy to ensure that the PHEV operates at optimal performance with an improved driving range. This paper establishes a mathematical model for fuel economy control of PHEV, by treating the torque distribution problem as a multi-stage decision optimization problem, and establishes a global energy management strategy based on a dynamic programming (DP) algorithm. Based on the actual physical model, this paper creatively solves the correction range of battery SOC value according to the charge and discharge power of the motor, which greatly reduces the calculation time of the DP algorithm.

In the intelligent speed planning system, real-time estimation of road slope is the key to calculate slope resistance and realize the vehicles’ active safety control. However, if the road slope is measured by the sensor while the commercial vehicle is driving, the vibration of the vehicle body will affect its measurement accuracy. Therefore, the relevant algorithm is used to estimate the real-time slope of the road when the commercial vehicle is driving. At present, many domestic and foreign scholars have analyzed and tested the estimation of road slope by the least square method or Kalman filter algorithm. Although the two methods both can achieve the estimation, the real-time performance and accuracy still need to be improved. In this paper, for traditional fuel commercial vehicle, the Kalman filter algorithm based on the kinematics and the extended Kalman filter algorithm based on the longitudinal dynamics are respectively used to estimate the road slope.

Heavy commercial vehicle drivers may frequently shift gears when they are running on long and downhill roads in mountainous area. In order to improve driving safety and fuel economy, it is necessary to predict the slope of the road ahead in real time and correct the driver's shift strategy in time. At present, the road slope estimation is mainly based on the real-time estimation of the road slope at the current position of the vehicle based on the vehicle driving information obtained by the sensors, but the road slope of the road section that the vehicle is about to reach has not been predicted. In this paper, based on the road slope information of the road section that the driver has driven through, combined with Geographic Information System (GIS) information and road design standards, the slope of the road section ahead is predicted.